• 한국전기전자재료학회논문지
• /
• 제15권5호
• /
• pp.393-397
• /
• 2002

Polyimide (PI) films have been studied widely as the interlayer dielectric materials due to a low dielectric constant, low water absorption, high gap-fill and planarization capability. The polyimide film was etched using inductively coupled plasma system. The etcying characteristics such as etch rate and selectivity were evaluated at different $CF_4/(CF_4+O_2)$chemistry. The maximum etch rate was 8300 ${\AA}/min$ and the selectivity of polyimide to SiO$_2$was 5.9 at $CF_4/(CF_4+O_2)$ of 0.2. Etch profile of polyimide film with an aluminum pattern was measured by a scanning electron microscopy. The vertical profile was approximately $90^{\circ}$ at $CF_4/(CF_4+O_2)$ of 0.2. As 20% $CF_4$ were added into $O_2$ plasma from the results of the optical emission spectroscopy, the radical densities of fluorine and oxygen increased with increasing $CF_4$ concentration in $CF_4/O_2$ from 0 to 20%, resulting in the increased etch rate. The surface reaction of etched PI films was investigated using x-ray photoelectron spectroscopy.

• 한국전기전자재료학회논문지
• /
• 제21권9호
• /
• pp.848-852
• /
• 2008

Characteristics of microcrystalline-silicon thin-films deposited by plasma-enhanced chemical-vapor deposition (PECVD) method were studied. There were optimum values of RF power density and $H_2$ dilution ratio $(H_2/(SiH_4+H_2))$; maximum grain size of about 35 nm was obtained at substrate temperature of 250 $^{\circ}C$ with RF power density of 1.1 W/$cm^2$ and $H_2$ dilution ratio of 0.91. Larger grain was obtained with higher substrate temperature up to 350 $^{\circ}C$. Grain size dependence on RF power density and $H_2$ dilution ratio could be explained by etching effects of hydrogen ions and changes of species of reactive precursors on growing surface. Surface-mobility activation of reactive precursors by temperature could be a reason of grain-size dependence on the substrate temperature. Microcrystalline-silicon thin-films that could be used for flat-panel electronics such as active-matrix organic-light-emitting-diodes are expected to be fabricated successfully using these results.

• 한국전기전자재료학회논문지
• /
• 제24권9호
• /
• pp.687-692
• /
• 2011

Hafnium oxide ($HfO_2$) was very advantageous for substitute material of gate on existing transistor. $HfO_2$ has been widely studied due to high contact with polysilicon and thermal stability and also, it is easily etched by using HF solution. In this study, $HfO_2$ and thermal oxide films were etched by wet etch method using chemical etchant. Etch rate of $HfO_2$ and thermal oxide was linearly increased with increasing concentration of HF and temperature but etch rate of $HfO_2$ was higher than thermal oxide due to $H^+$, $F^-$, and $HF_2^-$ ions at below 0.5% concentration of HF. And also, etch selectivity was improved by adding Hydrazine as additive.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.127-128
• /
• 2007

고밀도 트렌치 게이트 전력소자 제조를 위해 HBr. He-$O_2$, $SiF_4$, $CF_4$ 등의 식각 가스를 이용하여 형성한, 트렌치 표면 거칠기 및 손상을 최소화 하여 고밀도 트렌치 게이트 전력소자를 제조하였다. 트렌치 형상 각도가 약 900일 경우 항복전압은 약 29 V인 반면, 트렌치 각도가 $88^{\circ}$일 경우 항복전압이 37V로 트렌치 형상에 따라 약 25%의 항복전압이 높아졌음을 알 수 있었다. n-채널 트렌치 게이트 전력소자의 전압-전류 측정 결과 트렌치 게이트 수가 45.000개일 때 게이트에 10 V를 인가했을 때 전류는 약 46 A로 측정되어 고밀도 트렌치 게이트 전력소자의 특성이 좋음을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.40-41
• /
• 2007

$SnO_2$ nanowires are used at the nanoscale level for the electrical transduction of the gas interaction with these sensing materials. We report on a study of high sensitivity and fast NOx gas sensor. We focused on improving the response time and refresh time by growth nanowires on the trench structure of Si substrate as air path. To improve refresh time we applied the trench structure with depth of $10\;{\mu}m$ by the inductively coupled plasma reactive ion etching(ICP-RIE). The fabricated device was measured at temperature of $200{\sim}300^{\circ}C$. The sensor exhibit ultra-fast and reversible electrical response (t90% ~4 s for response and ~3 s for recovery).

• 한국전기전자재료학회논문지
• /
• 제27권12호
• /
• pp.871-876
• /
• 2014

Efficiency of crystalline Si solar cell can be maximized as minimizing optical loss through antireflection texturing with inverted pyramids. Even if cost-competitive, soft lithography can be employed instead of photolithography for the purpose, some limitations still remain to apply the soft lithography directly to as-received solar grade wafer with a bunch of micro trenches on surface. Therefore, it is needed to develop a low-cost, effective planarization process and evaluate its output to be applicable to patterning process with PDMS stamp. In this study new surface planarization process is proposed and the change of micro scale trenches on the surface as a function of etching time is observed. Also, the effect of trenches on pattern quality by soft lithography is investigated using FEM structural analysis. In conclusion it is clear that the geometry and shape of trenches would be basic considerations for soft lithography application to low quality wafer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.17-18
• /
• 2007

The etching characteristics of Zinc Oxide (ZnO) and etch selectivity of ZnO to $SiO_2\;in\;BCl_3$/Ar plasma were investigated. It was found that ZnO etch rate shows a non-monotonic behavior with increasing both Ar fraction in $BCl_3$ plasma, RF power, and gas pressure. The maximum ZnO etch rate of 50.3 nm/min was obtained for $BCl_3$ (80%)/Ar(20%) gas mixture. The plasmas were characterized using optical emission spectroscopy (OES) analysis measurements while chemical state of etched surfaces was investigated with X-ray photoelectron spectroscopy (XPS). From these data the suggestions on the ZnO etch mechanism were made.

• 한국표면공학회지
• /
• 제45권4호
• /
• pp.151-154
• /
• 2012

A hydrophobic surface has been fabricated on aluminum by two-step surface treatment processes consisting of structure modification and surface coating. Nature inspired micro nano scale structures were artificially created on the aluminum surface by a blasting and Ar ion beam etching. And a hydrophobic thin film was coated by a trimethylsilane ($(CH_3)_3SiH$) plasma deposition to minimize the surface energy of the micro nano structure surface. The contact angle of micro nano structured aluminum surface with the trimethylsilane coating was $123^{\circ}$ (surface energy: 9.05 $mJ/m^2$), but the contact angle of only trimethylsilane coated sample without the micro nano surface structure was $92^{\circ}$ (surface energy: 99.15 $mJ/m^2$). In the hydrophobic treatment of aluminum surface, a trimethylsilane coated sample having the micro nano structure was more effective than only trimethylsilane coated sample without the micro nano structure.

• 대한금속재료학회지
• /
• 제49권5호
• /
• pp.400-405
• /
• 2011

ZnO nanotube arrays were synthesized by a two-step process: electrodeposition and selective dissolution. In the first step, ZnO nanorod arrays were grown on an Au/Si substrate by using a homemade electrodeposition system. ZnO nanorod arrays were then selectively dissolved in an etching solution composed of 0.125 M NaOH, resulting in hollow ZnO nanotube arrays. It is suggested that the formation mechanism of the ZnO nanotube arrays might be attributed to the preferred surface adsorption of hydroxide ion ($OH^{-1}$) on a positive polar surface followed by selective dissolution of the metastable Zn-terminated ZnO (0001) polar surface caused by the difference in the surface energy per unit area between the ZnO nanorod and nanotube.

• 한국표면공학회지
• /
• 제55권5호
• /
• pp.247-260
• /
• 2022

Since the first report on ferroelectricity in Si-doped hafnia (HfO2), this emerging ferroelectrics have been considered promising for the next-generation semiconductor devices with their characteristic nonvolatile data storage. The robust ferroelectricity in the sub-10-nm thickness regime has been proven by numerous research groups. However, extending their scalability below the 5 nm thickness with low temperature processes compatible with the back-end-of-line technology. In this review, therefore, the current status, technical issues, and their potential solutions of atomic layer deposition (ALD) of HfO₂-based ferroelectrics are comprehensively reviewed. Several technical issues in the physical scaling of the ferroelectric thin films and potential solutions including advanced ALD techniques including discrete feeding ALD, atomic layer etching, and area selective ALD are introduced.