• The Journal of the Petrological Society of Korea
• /
• v.28 no.3
• /
• pp.157-169
• /
• 2019

Pseudotachylytes, produced by frictional heating during seismic slip, provide information that is critical to understanding the physics of earthquakes. We report the results of occurrence, structural characteristics, scanning electron microscopic observation and geochemical analysis of pseudotachylytes, which is presumed to have formed after the Late Cretaceous in outcrops of the Paleoproterozoic granitic gneiss on the Bulil waterfall of the Jirisan area, Yeongnam massif, Korea. Fault rocks, which are the products of brittle deformation under the same shear stress regime in the study area, are classified as pseudotachylyte and foliated cataclasite. The occurrences of pseudotachylyte identified on the basis of thickness and morphology are fault vein-type and injection vein-type pseudotachylyte. A number of fault vein-type pseudotachylytes occur as thin (as thick as 2 cm) layers generated on the fault plane, and are cutting general foliation and sheared foliation developed in granitic gneiss. Smaller injection vein-type pseudotachylytes are found along the fault vein-type pseudotachylytes, and appear in a variety of shapes based on field occurrence and vein geometry. At a first glance fault vein-type seudotachylyte looks like a mafic vein, but it has a chemical composition almost identical to the wall rock of granitic gneiss. Also, it has many subrounded clasts which consist predominantly of quartz, feldspar, biotite and secondary minerals including clay minerals, calcite and glassy materials. Embayed clasts, phenocryst with reaction rim, oxide droplets, amygdules, and flow structures are also observed. All of these evidences indicate the pseudotachylyte formed due to frictional melting of the wall rock minerals during fault slip related to strong seismic faulting events in the shallow depth of low temperature-low pressure. Further studies will be conducted to determine the age and mechanical aspect of the pseudotachylyte formation.

• Korean Journal of Heritage: History & Science
• /
• v.39
• /
• pp.243-280
• /
• 2006

At the Bujang-ri Site, Seosan, South Chungcheong Province, around 220 archaeological features, including semi-subterranean houses and pits of Bronze Age and semi-subterranean houses, pits, and burials of Baekje period had been identified and investigated. In Particular, mound burials No. 5 of 13 of Baekje mound burials yielding a gilt-bronze cap along with other valuable artifacts drew international scholarly attention. The gilt-bronze cap from the mound burial No. 5 is a significant archaeological data not only in the study of Baekje archaeology but also in the study of international affairs and exchange at that time. At the time of exposure, the gilt-bronze cap was already broken into a number of pieces and seriously damaged by corrosion, and hardening and urethane foam were necessary in the process of collecting its pieces. Ahead of main conservational treatments on cap, X-ray photograph and CT(computerizes tomography) were taken in order to examine interior structure of the cap and to decide appropriate treatments. In the five layers identified in the profile of cap, a textile layer was set between a metal and a layerof bark of paper birch for avoiding direct contact of the metal and the bark of paper birch. Analyses were executed for examining textile layer and a layer of fibroid material. According to microscopic analysis, while the textile layer consisted of the simplest plain fabric with one fold among three kinds of textile structures, the layer of fibroid material was mixed with two or three kinds of fibers. A comparative analysis with standard sample using FT-IR (Fourier Transform Infrared Spectroscopy) announced that both textiles and fabrics were hemp. Analysis of kind of the paper birch resulted in barks of paper birch with 15 fold. A metallographic microscope, SEM, and WDS were used for the analysis of microscopic structures of plated metal pieces. While amalgam plating was treated as a plating method, the thickness of the plated layer, a barometer of plating technique, was ranged from $1.72{\mu}m$ to $8.67{\mu}m$. The degree of purity of gold (Au) used in plating was 98% in average, and less than 1% of silver (Ag) was included.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.428-434
• /
• 2019

Many countries have interested animal welfare. Similarly, domestic people have concern for the welfare from companion animals to livestock. Environmental enrichments (EE) are tool to enforce the welfare, however, research with sows is limited. Therefore, this study was investigate to effects of environmental enrichments on performance and behavior properties of gestating sows. A total of 30 pregnant sows (Landrace) were assigned into three treatments that control, T1 (plastic device) and T2 (Rice straw). Period of trial was from Mar. 03. 18. to Mary 19. 18. The EE were allotted to center of experimental pen ($11.6{\times}6.0m$). Body weight (BW), backfat thickness (BF) and cortisol were identified at experimental initial or end date. Behavior was recorded during 24 hours on days 91 of gestation, and then analyzed the patterns. BF was reduced (15.73 vs. 16.56 mm; p>0.05) in T1 than control, but Ending BW, total litter size and alive piglets did not differ. Born dead piglets showed lower tendency (1.00 and 0.63 vs. 1.50 heads; p>0.05) in T1 and T2 than control. Similarly, the enrichments declined farrowing mortality (C, 8.68%; T1, 6.86%; T2, 3.40%; p>0.05). Cortisol was not differed among treatments. In the behavior characteristics, eating showed lower (1.81 vs. 9.68 and 6.99%; p<0.05) in T2 than control and T1. Furthermore, playing or digging were only observed (0.33 and 2.10%; p<0.05) in T1 and T2, respectively, whereas rubbing (0.91%, p<0.05) only showed in the control. These results suggest that the provision of EE would be not negatively affected the performance of the gestating sows and could be led to improvement of the livestock welfare.

• Korean Journal of Plant Resources
• /
• v.32 no.2
• /
• pp.160-169
• /
• 2019

The this study was carried out to investigate the growth characteristics of wild-simulated ginseng by direct seeding and transplanting cultivation for develop standard cultivation techniques of wild-simulated ginseng. Bonghwa experimental field were confirm to be suitable location environment for cultivation of wild-simulated ginseng. As a result of this study, the germination rate of wild-simulated ginseng was significantly highest when seed size was over 6.5 mm in the spot seeding cultivation. In the case of transplanting, survival rate was significantly increased when the diameter of root was over 10 mm, planting distance was 7 cm, and the thickness of soil covering was less then 2 cm. The result of growth characteristics of wild-simulated ginseng by cultivation type, growth of stem in spot seeding cultivation was showed significantly increased when seed size over 6 mm, seeding number was 3 grains, and the seeding distance was less then 5 cm. Strip seeding cultivation was showed significantly increased in stem and root growth when seeding distance was 30 cm grains and quantity of seeding was less then 23 g. In the case of transplanting cultivation, it's was showed significantly increased in stem growth when diameter of root was over then 10 mm and direction of rhizome was top and bottom. The results of this study was that to clearly establish the techniques of cultivation of managements and it's will be suggest contribute to the industrial activation of wild-simulated ginseng.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.2
• /
• pp.110-117
• /
• 2019

Purpose: This study was to evaluate the wear resistance of 3D printed, milled, and conventionally cured provisional resin materials. Materials and methods: Four types of resin materials made with different methods were examined: Stereolithography apparatus (SLA) 3D printed resin (S3P), digital light processing (DLP) 3D printed resin (D3P), milled resin (MIL), conventionally self-cured resin (CON). In the 3D printed resin specimens, the build orientation and layer thickness were set to $0^{\circ}$ and $100{\mu}m$, respectively. The specimens were tested in a 2-axis chewing simulator with the steatite as the antagonist under thermocycling condition (5 kg, 30,000 cycles, 0.8 Hz, $5^{\circ}C/55^{\circ}C$). Wear losses of the specimens were calculated using CAD software and scanning electron microscope (SEM) was used to investigate wear surface of the specimens. Statistical significance was determined using One-way ANOVA and Dunnett T3 analysis (${\alpha}=.05$). Results: Wear losses of the S3P, D3P, and MIL groups significantly smaller than those of the CON group (P < .05). There was no significant difference among S3P, D3P, and MIL group (P > .05). In the SEM observations, in the S3P and D3P groups, vertical cracks were observed in the sliding direction of the antagonist. In the MIL group, there was an overall uniform wear surface, whereas in the CON group, a distinct wear track and numerous bubbles were observed. Conclusion: Within the limits of this study, provisional resin materials made with 3D printing show adequate wear resistance for applications in dentistry.

• Journal of the Korean Society of Radiology
• /
• v.79 no.5
• /
• pp.254-258
• /
• 2018

Purpose: Establishment of an appropriate protocol for breast magnetic resonance imaging (MRI) in the study of image quality standards to enhance the effectiveness of medical image information exchange, which is part of the construction and activation of clinical information exchange for healthcare informatization. Materials and Methods: The recommended protocols of breast and MRI scans were reviewed and the questionnaire was prepared by a responsible researcher. Then, a panel of 9 breast dedicated radiologists was set up in Korea. The expert panel conducted a total of three Delphi agreements to draw up a consensus on the breast MRI protocol. Results: The agreed breast MRI recommendation protocol is a 1.5 Tesla or higher device that acquires images with prone position using a breast dedicated coil and includes T2-weighted and pre-contrast T1-weighted images. Contrast enhancement images are acquired at least two times, and include 60-120 seconds between images and after 4 minutes. The contrast enhancement T1-weighted image should be less than 3 mm in thickness, less than 120 seconds in temporal resolution, and less than $1.5mm^2$ in-plane pixel resolution. Conclusion: The Delphi agreement of the domestic breast imaging specialist group has established the recommendation protocol of the effective breast MRI.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.5
• /
• pp.399-415
• /
• 2021

This study was conducted to suggest the optimal periods for planting and felling Larix kaempferi tree by monitoring its cambial activity period. In addition, the heat summation to induce the cambial activity of Larix kaempferi was investigated. The study sites were at Mt. Worak and Mt. Midong. After selecting 5 trees at Mt. Worak and Mt. Midong, the cambium samples were collected using a mini trephor with 2 mm diameter from April 7 to October 6, 2017 at Mt. Worak, and from April 7 to September 29, 2017 at Mt. Midong. After the collected cambium samples were embedded in PEG2000, transverse thin sections with a thickness of 10 to 15 ㎛ were prepared using a microtome. One Larix kaempferi sample from each site, Mt. Worak and Mt. Midong, in which the accurate monitoring of cambial activity was impossible due to the formation of traumatic resin canal, was excluded from the study. The observation of the initiation date of cambial activity under a light microscopy revealed that 2 specimens from Mt. Worak and 3 from Mt. Midong showed the initiation on April 28. The remaining 2 specimens of Mt. Worak and 1 specimen of Mt. Midong were initiated on May 4, which was a week later than the others. The heat summation that induced the initiation of cambial activity was 196.4-271.8 at Mt. Worak and 204.7-277.3 at Mt. Midong, which was similar. The termination of cambial activity occurred between August 4 and 25 at Mt. Worak, and between August 4 and September 1 at Mt. Midong. Based on the above results, it was found that the optimal planting period for Larix kaempferi in Mt. Worak and Mt. Midong was before April, about a month before the cambium activity, and the felling period was from October when the cambial activity was completely terminated.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.3
• /
• pp.242-261
• /
• 2021

Sangjeong was a sculptor-monk who was active in the mid-to-late 18th Century, and the current study established the overall chronology of Sangjeong's Buddhist statues and their styles based on the six sculptures of Sangjeong already known and the Wooden Seated Buddha of 1767 in Songgyesa Temple, Geochang, which was found to be his last work. All of the Buddhist statues of Sangjeong have commonalities in terms of the appearance of the ears, wrinkles on clothing on the upper and lower body, position of hands, and expression of the lower body. The expression of the lower body, in particular, is classified into three types: Type A, where the clothing drapes through the lotus leaves on the bottom; Type B, with an 'S-shaped' drape over the lower body but no lotus leaves or pedestal; and Type C, with the Buddha and pedestal as a single unit, and the clothing draping through the lotus leaves on the pedestal. It appears that Sangjeong faithfully succeeded the style of Taewon, who was his only instructor for sculpture. This is verified based on the records of his participation in the creation of the Wooden Seated Sakyamuni Buddha Triad and Statue of Arhat in Bongeunsa Temple, Seoul, as the third sculptor-monk out of twelve sculptor-monks, and the reflection of the S-shaped drape on the lower body found on the statue of Buddha in Bongeunsa Temple on all of the statues created by Sangjeong. Not only that, but it was assumed that the expression of the pedestal and hair was also inherited by Sangjeong from Taewon and Jinyeol, who was a sculptor-monk from the early 18th Century. The work of Sangjeong and Taewon showed differences in the volume and thickness of statues, strength of unevenness on the wrinkles of clothing, drapes on the right side of chest, and details of the ears. The current study identified the original styles of each individual sculptor and attempted to categorize the fourteen pieces of ten Buddhist statues reflecting the styles of Sangjeong into Sangjeong-style or Taewon-style.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.3
• /
• pp.65-75
• /
• 2021

Coin cell is a basic testing platform for battery research, discovering new materials and concepts, and contributing to fundamental research on next-generation batteries. Li metal batteries (LMBs) are promising since a high energy density (~500 Wh kg^-1) is deliverable far beyond Li-ion. However, Li dendrite-triggered volume fluctuation and high surface cause severe deterioration of performance. Given that such drawbacks are strongly dependent on the cell parameters and structure, such as the amount of electrolyte, Li thickness, and internal pressure, reliable Li metal coin cell testing is challenging. For the LMB-specialized coin cell testing platform, this study suggests the optimal coin cell structure that secures performance and reproducibility of LMBs under stringent conditions, such as lean electrolyte, high mass loading of NMC cathode, and thinner Li use. By controlling the cathode/anode (C/A) area ratio closer to 1.0, the inactive space was minimized, mitigating the cell degradation. The quantification and imaging of inner cell pressure elucidated that the uniformity of the pressure is a crucial matter to improving performance reliability. The LMB coin cells exhibit better cycling retention and reproducibility under higher (0.6 MPa → 2.13 MPa) and uniform (standard deviation: 0.43 → 0.16) stack pressure through the changes in internal parts and introducing a flexible polymer (PDMS) film.

• Journal of Korean Society of Forest Science
• /
• v.100 no.3
• /
• pp.432-440
• /
• 2011

The objective of this study was to investigate growth and fruiting characteristics (e.g., nut qualities) of chestnut (Castanea cerenata) after applying various fertilizer treatments at the cultivation site in Suncheon. Fertilizer treatments were designed as follow: liquid fertilizer, chemical fertilizer, organic fertilizer, and control. Both liquid and chemical fertilizer treatments provided the best growth in height and basal diameter. In addition, these two treatments were very effective for crown width of the trees between both east-west and north-south orientation. The liquid fertilizer treatment was effective on total length of the fruiting branch and length of the bearing to terminate part. Both liquid and chemical fertilizer treatments produced the longest length of basal to bearing part compared to the other two treatments. The liquid fertilizer treatment showed the most thickened basal diameter of the fruiting branch and the greatest diameter of above and below the bearing burr part. Elongation Index of the fruiting branch (EI) was the highest with liquid fertilizer treatment and the remaining four indices (Production Index of fruiting branch, PI; Ratio of Diameter between below and above bearing burr part, RD; Growth Index of fruiting branch diameter, GI; Thickness Index of fruiting branch or dormant branch, TI) were the highest with the chemical fertilizer treatment. Total number of produced branch per fruiting mother branch and number of small and weak branches per fruiting mother branch were highest on the control and liquid fertilizer treatment; however, all treatments produced similar numbers. The chemical and organic fertilizer treatments produced a high number of fruiting branches per fruiting mother branch, while organic and liquid fertilizer treatments produced a high number of burr per fruiting branch. The rate of commercializing on the basis of nut weight and quantity was higher on control (87.5%) than chemical fertilizer treatment (84.6%); however, the rate was even lower on liquid fertilizer treatment (84.3%) and organic fertilizer treatment (82.7%). The liquid fertilizer treatment showed the highest average of nut weight, while chemical fertilizer treatment showed the highest average number of fruiting burr. There was no significant difference in average number of normal nuts per burr among treatments. The yield per tree was high on chemical (8.2 kg) and liquid (8.0 kg) fertilizer treatments, but there was no significant difference among treatments. In the rate of nut grade on the basis of nut weight and quantity, the liquid fertilizer treatment, 43.5% and 34.3% more than large nut respectively, produced higher value chestnuts compared to other treatments.