• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.80-89
• /
• 1996

Fatigue life of a notched shaft was evaluated in order to estimate the durability and integrity of the notched shaft in design stage. Cumulative fatigue dama- ge analysis was performed using local strain approach based on the assumption that the fatigue life of a notched component is approximately same as that of a smooth specimen is subjected to the same strain at the notched component. In this paper, shafts with different notch root radius of 1, 2㎜ resulting in different values of stress concentration factors were tested under||rotating bending fatigue loading condition. Theoretical stress concentration factor for each notch type was calculated using finite element method. Fatigue life prediction program, FALIPS, written in C language was developed using the strain-life curve, and the local strain approach integrating Neuber's rule, cyclic stress-strain, and hysteresis loop equations. The fatigue life evaluated using the fatigue notch factor obtained from the experimentally determined fatigue strength showed very large scattering with nonconservatism, but the fatigue notch factors derived from the stress concentration factors and Peterson's equation reduced the considerablely accurate fatigue life evaluation within a factor of three.

• 한국해양공학회지
• /
• 제16권1호
• /
• pp.46-51
• /
• 2002

Fatigue life estimation by the theoretical stress concentration factors are, in general, considerably different from test results. And in calculating stress concentration factor, it is very difficult to consider actual geometry and material property which are the notch shapes, imperfections or defects of materials such as porosities inclusions and casting defects, etc. Therefore, the paper deals with the experimental method to find out the more exact stress concentration factors by measuring the strain distributions on each specimen by 3D-ESPI(Electronic Speckle Pattern Interferometry) System. Then the fatigue lives are compared between theoretical calculations using stress concentration factors determined by 3D-ESPI system and fatigue test results.

• 국제초고층학회논문집
• /
• 제9권4호
• /
• pp.325-334
• /
• 2020

This paper aims to evaluate the interfacial stress concentrations on connection between vertical through-plate and H-beam in CFT column. Full-scale experiments were performed on three specimens with varying thickness of the vertical through-plate to investigate the interfacial stress concentration factor in the connections. The specimens underwent brittle failure at the location where the steel beam is connected to the vertical through-plate before the steel beam reached its plastic moment. The strain data of the part were analyzed, and the sectional analyses were conducted to determine appropriate residual stress models. In addition, the stress concentration factor was quantified by comparing the analytical local behavior in which the stress concentration is not reflected and the experimental data reflecting the stress concentration. The results showed that the maximum reduction of the stress concentration factor due to an increase in the thickness of the vertical through-plate is 50.3%.

• Journal of Mechanical Science and Technology
• /
• 제18권5호
• /
• pp.808-813
• /
• 2004

The stress analysis on orthotropic composite cylindrical shells with one circular or one elliptical cutout subjected to an axial force is carried out by using an analytical and experimental method. The composite cylindrical shell governing equation of the Donnell's type is applied to this study and all results are presented by the stress concentration factor. The stress concentration factor is defined as the ratio of the stress on the region around a cutout to the nominal stress of the shell. The stress concentration factor is classified into the circumferential stress concentration factors and the radial stress concentration factors due to the cylindrical coordinate of which the origin is the center of a cutout. The considered loading condition is only axial tension loading condition. In this study, thus, the maximum stress is induced on perpendicular region against axial direction, on the coordinate. Various cutout sizes are expressed using the radius ratio, (equation omitted), which is the radius of a cutout over one of the cylindrical shell. Experimental results are obtained using strain gages, which are attached around a cutout of the cylindrical shell. As the result from this study, the stress concentration around a cutout can be predicted by using the analytical method for an orthotropic composite cylindrical shell having a circular or an elliptical cutout.

• 비파괴검사학회지
• /
• 제26권5호
• /
• pp.329-335
• /
• 2006

기계구조물 설계시 파손이나 갑작스런 붕괴를 방지하기 위하여 응력집중을 실험적으로 측정해야 할 필요가 있다. 본 연구에서는 중앙에 원형구멍이 있는 외팔보 시편의 응력집중계수를 스트레인 게이지와 광탄성법으로 측정하였다. 스트레인 게이지법에서는 구멍 주위에 3개의 스트레인 게이지를 부착하여 측정된 값으로부터 외삽법을 사용하여 구멍에 인접한 지점에서 최대 변형률을 추정하였다. 광탄성법에서는 두 가지 측정법, 즉 배비넷-솔레일 보상법과 위상이동법을 이용하여 응력분포를 측정하였다. 스트레인 게이지와 광탄성법에 의한 측정값들을 서로 실험오차 이내로 근접하였다.

• 대한기계학회논문집
• /
• 제6권4호
• /
• pp.367-376
• /
• 1982

Stress concentration mainly occurs near holes and notches. Then local stress is larger than nominal stress. It is necessary that stress concentration phenomena are studied because it can act as a cause of fracture of material. In order to analyze fracture of material including holes, stress concentration factor and stress distribution must be studied more carefully. In this paper the stress concentration and distribution of a slotted plate is examined. Hardened 7:3 brass plate with 4 different slots including a circular hole is used. And ratios of slot length to its root radius are 1, 2, 3, 24, 4. The stress distribution is measured by using strain gages attached to the plate with variable width. And obtained experimental data are adjusted by using calibrated gage factor.

• 선박안전
• /
• 제12권
• /
• pp.36-43
• /
• 2003

Fatigue life estimation by the theoretical stress concentration factors are, in general, considerably different from test results. And in calculating stress concentration factor, it is very difficult to consider actual geometry and material property which are the notch shapes, imperfections or defects of materials such as porosities inclusions and casting defects, etc. Therefore, the paper deals with the experimental method to find out the more exact stress concentration factors by measuring the strain distributions on each specimen by 3D-ESPI(Electronic Speckle Pattern Interferometry) System. Then the fatigue lives are compared between theoretical calculations using stress concentration factors determined by 3D-ESPI system and fatigue test results

• 대한조선학회지
• /
• 제7권2호
• /
• pp.27-40
• /
• 1970

The distribution of stress and strain in elastic stages is investigated by the experiments of two dimensional photoelastic coating and Moire fringe method. Center block type and cover plate type of fillet welds are used as specimens in the test. The results are as follows. 1) Center block type gets less uniform stress distribution than cover plate type. And its stress concentration factor, especially at root, is larger than that at toe. 2) When main plate and cover plate closely contact and it cause friction, stress concentration decreases more than that in case of slit. That is because stress can be transmitted on the contact surface. 3) When slit is made, the outside of fillet gets more stress than the inside of it. 4) While the plastic strain distribution of center block type reaches the maximum at root and differs very slightly from that under lower loading, the plastic strain distribution of cover plate type is inclined to get the maximum at the outside of fillet rather than at root. 5) When the plastic strain value of cover plate type is compared with that of center block type at toe and root, the relations between the former and the latter shows root<toe and root>toe. 6) Because stress distribution becomes changed according to loading, fracture angle cannot be estimated by the peaks of elastic stress distribution. 7) The strain distribution just before fracture can be found by Moire fringe method.

• 한국해양공학회지
• /
• 제4권1호
• /
• pp.110-119
• /
• 1990

This study is concerned about the stress concentration factor measurement by photoelastic method, for the case of two circular holes arrangement in 3mm semi-infinite plate under tensile load, the ratio of those two circular holes diameter, the ratio of distance apart from circular holes to breadth and the two holes arrangement angle with loading direction were varied. Besides, the measured stress concentration by photoelastic method around one circular hole was compared with that by strain-gage method.

• 한국지반공학회논문집
• /
• 제18권5호
• /
• pp.133-141
• /
• 2002

암반파괴의 가장 큰 영향을 미치는 인장강도는 등방의 암석과 횡등방의 암석의 경우는 분명히 다를 것이다. 본 논문에서는 일축압축강도시험에서 횡등방 암석의 탄성정수를 구하고, 간접인장강도시험을 통하여 횡등방 암석의 인장강도와 인장파괴 거동을 분석하였다. 일축압축시험에서 구한 이방성 탄성정수와 간접인장강도시험에서 얻어진 변형률로 시료중앙의 응력집중계수를 구하여, 등방으로 가정하여 구한 인장강도 값과 이방성일때의 인장강도 값을 비교 분석하였다. 실험 결과 횡등방성 암석의 응력집중계수는 층리면의 각도에 따라서 등방재료의 응력집중계수와는 크거나 작은 값을 나타내었다. 횡등방 암석의 인장강도 산정시 등방의 응력집중계수를 사용하는 것은 층리면이 이루는 각도에 따라 인장강도의 과대 혹은 과소 평가됨을 알 수 있었다.