• 한국해양공학회지
• /
• 제29권6호
• /
• pp.427-435
• /
• 2015

This paper provides the numerical results of a simulation of the flow around a propeller working beneath the free surface. A finite volume method is used to solve the unsteady Reynolds averaged Navier-Stokes (URANS) equations, where the wave-making problem is solved using a volume-of-fluid (VOF) method. The numerical analysis focuses on the propeller wake structure affected by the free surface, where we consider another free surface boundary condition that treats the free surface as a rigid wall surface. The propeller wake under the effect of these two free surface conditions shows a reduction in the magnitude of the longitudinal and vertical flow velocities, and its vortical structures strongly interact with the free surface. The thrust and torque coefficient under the free surface effect decrease about 3.7% and 3.1%, respectively. Finally, the present numerical results show a reasonable agreement with the available experimental data.

• 자동차안전학회지
• /
• 제7권3호
• /
• pp.19-24
• /
• 2015

Brake pads are a component of disc brake system of automobile and consist of steel backing plates and friction material facing the disk brake rotor. Due to the repeated sliding forces and torque in vehicle braking, friction performance of brake pads are ensured. Futhermore, the brake pad is one of major tuning components in aftermarket, mechanical characteristics of the brake pad are necessary to evaluate for establishing the certification standards of tuning components. This study had performed the five specimen tests for friction coefficients and wear loss rates according to the SAE test specification. Using the instrumented indentation method, yield strength and tensile strength were measured. Friction coefficients, 0.386 - 0.489, and wear loss rates, 1.0% - 3.7% are obtained. The range of yield strength and tensile strength are 21.4 MPa - 105.3 MPa and 39.5 MPa - 176.4 MPa respectively.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권1호
• /
• pp.32-39
• /
• 2000

In this paper, an improved re-adhesion control scheme is proposed for 1C4M railway traction system. It is well known that the coefficient of adhesion between wheel and rail has a maximum value at a certain slip velocity. In the proposed scheme, adhesive effort is estimated by a full-order observer and the driving torque of motor is controlled to get maximum adhesive effort. The-adhesion control simulator is designed to verify the proposed re-adhesion control algorithm. The simulation results and experimental results are presented.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.36-43
• /
• 2000

In this paper a Vortex Lattice Method is used to predict the performances of a contra-Rotating Propeller. Greeley and Kerwin's(1982) wake model is adopted instead of the exact trailing vortex geometry. The interaction of the two propellers is treated by the sense that the induction of one propeller upon the other propeller is averaged in the circumferential direction . Two single propellers (DTRC 4119 & DTRC 4842) are chosen and compared with the experimental and other numerical results published. Then the computational results for three CRP's (4-0-4 CRP(DTRC 3686+DTRC 3687A) 4-0-5 CRP(DTRC 3686+DTRC 3849) & DTRC CRT(DTRC 5067+DTRC 5068) are compared with the experimental and numerical results published. The interaction of both propellers by the change of inflow velocity and circulation of each propeller is investigated.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.516-517
• /
• 2016

I use Jansen mechanism to reduce the unnecessary motion of car body and improve the motion performance capability in the rugged terrain To reduce the unnecessary motion, the positional variation of a main body of vehicle should be minimized. In order to reduce the change of height and control the speed at every moment when vehicle move, 16 legs or more are installed on a crankshaft and the paths of leg motions need to be considered in the rugged terrain. The vehicle will be optimized so that it produces a sufficient speed and torque for practical use. Finally, I designed proper body with Edison simulation. The simulation is good for beginners of mechanism design.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.66-73
• /
• 2004

This paper presents characteristics of combustion and exhaust gas properties according to variation of the combustion chamber for economy and emissions standards. In order to use combustion and exhaust gas properties data, it is necessary to build some data base, which use cylinder pressure sensor and emission tester. A feasibility and necessity of combustion pressure based cylinder spark timing control has been examined. So, this was obtained the coefficient of variation(COV) and the specific fuel consumption(sfc). Using the results of the test, the effects of the variable combustion chamber can be improved combustion stability and be reduced exhaust emission.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.15-21
• /
• 2003

LPG is considered as one of the most prominent alternative automotive fuels in worldwide. However, conventional mixer system can not meet the emission regulations as the mileage accumulation increased. Recently, much attention is focused on the development of LPG liquid injection fuel systems to increase the engine performance and reduce the exhaust emissions. This study evaluates the LPLi(Liquid Phase LPG injection) engine performance and exhaust emission characteristics using a 3.0 liter LPG engine. The fuel supply system and engine management system were changed from FBM into LPLi to control the precise mixture ratio and optimized spark advance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부A
• /
• pp.163-167
• /
• 1998

In this paper an improved re-adhesion control scheme is proposed for IC4M(1-Controller 4-Motors) traction system. It is well known that the coefficient of adhesion between wheel and rail has a maximum value at a certain slip velocity. In the proposed scheme, maximum adhesive force is estimated by an observer and the driving torque of motor is controlled to set maximum adhesive force. The simulation results are presented.

• 대한기계학회논문집B
• /
• 제30권3호
• /
• pp.230-237
• /
• 2006

Flows in the cavity with pump out vane are calculated using the CFX-Tascflow CFD code. flow calculations are performed for different values of vane height, numbers, leakage flow rate, and rotational speed. The flow is very complex and three dimensional with strong vortex and leakage flow over the vane. The variations of pressure coefficient and K-factor with these parameters and resulting effects on the thrust and torque are studied. The present study contributes to showing the capability of flow simulation of back cavity with pump-out vane. The calculated results are good enough to be used back cavity design.

• 한국가시화정보학회지
• /
• 제17권2호
• /
• pp.32-38
• /
• 2019

A comparison study between computational-fluid-dynamics simulation and wind tunnel test for a megawatt-class wind turbine is conducted. For the study, flow-field in wake, basic aerodynamic performance, and effect of the yaw error for a 1/86 scaled-down model of the NREL offshore 5 MW wind turbine are numerically calculated using commercial software "FloEFD" with $k-{\varepsilon}$ turbulence model. The computed results are compared to the wind tunnel test performed by the constant-velocity mode for the model. It is shown that discrepancy are found between the two results at lower tip-speed ratio and higher yaw angle, however, the velocity-defection distribution in the wake, the torque coefficient at moderated and high tip-speed ratios are in good agreement with the wind tunnel test.