• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.141-141
• /
• 2009

본 실험에서는 비평형 마그네트론 스퍼터링 (Unbalanced Magnetron Sputtering, UBMS)을 이용하여 제작된 ITO 박막의 전기적, 광학적, 구조적인 특성들에서 기판온도와 자장 변화의 영향에 대해 연구하였다.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.84-87
• /
• 2003

Since Pb-free solder alloys have been used extensively in microelectronic packaging industry, the interaction between UBM (Under Bump Metallurgy) and solder is a critical issue because IMC (Intermetallic Compound) at the interface is critical for the adhesion of mechanical and the electrical contact for flip chip bonding. IMC growth must be fast during the reflow process to form stable IMC. Too fast IMC growth, however, is undesirable because it causes the dewetting of UBM and the unstable mechanical stability of thick IMC. UP to now. Ni and Cu are the most popular UBMs because electroplating is lower cost process than thin film deposition in vacuum for Al/Ni(V)/Cu or phased Cr-Cu. The consumption rate and the growth rate of IMC on Ni are lower than those of Cu. In contrast, the wetting of solder bumps on Cu is better than Ni. In addition, the residual stress of Cu is lower than that of Ni. Therefore, the alloy of Cu and Ni could be used as optimum UBM with both advantages of Ni and Cu. In this paper, the interfacial reactions of Sn-3.5Ag-0.7Cu solder on Ni-xCu alloy UBMs were investigated. The UBMs of Ni-Cu alloy were made on Si wafer. Thin Cr film and Cu film were used as adhesion layer and electroplating seed layer, respectively. And then, the solderable layer, Ni-Cu alloy, was deposited on the seed layer by electroplating. The UBM consumption rate and intermetallic growth on Ni-Cu alloy were studied as a function of time and Cu contents. And the IMCs between solder and UBM were analyzed with SEM, EDS, and TEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.129-133
• /
• 2019

TiN thin films were fabricated using an unbalanced magnetron sputtering (UBMS) system, and their structure and surface characteristics as well as their optical and tribological properties were evaluated. The hardness, elastic modulus, adhesive force, surface roughness, and transmittance of the Ti thin films fabricated using the UBMS system were 11.5 GPa, 103 GPa, 27.5 N, 2.45 nm and 20%, respectively. The TiN films prepared with various proportions of nitrogen as the reaction gas exhibited maximum values for the hardness, elastic modulus, critical load, RMS roughness and transmittance of approximately 19.2 GPa, 182 GPa, 27.3 N, 0.98 nm, and 85%, respectively. Moreover, the TiN thin film fabricated under the condition of 30 sccm nitrogen gas showed the optimal physical properties. In summary, the TiN thin films fabricated using the UBMS system exhibited excellent hardness, elastic modulus, adhesion, and smooth surface in addition to good hydrophilic properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.379-382
• /
• 1999

In this paper, we investigated the characteristics of MgO thin film prepared by unbalanced magnetron sputtering(UBMS) in surface discharge type AC PDP The minimum discharge voltage is obtained for the sample of substrate bias voltage-10V. Moreover the anti-sputtering characteristics of MgO thin film by UBMS is improved about 40% than one of balanced magnetron sputtering(BMS)

• Korean Journal of Metals and Materials
• /
• v.46 no.1
• /
• pp.33-38
• /
• 2008

The interfacial reactions and shear strength of pure Sn solder bump were investigated with different under bump metallizations (UBMs) and reflow numbers. Two different UBMs were employed in this study: Cu and Ni. Cu6Sn5 and Cu3Sn intermetallic compounds (IMCs) were formed at the bump/Cu UBM interface, whereas only a Ni3Sn4 IMC was formed at the bump/Ni UBM interface. These IMCs grew with increasing reflow number. The growth of the Cu-Sn IMCs was faster than that of the Ni-Sn IMC. These interfacial reactions greatly affected the shear properties of the bumps.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.3
• /
• pp.192-197
• /
• 2017

A 6-way-cross consisting of a 2.75-inch CF flange was used as a main chamber on a PFEIFFER VACUUM TMP station based on a 67 l / sec turbo molecular pump and a diaphragm pump to produce a magnet array with a volume ratio of 5.5: 1.A 1-inch diameter copper target and graphite target were fabricated using MDX-1.5K from Advanced Energy Industries, Inc as a DC power supply. Ion current density of copper target and graphite target was measured by unbalanced magnetron sputtering. The basic pressure condition was $6.3{\times}10^{-7}mbar$ and the process pressure was Ar 50 sccm at $1.0{\times}10^{-2}mbar$ (7.5 mTorr) in the Ar atmosphere. Therefore, the relative density of copper ions reaching the substrate with the measured ion current density was derived.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.70-70
• /
• 2017

TSV(through silicon via)는 긴 종횡비를 갖는 패턴에 Cu, Ta, Ti을 높은 conformality를 갖도록 증착하는 공정이다. Magnetron cathode의 자석 배열 설계는 target 물질 종류에 따라서 multitrack, water drop type등이 있으며 target과 substrate 사이의 공간에 플라즈마를 형성시켜서 기판에 이온 입사량을 늘린 후 기판 바이어스를 이용하여 이온 충돌, re-sputtering을 통한 재증착 과정을 통해 치밀한 금속 박막을 연속적으로 형성할 수 있도록 하는 것이 목적이다. 또한 sputter가 사용되고 있는 분야에 효율을 증대시키고, 증착되는 막의 품질향상을 위해 UBMS를 사용하고 있으며, 산업에 사용되어 지는 300 mm wafer용 시스템은 제작비가 약 10억 원 정도 소요되며 다양한 테스트를 진행하기 위해선 많은 비용이 소요된다. 따라서 비용과 소요시간을 줄여 다양한 테스트를 위해 소규모 플라즈마 시스템을 설계하게 되었다. 61 l/sec 터보 분자 펌프와 다이아프램 펌프를 기초로한 TMP station에 2.75 인치 CF flange가 장착된 6 way cross를 main 챔버로 활용하고, 작은 size의 unbalanced magnetron cathode를 제작, 장착한 다음 6 way cross 주변에 전자석을 적절히 배치하여 300 mm wafer system에서와 동일한 물리적 현상을 테스트 할 수 있도록 하였다. Fig1. (a) UBMS system의 사진을 나타내었고, (b)에는 6 way cross 내부에 발생된 플라즈마의 형상을 나타내었다. 전원 장치는 Advanced Energy사의 MDX-1.5K DC power supply를 사용하였고, 방전 전압 - 전류 관계의 가스 압력에 따른 plasma 현상과 magnetron 배율에 따른 plasma 현상 그리고 전자석에 의한 영향을 주로 관찰 하였다.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2236-2238
• /
• 1999

This paper deals with the surface glow discharge characteristics and some physical properties of MgO thin films prepared by RF unbalanced magnetron sputtering(UBMS) in surface discharge type AC PDP. The minimum discharge voltage is obtained for the sample of substrate holder bias voltage -10V. The main factors that improves the discharge characteristics by applied bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process Moreover, the anti-sputtering characteristics of MgO thin film by UBMS is more excellent than that of balanced magnetron sputtering(BMS) and E-beam evaporation method.

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.205-206
• /
• 2006

The microstructural evolutions and shear properties of the pure Sn solder bumps with Ni UBMs were investigated during multiple reflows and high temperature storage(HTS) tests. Only a $Ni_3Sn_4$ IMC was found at the bump/Ni UBM interface after 1 reflow. The layer thickness of these IMCs increased with increasing reflow number and testing time. The solder bumps showed a good reliability during multiple reflows and HTS tests.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.07a
• /
• pp.95-99
• /
• 2001

Cu is considered as a promising alternative interconnection material to Al-based interconnection materials in Si-based integrated circuits due to its low resistivity and superior resistance to the electromigration. New humping and UBM material systems for solder flip chip interconnection of Cu pads were investigated using electroless-plated copper (E-Cu) and electroless-plated nickel (E-Ni) plating methods as low cost alternatives. Optimally designed E-Ni/E-Cu UBM bilayer material system can be used not only as UBMs for solder bumps but also as bump itself. Electroless-plated E-Ni/E-Cu bumps assembled using anisotropic conductive adhesives on an organic substrate is successfully demonstrated and characterized in this study