• Journal of the korean academy of Pediatric Dentistry
• /
• v.39 no.4
• /
• pp.383-388
• /
• 2012

The aim of this study was to compare the compressive strength and the surface microhardness of Beautifil flow (Shofu, Kyoto, Japan) with $Filtek^{TM}$ Z350, Z350XT (3M ESPE, USA). Fifteen specimens from each material were fabricated for testing. Compressive strength was measured by using a universal testing machine at a crosshead speed of 1 mm/min. Surface microhardness values were measured by using Vickers hardness tester under 4.9 N load and 10 seconds dwelling time. The compressive strength of Group 2 $Filtek^{TM}$ Z350XT shows the highest value as $218.7{\pm}18.4$ MPa and Group 1 $Filtek^{TM}$ Z350 was $205.5{\pm}27.1$ MPa. Group 3 Beautifil flow F00 was $176.5{\pm}30.3$ MPa, and Group 4 Beautifil flow F10 was $173.4{\pm}26.2$ MPa. The compressive strength of Group 2 is higher than Group 3 and 4 (p < 0.05). The surface microhardness of Group 2 $Filtek^{TM}$ Z350XT shows the highest value as $39.1{\pm}2.1$ and Group 4 Beautifil flow F10 was $27.9{\pm}1.8$. And Group 3 Beautifil flow F00 was $23.1{\pm}1.1$, Group 1 $Filtek^{TM}$ Z350 was $20.4{\pm}0.9$. There was a statistical significant difference in surface microhardness between all groups (p < 0.05). In conclusion, the compressive strength of giomer was below the level of flowable composite resin. However, the surface microhardness of giomer is comparable to that of flowable composite resin. Giomer would be the good alternative to composite resin, if there is improvement of the compressive strength of giomer.

• Restorative Dentistry and Endodontics
• /
• v.14 no.1
• /
• pp.41-56
• /
• 1989

The purpose of this study was to examine the effect of temperature dependence of the behavior on the physical properties of posterior composite resins. Three light cure posterior composite resins (Heliomolar, Litefil-P, and P-50) and one chemical cure posterior composite resin (Bisfil-II) were used as experimental materials. Composite resin was placed in a cylindrical brass mold (2.5 mm high and 6.5 mm inside diameter) that was rested on a glass plate. Another flat glass was placed on top of the mold, and the plate was tightly clamped together. After the mold had been filled with the light cure composite material, the top surface was cured for 30 seconds with a light source. Chemical cure resin specimens were made in the same manner as above. Three hundreds and twenty composite resin specimens were constructed from the four composite materials. One hundred and sixty specimens of them were placed in a heater at $50^{\circ}C$, $75^{\circ}C$, $100^{\circ}C$, $125^{\circ}C$, $150^{\circ}C$, $175^{\circ}C$ and $200^{\circ}C$ for 5 minutes or 10 minutes respectively before compressive strengths were measured. Another one hundred and sixty specimens were tested for the diametral tensile strengths in the same way as above. They were randomly divided into eight groups according to the mode of heating methods as follows and stored in distilled water at $37^{\circ}C$ for 24 hours. Group $37^{\circ}C$ - specimens were stored at $37^{\circ}C$ in distilled water for 24 hours. Group $50^{\circ}C$ - specimens were heated at $50^{\circ}C$ after curing. Group $75^{\circ}C$ - specimens were heated at $75^{\circ}C$ after curing. Group $100^{\circ}C$ - specimens were heated at $100^{\circ}C$ after curing. Group $125^{\circ}C$ - specimens were heated at $125^{\circ}C$ after curing. Group $150^{\circ}C$ - specimens were heated at $150^{\circ}C$ after curing. Group $175^{\circ}C$ - specimens were heated at $175^{\circ}C$ after curing. Group $200^{\circ}C$ - specimens were heated at $200^{\circ}C$ after curing. Twenty specimens of each of four composite resins were respectively made by insertion of materials into same mold for examining the dimensional changes between before and after heating. The final eighty specimens were stored in distilled water at $37^{\circ}C$ for 24 hours before testing the dimensional changes. Compressive and diametral tensile strengths were measured crosshead speed 1mm/minute and 500Kg in full scale with a mechanical testing machine (DLC 500 Type, Shimadzu Co., Japan). Dimensional changes were determined by measuring the diametral changes of eighty specimens with micrometer (Mitutoyo Co., Japan). Results were as follows: 1. Diametral tensile strengths of specimens in all groups were increased with time heated compared with control group except for that in group $50^{\circ}C$ and the maximum diametral tensile strength was appeared in the specimen of Litefil-P heated for 10 minutes at $100^{\circ}C$. In heliomolar and P-50, it could be seen in the specimen heated for 10 minutes at $150^{\circ}C$, but in Bisfil-II, it could be found in the specimen heated for 5 minutes at $150^{\circ}C$. 2. Compressive strengths of specimens in all groups was tended to be also increased with time heated but that in group $50^{\circ}C$ and the maximum compressive strengths were showed in the same specimens conditioned as the diametral tensile strengths of four composite materials tested. 3. In Heliomolar, Litefil-P, and Bisfil-II, it was decreased in diameters of resin specimens between before heating and increased in diameters of resin specimens after storing in distilled water, but it was not in P-50. 4. There is little difference in diametral tensile strengths, compressive strengths, and dimensional changes followed by heating the resin specimens for 5 minutes and 10 minutes, but there is no statistical significances.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.2
• /
• pp.119-126
• /
• 2012

State of problem: Cement-retained implant-supported prostheses are routinely used in dentistry. The use of high strength cements has become more popular with the increasing confidence in the stability of the implant-abutment screw connection and the high survival rates of osseointegrated implants. No clinical data on retention of metal copings using CAD/CAM. To evaluate retention of metal copings using CAD/CAM system bonded to short titanium abutment with four different cements and compare retentive strength of metal copings with sandblasting or without sandblasting before cementation. Forty titanium abutment blocks were fabricated and divided into 4 groups of 10 samples each. Forty metal copings with occlusal hole to allow for retention testing were fabricated using CAD/CAM technology. The four cements were Fujicem(Fuji, Japan), Maxcem Elite(Kerr, USA), Panavia F2.0(Kurarary, Japan) and Superbond C&B(Sunmedical, Japan). The copings were cemented on the titanium abutment according to manufacture's recommendation. All samples were stored for 24h at 37oC in 100% humidity and tested for retention using universal testing machine(Instron) at a crosshead speed of 1.0mm/min. Force at retentive failure was recorded in Newton. The mode of failure was also recorded. Means and standard deviations of loads at failure were analyzed using ANOVA and Paired t-test. Statistical significance was set at P<0.05. Panavia F2.0 provided significantly higher retentive strength than Fujicem, Maxcem Elite(P<0.05). Sandblasting significantly increased bond strength(P<0.05). The mode of failure was cement remaining principally on metal copings. Within the limitation of this study, Panavia F2.0 showed significantly stronger retentive strength than Fujicem, Maxcem Elite(p<0.05). The Ranking order of the cements to retain the copings was Panavia F2.0, Fujicem = Maxcem Elite. Sandblasting significantly increased bond strength(P<0.05). The retentive strength of metal copings on implant abutment were influenced by surface roughness and type of cements.

• Journal of Korean Academy of Nursing
• /
• v.29 no.1
• /
• pp.161-173
• /
• 1999

The purpose of this study was to develope and test the structural model for quality of life in women having hysterectomies. A hypothetical model was constructed on the basis of previous studies and a review of literature. The conceptual framework was built around eight constructs. Exogenous variables included in this model were marital intimacy, importance of uterus, professional support, positive coping behavior and pre-operative symptoms. Endogenous variables were spouse's support, sense of loss and quality of life. Empirical data for testing the hypothetical model was collected using a self-report questionnare from 203 women having hysterectomies at the outpatient clinics of four general hospitals and a mail survey in Pusan City. The Data was collected from December, 1997 to January, 1998. Reliability of the eight instruments was tested with Cronbach's alpha which ranged from 0.639-0.915. For the data analysis, SPSS 7.5 WIN Program and LISREL 8.12 WIN Program were used for descriptive statistics and covariance structural analysis. The results of covariance structure analysis were as follows : 1. Hypothetical model showed a good fit with the empirical data. ［$\chi$$^2$＝6.93(df＝5, P＝.23), GFI＝.99, AGFI＝.94, RMSR＝.019, NNFI＝.97, NFI＝.98, CN＝440, standardized residuals(-2.14-2.10)］ 2. For the parsimony of model, a modified model was constructed by deleting 3 paths and adding 1 path according to the criteria of statistical significance and meaning. 3. The modified model also showed a good fit with the data. ［$\chi$$^2$＝5.26(df＝7, P＝.63), GFI＝.99, AGFI＝.97, RMSR＝.014, NNFI＝1.02, NFI＝.99, CN＝710, standardized residuals(-1.46-1.70)］ Results of the testing of the hypothesis were as follows : 1. Marital intimacy(${\gamma}$11＝.78, t＝14.37) and professional support(${\gamma}$13＝.12, t＝2.12) had a significant direct effect on the spouse's support. 2. Pre-operative symptoms(${\gamma}$25＝.32, t＝3.12), importance of uterus(${\gamma}$22＝.20, t＝2.61) and spouse's support($\beta$2l＝-.19, t＝-2.43) had a significant direct effect on the sense of loss. 3. Sense of loss($\beta$32＝-.66, t＝-9.83) had a direct effect on the quality of life. Marital intimacy had a direct(${\gamma}$31＝.19, t＝3.33), indirect(${\gamma}$31＝.14, t＝2.52) and total effect(${\gamma}$31＝.25, t＝4.41) on the quality of life. Professional support had a direct effect(${\gamma}$33＝.11, t＝2.07) and total effect(${\gamma}$33＝.13, t＝2.31) on the quality of life. The direct effect of pre-operative symptoms(${\gamma}$35＝-.36, t＝4.02) and positive coping behavior(${\gamma}$34＝.15, t＝2.06) had the insignificant effect on the quality of life while, due to the idirect effect these variables had overall significant effect on the quality of life. The results of this study showed that the sense of loss had the most significant direct effect on the quality of life. Marital intimacy, pre -operative symptoms and spouse's support had a significant direct effect on this sense of loss. These four variables, the sense of loss, marital intimacy, pre-operative symptoms and spouse's support, were identified as relatively important variables. The results of this study suggested that there is needed to determine if nursing intervention would alleviate this sense of loss and promote a greater quality of life in women who have had hysterectomies.

• Journal of the HCI Society of Korea
• /
• v.8 no.1
• /
• pp.1-9
• /
• 2013

This is to develop a new way of testing self-esteem by adopting DAP(Draw a Person) test and to make a platform to digitalize it for young people in the adolescent stage. This approach is to get high effectiveness of the self-esteem measurement using DAP test, including some personal inner situations which can be easily missed in the large statistical analysis. The other objective of this study is digitalize to recover limits of DAP test in the subjective rating standard. It is based on the distribution of the figure drawing expressed numerically by the anxiety index of Handler. For these two examinations, we made experiment through 4 stages with second grade middle school 73 students from July 30th to October 31th in 2009 during 4 months. Firstly, we executed 'Self Values Test' for all 73 people, and divided them into two groups; one is high self-esteem group of 36 people, the other is low self-esteem group of 37 people. Secondly, we regrouped them following D (Depression), Pd (Psychopathic Deviate), Sc (Schizophrenia) scales of MMPI; one is high self-esteem group of 7 people, the other is low self-esteem group of 13 people. Thirdly, we conducted DAP test separately for these 20 people. We intended to verify necessity and appropriateness of direction of 'Digitalizing Measurement System' by comparing and analyzing relation between DAP and Self-esteem following evaluation criteria which has similarity in 3 tests, after executing DAP to reflect peculiarity of adolescents sufficiently. We compared and analyzed result abstracted by sampling DAP test of two groups; One is high self-esteem group of 2 people, the other is low self-esteem group of 2 people; to confirm whether we can improve limitation that original psychological testing has by comparing mutual reliance of measurement test. Finally, with DAP test gained from correlations between self-esteem and melancholia following as above-mentioned steps, we discovered possibility of realization to get a concrete and individual criteria of evaluation based on Expert System as a way of enhancing accessibility in quantitative manner. 'Digitalizing Measurement Program' of DAP test suggested in this study promote results' reliability based on existing tests and measurement.

• The Korean Nurse
• /
• v.31 no.3
• /
• pp.76-87
• /
• 1992

The purposes of study was: 1. To identify the direction and scope of research activities in Korean Nursing. 2. To discuss the unique problems present in Korea that warrant nursing research. 3. To delineate the factors that facilitate and/or hinder nursing research in Korea. This study was conducted at six colleges of nursing in Korea. The schools which were selected had doctoral programs at the time, the data were collected in 1990. Four of the schools were located in the metropolitan area of the capital city, Seoul, and two were in two other cities similar in size. The total population of the study was 283 nurses. The instrument for the research was the English version of Research Profile Questionnaire which was translated into Korean by the researchers and was validated in its translation by two professors. A pretest procedure was done before the data collection process. Of the population of 283, 210 subjects received the questionnaire and 150 subjects responded(71.4%). Excluding incomplete questionnaires, 141 questionnaires were utilized for data analysis. Data were analyzed using descriptive statistics. Responses to open-ended questions were content analyzed for themes and categories. Results of the study were as follows : Respondents currently , involved in nursing research numbered 108(76.6%), but 33(23.4%) did not have any research experience. The inexperienced respondenLs tended to be younger than the experienced subjects and most( 60.6%) were employed in hospitals, while 82.4 percent of the experienced nurses were employed in nursing schools. Among the respondents with research experience, 68.5 percent were involved in one to three projects and 31.5 percent were engaged in four or more projects. The experienced nurses indicated that nursing research in Korea is active. On the other hand, the responses of the inexperienced were that nursing research is not active. The most frequently selected research subjects were patients(76.9%, 83 respondents) followed by nurses, healthy persons and nursing students. The relatively high percentage of healthy persons as study subjects, could be explained as a concern of nurses for healthy persons as well as for ill patients. The aforememioned literature review showed a dramatic change in the kinds of study subjects; approximately 33 percent were patients but 25 percent were healthy subjects of various ages. The hospital was the prevailing research setting(67.6%) but at the same time various community settings were used. This is a changing phenomena in nursing research of Korea. Current research designed to build on previous studies amounted to 75 percent; about 39.8 percem were theory and hypothesis generated. Over 65 recommended additional research focusing on hypothesis-testing 0:' theory building. The previously quoted literature review found that only 4.0 percent of the study quescions were developed from a theoretical framework. The most frequently listed current major focus of nursmg research was stress and adaptation. Patients with cancer, pain, social support and care of the elderly were the next most frequently reported. These concerns may reflect problems associated with a technological and industrializing societyl. The most frequently identified problem was lack of clinical research. The need for replication research and research that contributes to the accumulation of nursing knowledge were found to be rare in Korean research. A need for theory testing and theory construction research was also identified. Although advanced statistical methods were often utilized in nursing research, the results were frequently considered by the interviewers not to be applicable in practice, and readers had difficulty in comprehending the findings. Even though the number of clinical nurses involved in research is increasing, it is still considered inadequate. Among 108 respondents, 83(76.9%) gave lack of time as a barrier to conducting nursing research. Over fifty percent of the respondents reported lack of funding or, personally, low confidence in research skills as barriers. The respondents offered 183 suggestions for future emphasis in nursing research. Among the 51 areas of emphasis, clinical research received the highest number and nursing intervention was next. The findings suggested that nursing research should be based on theory, be related to practice and relevant to the situation of a unique Korean culture.

• The korean journal of orthodontics
• /
• v.28 no.5 s.70
• /
• pp.803-812
• /
• 1998

The purpose of this study was to evaluate the shear bond strength and failure mode of ceramic brackets according to the surface treatment of porcelain. Sixty Porcelain samples were randomly divided into six groups of ten samples. Then they were treated as follows: Group 1(silane only), Group 2(etching+silane), Group 3(stone+silane), Group 4(sandblasting+silane), Group 5(stone +etching+silane), Group 6(sandblasting+etching+silane) After surface treatment of porcelain, sixty Transcend 6000 brackets were bonded to the prepared porcelain surface and they were stored in $37^{\circ}C$ saline for 24 hours. An Instron universal testing machine was used to test the shear bond strength of ceramic brackets to porcelain. After debonding, bases of ceramic brackets and porcelain surfaces were examined under scanning electron microscope(SEM) to determine failure mode. Statistical analysis of the data was carried out with one-way ANOVA and Duncan's multiple range test. The results were as follows : 1. The shear bond strength of surface-treated groups 2 to 6 was higher than that of only silane-treated group 1, and there was statistical significance. (P<0.05) 2. There was no significant difference among the groups 3 to 6. (P>0.05) 3. The shear bond strength of etching-surface treated group 2 was significantly lower than those of sandblasting-surface treated group 4, complex surface treated group 5 and group 6. 4. According to the scanning electromicroscopic images, the surface roughness of sandblasting-surface treated group 4 was less than those of the group 5 and 6, but there was no significant difference in the shear bond strength. (P>0.05) As a conclusion we can have a clinically adequate bond strength when an application of silane is done after the treatment of porcelain surface with more than one way to bond ceramic bracket on the porcelain. Also, it is considered that the sandblasting and application of silane is effective for the simplication and convenience of the treatment.

• Asia pacific journal of information systems
• /
• v.17 no.4
• /
• pp.187-206
• /
• 2007

The development of computer and information technology has been combined with the information superhighway internet infrastructure, so information widely spreads not only in special fields but also in the daily lives of people. Information ubiquity influences the traditional way of transaction, and leads a new E-commerce which distinguishes from the existing E-commerce. Not only goods as physical but also service as non-physical come into E-commerce. As the scale of E-Commerce is being enlarged as well. It keeps people from finding information they want. Recommender systems are now becoming the main tools for E-Commerce to mitigate the information overload. Recommender systems can be defined as systems for suggesting some Items(goods or service) considering customers' interests or tastes. They are being used by E-commerce web sites to suggest products to their customers who want to find something for them and to provide them with information to help them decide which to purchase. There are several approaches of recommending goods to customer in recommender system but in this study, the main subject is focused on collaborative filtering technique. This study presents a possibility of pre-evaluation for the prediction performance of customer's preference in collaborative filtering before the process of customer's preference prediction. Pre-evaluation for the prediction performance of each customer having low performance is classified by using the statistical features of ratings rated by each customer is conducted before the prediction process. In this study, MovieLens 100K dataset is used to analyze the accuracy of classification. The classification criteria are set by using the training sets divided 80% from the 100K dataset. In the process of classification, the customers are divided into two groups, classified group and non classified group. To compare the prediction performance of classified group and non classified group, the prediction process runs the 20% test set through the Neighborhood Based Collaborative Filtering Algorithm and Correspondence Mean Algorithm. The prediction errors from those prediction algorithm are allocated to each customer and compared with each user's error. Research hypothesis : Two research hypotheses are formulated in this study to test the accuracy of the classification criterion as follows. Hypothesis 1: The estimation accuracy of groups classified according to the standard deviation of each user's ratings has significant difference. To test the Hypothesis 1, the standard deviation is calculated for each user in training set which is divided 80% from MovieLens 100K dataset. Four groups are classified according to the quartile of the each user's standard deviations. It is compared to test the estimation errors of each group which results from test set are significantly different. Hypothesis 2: The estimation accuracy of groups that are classified according to the distribution of each user's ratings have significant differences. To test the Hypothesis 2, the distributions of each user's ratings are compared with the distribution of ratings of all customers in training set which is divided 80% from MovieLens 100K dataset. It assumes that the customers whose ratings' distribution are different from that of all customers would have low performance, so six types of different distributions are set to be compared. The test groups are classified into fit group or non-fit group according to the each type of different distribution assumed. The degrees in accordance with each type of distribution and each customer's distributions are tested by the test of ${\chi}^2$ goodness-of-fit and classified two groups for testing the difference of the mean of errors. Also, the degree of goodness-of-fit with the distribution of each user's ratings and the average distribution of the ratings in the training set are closely related to the prediction errors from those prediction algorithms. Through this study, the customers who have lower performance of prediction than the rest in the system are classified by those two criteria, which are set by statistical features of customers ratings in the training set, before the prediction process.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.1
• /
• pp.73-76
• /
• 2009

Purpose: Bone mineral densitometry test region advised by ISCD (International Society for Clinical Densitometry) is both site in case of femur, whereas our medical center measures left femur except for few extraordinary cases. It is said that right-handers had higher mean femur BMD in the left side than in the right side, but the factor influence the femur BMD is unknown. Thus, we investigate whether testing left femur only is a adequate clinical diagnosis. Materials and Methods: Subjects were 209 right-handers and 20 left-handers patient in Asan Medical Center from July to August, 30 to 70 years of age ($51{\pm}6.7$). Subjects fill out the questionnaire on hand preference and taking regular exercise. Total BMDs of bilateral femur were measured with GE Lunar Prodigy advance densitometer, and the statistical soft ware SPSS 12.0 for windows was used for statistical analysis. Results: In the total sample of the exercise group (n=127), the difference of both femur mean BMDs are $0.001{\pm}0.127\;g/cm^2$ and the non-exercise group's (n=102) both femur difference is $0.002{\pm}0.126\;g/cm^2$, there is no significant difference. And in exercise group, classified according to hand preference, each t-value is shown at right handers (n=114) are 0.65, left handers (n=13) are -0.39. Also, In non-exercise group, right handers (n=95) are -0.78, left handers (n=7) are -0.64. In the 95% confidence limit, there was no statistically significant difference (p>0.05). Conclusions: In recently researchs, there have been differences between both femurs according to hand preference. However, Our study have no significant difference both femurs BMDs. Therefore we suggest that BMD measurement of femur has no problem only one side, except for particular case like femur operation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.1
• /
• pp.1-8
• /
• 2014

Purpose: The purpose of this study is to evaluate the effect of applying Silano-pen to feldspathic porcelain and zirconia on shear bond strength with composite resin. Materials and methods: Feldspathic porcelain and zirconia specimens were produced into 30 per each 2 mm thick and 12 mm in diameter and their surface was made smooth and even and then embedded in acrylic resin. The specimens were divided into each Group F (Feldspathic porcelain) and Group Z (Zirconia), (1) Hydrofluoric acid etching and silane (F1 & Z1), (2) Silano-pen and silane (F2 & Z2), (3) Hydrofluoric acid etching and Silano-pen, silane (F3 & Z3). After surface conditioning, substrate surfaces of the specimen were examined by SEM. Composite resin cylinders (2 mm high, 3 mm in diameter)were bonded to specimen and shear bond strength between ceramic and composite resin was measured by using universal testing machine. The measured values were statistically analyzed by using two way ANOVA and Tukey's multiple comparison test (${\alpha}=.05$). Results: In the scanning electron micrograph of the treated ceramic surface, Group F2 and F3 appeared the high roughness and Group Z3 appeared the highest density of silica particle. In Feldspathic porcelain, the result of measuring shear bond strength showed that Group F3 was measured to be highest and Group F1 was measured to be lowest but there was no statistical significance among Groups. In zirconia, Group Z3 was measured to be highest and Group Z1 was measured to be lowest and there was statistical significance among Groups (P<.05). Conclusion: In zirconia, applying hydrofluoric acid etching and then Silano-pen and silane is effective for composite resin adhesion.