• Bulletin of the Korean Chemical Society
• /
• v.33 no.4
• /
• pp.1204-1208
• /
• 2012

A new photoelectrode composed of $Sb_6O_{13}$ nanoparticles with the size of 20-30 nm has been prepared via thermolysis of a colloidal antimony pentoxide tetrahydrate ($Sb_2O_5{\cdot}4H_2O$) suspension. The $Sb_6O_{13}$ electrode showed good semiconducting properties applicable to dye-sensitized solar cells (DSSCs); the energy band gap was estimated to be $3.05{\pm}0.5$ eV and the position of conduction band edge was close to those of $TiO_2$ and ZnO. The DSSC assembled with the $Sb_6O_{13}$ photoelectrode and a conventional ruthenium-dye (N719) exhibited the overall photo-current conversion efficiency of 0.74% ($V_{oc}$ = 0.76 V, $J_{sc}=1.99\;mAcm{-2}$, fill factor = 0.49) under AM 1.5, $100\;mWcm^{-2}$ illumination.

• Journal of Magnetics
• /
• v.10 no.4
• /
• pp.163-170
• /
• 2005

The RF integrated noise filters are fabricated by photolithography. The stack for the electromagnetic noise filters consists of the nano-granular ($Co_{41}Fe_{38}AI_{13}O_8$) soft magnetic film / $SiO_2$ / Cu transmission line / seed layer (Cu/Ti) / $SiO_2$-substrate. A good signal-attenuation feature along with a low signal-reflection feature is observed in the present filters. Especially in the noise filter incorporated with a $Co_{41}Fe_{38}AI_{13}O_8$ magnetic film with lateral dimensions of $2000{\mu}m$ wide, 15 mm long and $1{\mu}m$ thick, the maximum magnitude of signal attenuation reaches -55 dB, and the magnitude of signal reflection is below -10 dB in the overall frequency range. And this level of signal attenuation is much larger than that of a noise filter incorporated with a Fe magnetic film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.274-280
• /
• 1998

Polycrystalline $Sr_2Nb_2O_7$ ceramics with very high Curie temperature were sintered using the powder derived by the chemical coprecipitation method (CCP). The phase evolution and grain-orientation of sintered samples were examined by XRD, while sintering behavior, dielectric properties and polarization were studied by SEM and ferroelectric tester. Extremely high degree of grain-orientation was observed along the (0k0) direction, which resulted in anisotropic dielectric properties of the sintered samples, with the dielectric constant values approaching those for single crystal. Thin film fabrication of $Sr_2Nb_2O_7$ in the pyroniobate family was also attempted on $SiO_2$/Si(100), Pt/$SiO_2$/Si(100), Pt/Ti/$SiO_2$/Si(100) and Pt/$ZrO_2/SiO_2/Si_2(100)$ substrates, using metalorganic decomposition (MOD) process. Neodecanoate precursor solution was prepared by mixing strontium neodecanoate with niobium neodecanoate synthesized from niobium ethoxide. It was found that $Sr_2Nb_2O_7$ single phase appeared in XRD patterns the samples annealed above $950^{\circ}C$. The effect of substrate type on film microstructure and dielectric properties was observed.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.415-423
• /
• 1996

Thin film technologies for fabricating SQUIDs involve etching and deposition procedures with the proper substrate materials and $YBa_2Cu_3O_{7-d}$ (YBCO) as the high $T_c$ superconductor. YBCO were prepared on various substrates of MgO, $SrTiO_3$, and $LaAlO_3$ by using off-axis magnetron sputtering methods and annealing in-situ. The parameters of film fabrication processes had been optimized to yield good quality films in terms of the critical temperature $T_c$ and the critical current density $J_c$. The optimized processes yielded $T_C$>90K along with $J_c$>$10_6A$$extrm{cm}^2$ at 77K and>$2\times10_7A/Cm^2$ at 5K. We fabricated step-edge type dc-SQUIDs and directly coupled magnetometers, producing step edges on MgO(100) substrates by etching with Ar-ion beam, depositing YBCO material on them, then patterning them by using ion-milling technique. Circuitizing washer-shape SQUIDs to possess a pair of step-edge junctions of 2-5$\mu$ line width with a high angle>$50^{\circ}C$ , we examined their I-V characteristics thoroughly and Shapiro steps clearly as we irradiate microwaves of 8-20 GHz frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.5
• /
• pp.415-420
• /
• 2008

AAO films were fabricated on two kinds of substrates such as $Al/SiO_2/Si$ and Al/Ni/Ti/Si. To obtain well-aligned AAO film, we optimized process condition for buffer layer, electrolyte and voltage. In the case of oxalic acid, the AAO film with pore size of approximately 45 nm was obtained at voltage of 40 V, temperature of $10^{\circ}C$, oxalic acid of 0.3 M and widening time of 60 min. Then the thickness of barrier is less than 600 nm. In the case of sulfuric acid, the AAO film has pore size of 40 nm and barrier thickness of 400 nm with optimum conditions such as voltage of 25 V, temperature of $8^{\circ}C$, sulfuric acid of 0.3 M and widening time of 60 min.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.204-205
• /
• 2007

Self-seed 층을 이용한 PLZT(9/65/35), 강유전체 박막을 Sol-Gel 법을 이용해 Pt/Ti/$SiO_2$/Si 기판 위에 증착한 후, Self-seed 층에 의한 PLZT(9/65/35) 박막의 구조적, 전기적 특성을 고찰하였다. Seed 층을 도입하지 않은 PLZT 박막의 경우 다결정 상으로 형성되는 것을 알 수 있었으며, seed 층을 도입한 PLZT 박막은 (110) 방향으로 우선 배향됨을 알 수 있었다. 증착된 PLZT(9/65/35) 박막의 유전율 및 유전손살은 10kHz에서 유전율 205, 유전손살 0.029 이었으며, Self-seed layer를 도입한 PLZT 박막의 경우 seed layer를 도입하지 않은 PLZT 박막보다 낮은 온도에서 결정화 되는 것을 관찰 할 수 있었다. Self-seed layer가 도입된 PLZT(9/65/35) 박막의 경우 잔류분극 ($P_r$) 값은 $9.1{\mu}C/cm^2$, 항전계($E_c$)는 47 kV/cm을 나타내었다.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.229-233
• /
• 1999

DC마그네트론 스퍼터링 방식으로 $Ti/SiO_2$/Si 구조 위에 Pt(200) 박막을 배향 성장시키기 위해 증착조건(스퍼터링 가스의 종류와 압력, 기판의 온도)과 후속열처리(RTA, Furnace annealing)에 따른 Pt 박막의 전기, 결정학적 특성을 조사하였다. 실험결과, 20mTorr의 Ar+O$_2$(20%)의 혼합가스 분위기에서 기판온도를 $500^{\circ}C$로 유지하여 Pt박막을 증착하고$ 600^{\circ}C$에서 30초간 급속 열처리를 실시한 경우, 90% 이상의 결정 배항도를 갖는 Pt(200) 박막을 제작할 수 있었다. 제작된 Pt(200) 박막은 $30~40\mu$Ω.cm의 낮은 전기저항율과 우수한 열적 안정성을 나타내었으며$ 600^{\circ}C$의 고온에서 장시간 열처리를 실시하여도 전기저항율이나 우선 배향성의 변화, 박막내 미세 결함 및 열적응집현상 등이 발생되지 않았다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.951-954
• /
• 2004

본 논문에서는 DLC(Diamond-like Carbon) 박막과 기판 사이에 금속층을 포함하는 DLC 박막의 기계적 특성을 분석하였다. 금속층은 sputtering법을 사용하고, DLC 박막은 PECVD법을 사용하여 각각 중착하였다. 티타늄(Ti), 니켄(Ni), 크롬(Cr)을 각 중간 금속층으로 사용한 후 DLC 박막과 실리콘(Si) 기판 간의 기계적 특성을 분석하였다. 각 막의 두께는 FE-SEM으로 확인하였고, DLC 박막의 구조 평가는 Raman spectrometer를 사용하여 분석하였으며, 각 금속층과 DLC 박막의 표면 상태는 AFM을 이용하여 확인하였다. XRD 분석을 통하여 박막의 격자분석을 하였고, SIMS(secondary ion mass spectrometry) 분석을 통하여 DLC 박막의 depth Profile을 확인하였다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.46 no.3
• /
• pp.530-544
• /
• 2022

Titanium exhibits substantial corrosion resistance, strength, and ductility, with a specific gravity of approximately 4.5 and a melting point of approximately 1800℃. It is currently used in aircraft parts and space development. This study considered the thermal characteristics, stealth effects of infrared thermal imaging cameras, electromagnetic shielding, and electrical conductivity of Ti-sputtered materials. Base materials of different densities and types were treated using titanium sputtering. Infrared thermal imaging showed a better stealth effect when the titanium layer was directed toward the outside. The film sample presented a better stealth effect than the fabrics did. In each of the samples subjected to titanium sputtering, when the titanium layer was directed outward, the untreated sample or exposed titanium layer showed surface temperatures lower than those of the samples with the titanium layer oriented toward the heat source. Additionally, after the titanium sputtering treatment, the films conducted electricity (low resistance) better than the fabrics did. All titanium-sputtered specimens presented reduced electromagnetic wave transmission and significantly reduced infrared transmission. These results are expected to apply to military uniforms (soldiers' protective clothing to gain the upper hand on the battlefield), medical sensors, multifunctional intelligent textiles and etc.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.421-428
• /
• 2001

New WC-CrN superlattice film was deposited on Si substrate (500$\mu\textrm{m}$) using cathodic arc ion plating system. The microstructure and mechanical properties of the film depend on the superlattice period (λ). In the X-ray diffraction analysis (XRD), preferred orientation of microstructure was changed according to various superlattice periods(λ). During the Transmission Electron Microscope analysis (TEM), microstructure and superlattice period (λ) of the WC - CrN superlattice film was confirmed. Hardness and adhesion of the deposited film was evaluated by nanoindentation test and scratch test, respectively. As a result of nanoindentation test, the hardness of WC - CrN superlattice film was gained about 40GPa at superlattice period (λ) with 7nm. Also residual stress with various superlattice period (λ) was measured on Si wafer (100$\mu\textrm{m}$) by conventional beam-bending technique. The residual stress of the film was reduced to a value of 0.2 GPa by introducing Ti - WC buffer layers periodically with a thickness ratio ($t_{buffer}$/$t_{buffer+superlattice}$ ). To the end, for the evaluation of oxidation resistance at the elevated temperature, CrN single layer and WC - CrN superlattice films with various superlattice periods on SKD61 substrate was measured and compared with the oxidation resistance.