• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.353-354
• /
• 2020

본 논문에서는 SiC (Silicone Carbide) MOSFET 기반 Buck-Unfolder 토폴로지를 적용한 단상 태양광 인버터를 개발한다. 개발한 인버터의 성능 평가를 위해 3.5kW 급 prototype의 효율 및 전고조파 왜율(THD)을 분석한다.

• Journal of the Korean Vacuum Society
• /
• v.2 no.2
• /
• pp.188-198
• /
• 1993

We have developed a technique for growing thin oxides (6~10 nm) by the Last step TCA method. N-channel metal-oxide-semiconductor (n-MOS) capacitor and n-channel metal-oxide-semiconductor field-effect transistor's (MOSFET's) having a gate oxide with chlorine incorporated $SiO_2/Si$ interface have been analyzed by electrical measurements and physical methods, such as secondary ion mass spectrometry (SIMS) and electron spectroscopy for chemical analysis (ESCA). The gate oxide grown with the Last strp TCA method has good characteristics as follows: the electron mobility of the MOSFET's with the Last step TCA method was increased by about 7% and the defect density at the $SiO_2/Si$ interface decreases slightly compared with that with No TCA method. In reliability estimation, the breakdown field was 18 MV/cm, 0.6 MV/cm higher than that of the gate oxide with No TCA method, and the lifetime estimated by TDDB measurement was longer than 20 years. The device lifetime estimated from hot-carrier reliability was proven to be enhanced. As the results, the gate oxide having a $SiO_2/Si$ interface incorporated with chlorine has good characteristics. Our new technique of Last step TCA method may be used to improve the endurance and retention of MOSFET's and to alleviate the degradation of thin oxides in short-channel MOS devices.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.8
• /
• pp.1-8
• /
• 2004

Experimental results are presented for gate oxide degradation, such as SILC and soft breakdown, and its effect on device parameters under negative and positive bias stress conditions using n-MOSFET's with 3 nm gate oxide. The degradation mechanisms are highly dependent on stress conditions. For negative gate voltage, both interface and oxide bulk traps are found to dominate the reliability of gate oxide. However, for positive gate voltage, the degradation becomes dominated mainly by interface trap. It was also found the trap generation in the gate oxide film is related to the breakage of Si-H bonds through the deuterium anneal and additional hydrogen anneal experiments. Statistical parameter variations as well as the “OFF” leakage current depend on both electron- and hole-trapping. Our results therefore show that Si or O bond breakage by tunneling electron and hole can be another origin of the investigated gate oxide degradation. This plausible physical explanation is based on both Anode-Hole Injection and Hydrogen-Released model.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.425-430
• /
• 2013

In this paper, we propose a triple-gate trench power MOSFET (TGRMOS) that is made through a modified RESURF stepped oxide (RSO) process, that is, the nitride_RSO process. The electrical characteristics of TGRMOSs, such as the blocking voltage ($BV_{DS}$) and on-state current ($I_{D,MAX}$), are strongly dependent on the gate configuration and its bias condition. In the nitride_RSO process, the thick single insulation layer ($SiO_2$) of a conventional RSO power MOSFET is changed to a multilayered insulator ($SiO_2/SiN_x/TEOS$). The inserted $SiN_x$ layer can create the selective etching of the TEOS layer between the gate oxide and poly-Si layers. After additional oxidation and the poly-Si filling processes, the gates are automatically separated into three parts. Moreover, to confirm the variation in the electrical properties of TGRMOSs, such as $BV_{DS}$ and $I_{D,MAX}$, simulation studies are performed on the function of the gate configurations and their bias conditions. $BV_{DS}$ and $I_{D,MAX}$ are controlled from 87 V to 152 V and from 0.14 mA to 0.24 mA at a 15-V gate voltage. This $I_{D,MAX}$ variation indicates the specific on-resistance modulation.

• Korean Journal of Materials Research
• /
• v.18 no.5
• /
• pp.272-276
• /
• 2008

In submicron MOSFET devices, maintaining the ratio between the channel length (L) and the channel depth (D) at 3 : 1 or larger is known to be critical in preventing deleterious short-channel effects. In this study, n-type SOI-MOSFETs with a channel length of $0.1\;{\mu}m$ and a Si film thickness (channel depth) of $0.033\;{\mu}m$ (L : D = 3 : 1) were virtually fabricated using a TSUPREM-4 process simulator. To form functioning transistors on the very thin Si film, a protective layer of $0.08\;{\mu}m$-thick surface oxide was deposited prior to the source/drain ion implantation so as to dampen the speed of the incoming As ions. The p-type boron doping concentration of the Si film, in which the device channel is formed, was used as the key variable in the process simulation. The finished devices were electrically tested with a Medici device simulator. The result showed that, for a given channel doping concentration of $1.9{\sim}2.5\;{\times}\;10^{18}\;cm^{-3}$, the threshold voltage was $0.5{\sim}0.7\;V$, and the subthreshold swing was $70{\sim}80\;mV/dec$. These value ranges are all fairly reasonable and should form a 'magic region' in which SOI-MOSFETs run optimally.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.559-563
• /
• 2002

A threshold voltage model of SiC N-channel MOSFETs for high-temperature and hard radiation environments has been developed and verified by comparing with experimental results. The proposed model includes the difference in the work functions, the surface potential, depletion charges and SiC/$SiO_2$acceptor-like interface state charges as a function of temperature. Simulations of the model shoved that interface slates were the most dominant factor for the threshold voltage decrease as the temperature increase. To verify the model, SiC N-chnnel MOSFETS were fabricated and threshold voltages as a function of temperature were measured and compared wish model simulations. From these comparisons, extracted density of interface slates was $4{\times}10^{12}\textrm{cm}^{-2}eV^{-1}$.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.205-208
• /
• 2020

This paper examines the approach, enabled by using SiC power devices, to unify the inverter design for central air conditioning (CAC) system for both single- and 3-phase input, and reduce the PFC inductor size to be PCB-mountable. By using SiC-instead of Si-diode in PFC stage, it is possible to increase the switching frequency from 16kHz to 60kHz to reduce the required PFC inductance from 0.93mH to 0.25mH, thus enable PCB-mounting of inductor. With the next step of using 1200V SiC MOSFET instead of Si-IGBT, the DC link voltage can be boosted from 311Vdc to 550Vdc in PFC stage, allowing the inverter and compressor used in 3-phase input CAC be used for single-phase input as well. Furthermore, using SiC MOSFET in inverter stage can further reduce total loss system total loss to 200.8 W. Simulation and experimental results are presented in the paper.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.43-51
• /
• 2023

In this paper, we introduce the development trends of power devices which is the key component for power conversion system in electric vehicles, and discuss the characteristics of the next-generation wide-bandgap (WBG) power devices. We provide an overview of the characteristics of the present mainstream Si insulated gate bipolar transistor (IGBT) devices and technology roadmap of Si IGBT by different manufacturers. Next, recent progress and advantages of SiC metal-oxide-semiconductor field-effect transistor (MOSFET) which are the most important unipolar devices, is described compared with conventional Si IGBT. Furthermore, due to the limitations of the current GaN power device technology, the issues encountered in applying the power conversion module for electric vehicles were described.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.10
• /
• pp.24-31
• /
• 2003

Short channel effects (SCE) of bulk MOSFET with super-steep retrograded channels (SSR), fully-depleted SOI, and double-gate MOSFET have been analyzed using a evanescent-mode analysis. Analytical equations of the characteristics scaling-length (λ) for three structures have been derived and the accuracy of the calculated λ was verified by comparing to the device simulation result. It is found that the minimum channel length should be larger than 5λ and the depletion thickness of the SSR should be around 30 nm in order to be applicable to 70 nm CMOS technology. High-$textsc{k}$ dielectric shows a limitation in scaling due to the drain-field penetration through the dielectric unless the equivalent SiO2 thickness is very thin.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1619-1626
• /
• 2017

Electronic components that are used in high-level radiation environment require a semiconductor device having a radiation-hardened characteristic. In this paper, we proposed a radiation-hardened I-gate n-MOSFET (n-type Metal Oxide Semiconductors Field Effect Transistors) using a layout modification technique only. The proposed I-gate n-MOSFET structure is modified as an I-shaped gate poly in order to mitigate a radiation-induced leakage current in the standard n-MOSFET structure. For verification of its radiation-hardened characteristic, the M&S (Modeling and Simulation) of the 3D (3-Dimension) structure is performed by TCAD (Technology Computer Aided Design) tool. In addition, we carried out an evaluation test using a $Co^{60}$ gamma-ray source of 10kGy(Si)/h. As a result, we have confirmed the radiation-hardened level up to a total ionizing dose of 20kGy(Si).