• Journal of the Korean Wood Science and Technology
• /
• 제36권5호
• /
• pp.42-48
• /
• 2008

This study was conducted to discuss the effects of hardener and extender contents on peak temperature, reaction enthalpy (${\Delta}H$), gelation time, viscosity change, and pH value in three types of UMF (urea-melamine- formaldehyde) resin with the help of perpHecT LogR meter, differential scanning calorimetry (DSC), and advanced rheometric expansion system (ARES), The results indicated that the pH value of Control A steeply decreased to 5,2 in the early stage but relatively remained constant thereafter as in Synthesis 1 and Synthesis 2, The peak temperature and time decreased as well, whereas ${\Delta}H$ and viscosity increased with the increase of hardener content. On the other hand, ${\Delta}H$ was not changed up to the extender content of 5% and then decreased with its further addition, And the pH value and peak temperature showed no change with the increase of extender content at the hardener content of 5% in three types of UMF resin, The effect of hardener content in this experiment, however, appeared more conspicuous in Control A than in the other two types of Synthesis 1 and Synthesis 2, These results might be caused by higher molecular weight with longer chains of methylene ($-CH_2-$) and methylene ($-CH_2-O-CH_2-$) ether bridges or much more branched chains in Control A.

• Journal of Adhesion and Interface
• /
• 제10권4호
• /
• pp.199-206
• /
• 2009

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.179-186
• /
• 2011

In an effort to understand the hydrolytic degradation process of cured urea-formaldehyde (UF) resins responsible for the formaldehyde emission of wood-based composite panels, this study analyzed the influence of acid hydrolysis on the morphology of cured UF resins with different formaldehyde/urea (F/U) mole ratios such as 1.6, 1.4, 1.2 and 1.0. Field emission-scanning electron microscopy (FE-SEM) was employed to observe both exterior and fracture surfaces on thin films of cured UF resins before and after the etching with hydrochloric acid as a simulation of the hydrolytic degradation process. FE-SEM images showed that the exterior surface of cured UF resin with the F/U mole ratio of 1.0 had spherical structures after the acid hydrolysis while the other cured UF resins were not the case. However, the fracture surface observation showed that all the samples possessed spherical structures in the cured state of UF resins although their occurrence and size decreased as the F/U mole ratio increased. For the first time, we found the spherical structures in cured UF resins of higher F/U mole ratio of 1.4. After the acid hydrolysis, the spherical structures became a much predominant at the fracture surface. These results indicated that the spherical structures in cured UF resinswere much more resistant to the hydrolytic degradation by the acid than amorphous region.

• Current Research on Agriculture and Life Sciences
• /
• 제32권3호
• /
• pp.125-130
• /
• 2014

This study used transmission electron microscopy (TEM) to investigate the micro-morphological features of two formaldehyde to urea (F/U) mole ratio liquid urea-formaldehyde (UF) resins with three hardener levels as a function of the curing time. The micro-morphological features of the liquid UF resins were characterized after different curing times. As a result, the TEM examination revealed the presence of globular/nodular structures in both liquid UF resins, while spherical particles were only visible in the low F/U mole ratio resins. The high F/U mole ratio liquid UF resins also showed extensive particle coalescence after adding the hardener, along with the appearance of complex filamentous networks. When the resins were cured with a higher amount of hardener and longer curing time, the spherical particles disappeared. For the low mole UF resins, the particles tended to coalesce with a higher amount of hardener and longer curing time, although discrete spherical particles were still observed in some regions. This is the first report on the distinct features of the crystal structures in low F/U mole ratio UF resins cured with 5% hardener and after 0.5 h of curing time. In conclusion, the present results indicate that the crystal structures of low F/U mole ratio UF resins are formed during the curing process.

• Korean Journal of Heritage: History & Science
• /
• 제44권4호
• /
• pp.130-141
• /
• 2011

This paper examined the bleaching effect of the two types of gel made with neutralizing agent such as sodium meta silicate gel & triethylamine gel mixed with carbopol resin 940 & 934 which has thickness effect in broad pH region and mixed with 10% hydrogen peroxide. Sodium meta silicate gel(1.6g included) provided pH 10, the most suitable environment for bleaching. The result of comparison of the baseline colour changes(${\Delta}E*ab$) and colour changes according to time(${\Delta}E*ab$) is as following. Group1(carbopol 940, sodium meta silicate, Urea Hydrogen Peroxide) showed 112% efficiency at CS-2; 63.3% at CS-4; 87.4% at CS-6. Group2(carbopol 934, sodium meta silicate, Urea Hydrogen Peroxide) showed 77.3%, 67.3%, 109.6% at CS-8, CS-10, CS-12 respectively; CT-1, CT-3, CT-5 of Group3(carbopol 940, triethylamine, Urea Hydrogen Peroxide) showed 36.8%, 73.2%, 74%; In Group4(carbopol 934, triethylamine, Urea Hydrogen Peroxide), efficiency of CT-6, CT-8, and CT-10 was 81.7%, 95.4%, and 95.7%. The paper showed that various concentration of neutralizing agent such as sodium meta silicate and triethylamine have bleaching effect. Viscosity of the gel including sodium meta silicate was higher than the gel including triethylamine. High viscosity helps the bleaching gel sit on the smooth slope of the ceramics. As a result, sodium meta silicate is considered to provide thickening and bleaching effect required in producing 10% hydrogen peroxide gel.

• Journal of the Korean Wood Science and Technology
• /
• 제4권1호
• /
• pp.28-32
• /
• 1976

This study was carried out to know the adaptability of barley flour, potato flour and white ash as extender and filler of urea-formaldehyde resin for plywood as a substitute material of wheat flour. The extenders and filler used at this study were extended by several groups of percentages. Shear strength, moisture contents, and specific gravities were compared among tested groups. The results obtained are summarized as follows. 1) Wet and dry shear strength of plywoods extended by 10% barley flour, 30% potato flour, and wheat flours were shown better results than non extended plywoods. 2) There was no significant difference between plywoods extended until 50% barley flours and non extended plywoods. 3) Shear strength of plywoods extended by 50% potato and 100% barley flours were shown worse result than non extended. 4) Dry and wet shear strength of plywoods extended by white ash were shown worst result. 5) The plywoods extended by potato flours were shown not only better shear strength, but also considered more profitable cost for extending.

• Journal of the Korean Wood Science and Technology
• /
• 제15권4호
• /
• pp.64-68
• /
• 1987

To develope the utilities of the chestnut bur, which is wasted after harvesting chestnut in farmhouses, the feasibilities of adhesion(urea resin) extenders of the powder for plywood were examined. These experiments were implemented on experimental scale at Forestry Research Institute(Seoul) and on a plywood mill scale at Eugon Industrial Co LTD(Inchon) for more reliable data. In this paper, it was proved that the chestnut bur powder caused to rise the glue viscosity but the chaff powder to down reversely. The most effective mixing ratio were wheat flour 5kg, chaff powder: 5kg and chestnut bur powder. 5kg per 100kg of urea resin. At this condition, the viscosity were most appropriate (1,320 2,230 cps) for glue spreading operations, and the dry shear strengthes were most adequate(10.7-13.2kg/$cm^2$), wood failure ratio 82-88%). The chestnut bur powder, can be utilized for plywood adhesion extenders without any change of present process lines in plywwod mills.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.43-45
• /
• 2011

As technologies evolve, building large concrete structures ever built, but due to lack of maintenance after completion of concrete corrosion, leaks, and preparedness from the problem that is an urgent need. In particular, water-resistant variety of concrete structures. How the concept applies to the most important public drinking water purification and drinking water that is draining the production and storage, and distribution as the structure cause damage to the structure when the contaminated water is supplied to each home that can harm the health of citizens is the cause. Therefore, the correct choice of materials, and thorough a lot of investment in construction and maintenance should have. In this study, unlike conventional water-proof materials, methods, and in other reactions easily than conventional poly-urea resins have good physical performance and chemical resistance, high performance polyurea resin performance review of the physical infrastructure of the country for the longevity of would like to make long-term durability.

• Textile Coloration and Finishing
• /
• 제9권2호
• /
• pp.41-49
• /
• 1997

To control free formaldehyde release from fabric finished with N-methylol compounds, resin finished cotton fabric was treated with resorcinol solution, dried and cured. Factors affecting to control formaldehyde release have been investigated. It was shown that the aftertreatment with resorcinol greatly suppressed the free formaldehyde release. Up to concentration of about 5% of resorcinol, the concentration of resorcinol effected on the control of free and evolved formaldehyde. And at high concentration of resorcinol, however, the concentration became rather insensitive to contol formaldehyde release. Addition of some salt catalysts such as ammonium chloride, zinc nitrate, sodium acetate and ammonium acetate, was effective in decreasing formaldehyde release. Considering the effect on the control of formaldehyde and crease recovery, ammonium acetate was concidered to be the best catalyst. It was observed that the optimum curing temperature for the resorcinol treatment was about 15$0^{\circ}C$, and that the curing time did not affected formaldehyde release over three minutes. Although the treatment of resorcinol had a little adverse effect on crease recovery of resin finished fabric, this effect could be negligible.

• Journal of the Korean Wood Science and Technology
• /
• 제35권5호
• /
• pp.58-66
• /
• 2007

The objective of this research was to develop environment-friendly adhesives for face fancy veneer bonding of engineered flooring. Urea-formaldehyde (UF)-tannin and melamine-formaldehyde (MF)/PVAc hybrid resin were used to replace UF resin in the formaldehyde-based resin system in order to reduce formaldehyde and volatile organic compound (VOC) emissions from the adhesives used between plywoods and fancy veneers. Wattle tannin powder (5 wt%) was added to UF resin and PVAc (30 wt%) to MF resin. These adhesive systems showed better bonding than commercial UF resin with a similar level of wood penetration. The initial adhesion strength was sufficient to be maintained within the optimum initial tack range. The standard formaldehyde emission test (desiccator method) and VOC analyzer were used to determine the formaldehyde and VOC emissions from engineered flooring bonded with commercial UF resin, UF-tannin and MF/PVAc hybrid resin. By desiccator method, the formaldehyde emission level of UF resin showed the highest but was reduced by replacing with UF-tannin and MF/PVAc hybrid resin. MF/PVAc hybrid satisfied the $E_1$ grade (below $1.5mg/{\ell}$). VOC emission results by VOC analyzer were similar with the formaldehyde emission results. TVOC emission was in the following order: UF > UF-tannin > MF/PVAc hybrid resin.