• Journal of Biosystems Engineering
• /
• v.42 no.4
• /
• pp.242-250
• /
• 2017

Purpose: This study was conducted to determine the appropriate operating conditions through a factorial experiment for the secondary separating part of the self-propelled pepper harvester. Methods: An experimental setup that simulates the secondary separating part of the self-propelled pepper harvester was organized. Test samples were classified into three types according to the number of peppers on a stem, and 12 sets were prepared for each type. Among the operating conditions of the secondary separating part, the rotational speed of drum B (four levels), radial clearance between drums and cylindrical teeth (three levels), and speed ratio between the three drums (two levels) were set as the test factors, and tests were repeated three times for different levels of each factor. The appropriate operating conditions were determined by analyzing the separation ratio and damage ratio of the peppers collected through the secondary separating part. Results: The test factors changed the overall separation ratio and overall damage ratio in similar trends. In other words, the conditions that caused high overall separation ratios also exhibited high overall damage ratios. Owing to the high overall damage ratio in the condition with the highest overall separation ratio, the operating conditions should be selected considering both ratios. Conclusions: When the condition with more than 60% of overall separation ratio and less than 15% of overall damage ratio was considered as the appropriate operating condition, 70 rpm of the rotational speed of drum B, 5 mm of the radial clearance between drums and cylindrical teeth, and 7:3:5 for the speed ratio of the three drums A, B, and C should be applied for the secondary separating part used in this study. Supplementary studies will be required in the future to find optimal operating conditions through the actual field test under further divided test factors.

• Journal of Biosystems Engineering
• /
• v.29 no.5 s.106
• /
• pp.433-440
• /
• 2004

Worldwide consumption of vegetable soybean has been increasing recently, but in the process of vegetable soybean production, threshing and separation work accounts fur about $80\%$ of overall labor. Therefore, developing of the vegetable soybean thresher is necessary to reduce the cost of labor. The main objective of this study is to acquire the basic in-formations for design of the vegetable soybean thresher which is suitable for domestic circumstances. We made the experimental system to investigate the threshing and separating performance at the several speeds of threshing cylinder and separating blower according to the kinds of threshing tooth. The result are as follows; Threshing performance of vegetable soybean thresher was shown as the best in case the threshing tooth made of rubber which has the 80 of Shore hardness was used at the circumference speed of cylinder of 5.8$\~$8.1m/s. Also separating cleaning performance of vegetable soybean thresher was shown as the best at more than 1,300 rpm of blower speed and $60\~80\%$ of opening ratio of suction port.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.2
• /
• pp.139-143
• /
• 1998

In the fishing process on the sea eel pots, the most dangerous and difficult labor is manually separating process of several thousand pots from main line with high speed hauling operation. In this study, the automatic separating system of the pot from main line is developed. This system is composed with the clip connected to the pot by branch line, the keeper attached to the main line by pressing and the separator separating the clip and the keeper. In the experiment, static and dynamic characteristics of the system are investigated. From the considerations on the experimental results, it is ascertained that the automatic separating system of the pot from main line proposed in this study has good operating performance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.515-518
• /
• 1997

Resident time of the centrifugal extractor for organic phase extraction using a height controlled separator weir and a divert plate is the important factor that affects significantly the chemical material extraction and the productivity in the chemical and mechanical processes. In this paper, it describes the design of the device for extraction of an organic phase from radioactive wastes, and considers phase separating weir and divert disk, both being designed to be adjustable in their positions, for effectively separating an organic phase. A height-adjustable separating weir unit used for separating the organic phase from the aqueous phase using a phase separating weir and designed to control the height of the separating weir as desired so as to allow the weir to be positioned at a boundary layer between two separated phases. The centrifugal extractor controls satisfactorily the mixed reaction time of two phases within the separator regardless of the variations of the mixing ratio of the two phases and the rotating speed of the extractor, is designed to be adjustable in its position in the vertical direction, thus allowing the user to appropriately select the mixed reaction time of the two phases within the extractor as desired. From development of a centrifugal extractor, it can effectively recover such usable elements, and preferably reducing the output quantity of radioactive wastes.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.1
• /
• pp.3655-3665
• /
• 1975

This study was intended to develop a method for measuring the grain separating performance of threshers. The grain separating apparatus used for the experiment was designed and constructed, the function of which was to separate pneumatically mature and immature grain, chaff, straw, dust, and other impurities from the products of threshing. The apparatus has five material outlets where grains and impurities are fallen down by separation depending upon the specific gravity of the material white it moves above the outlets. The principle of design was to separate the mixture of mature grain, immature grain and chaff as distinct as possible, and to induce the mature grains onto the first outlet, the immature grains onto the second and the third, and the straw wastes onto the forth and the fifth outlets. The developed apparatus was tested to evaluate its separating performance with two rice varieties (Tongil and Mine-hikari) at different moisture levels and air velocities. The optimum conditions for operating the apparatus were found from experiment. The results are summarized as follows; 1. The degrees of separation, especially the amount of immature grain contained in the mature paddy, were dependent upon air speed delivered. The optimum air velocities for this apparatus for each levels of grain moisture contents were found from a series of experiments as follows; 14.7-15.3m/sec. for grain of 16 percent moisture content in wet basis, 15.3-16.0m/sec. for 20 percent, and 16.0-16.4m/sec for 24 percent. 2. Composition ratios determined based on the brine separating method was fairly well acted upon the developed apparatus, indicating its recollecting rate of the mature grains as 97.6 to 99.9 percent. The developed separatus acted similarly upon the two rice varieties which had different composition of immature paddy grain. In other words, the separating performance by the apparatus had a good correlation with the one by the brine separating method. 3. As immature grains were separated out unsatisfactory in these experiments than the brine separating method, further investigation may be needed to improve a separating performance of these materials. But the results obtained suggested a possibility of using the tester to replace the current hand separating method, ther eby enabling more consistent test results and also eliminating nearly all costly hand seperating operations.

• Journal of Biosystems Engineering
• /
• v.13 no.3
• /
• pp.32-43
• /
• 1988

This study was attempted to investigate the pneumatic separation on separating unit of a combine harvester. The aerodynamic characteristics of threshed materials were analyzed by experiments. The air velocity distribution within the separation chamber was measured for various speeds of the winnower and suction fans to find out the operational and design conditions of the separating unit which would serve for reducing the grain loss from chaff outlet. The results of study arc summarized as follows: 1. Based on the separation curve of threshed materials analyzed, it was shown that three different kind. of materials-kernels, straw chaff, and leaf chaff were as a whole able to be separated pneumatically, regardless of varieties. However, a small amount of the separation grain loss may be expected to occur if the complete separation between kernels and straw chaff would be undertaken because some portion of their separation curve were overlapping. 2. The analysis of air velocity distribution showed that the separation chamber may be divided into two regions, the discharging and separating. The air velocity of the discharging region was 5-15 m/s and that of the separating region 2-5 m/s. 3. The air movement of the separation chamber may be a turbulence flow, being its speed became greater as it moves from the left to the right section of the separation chamber. The equi-speed line. of air flow had a steep gradient in between the discharging and the separation regions. The air velocity in the discharging region was much higher than the terminal velocity of kernels, because of which those kernels appearing in the region could be possibly exhausted as the grain loss from the chaff outlet. 4. The motion trajectory of threshed material in the separating region was dominantly affected by the winnower fan, on the other hand, its motion in the discharging region was affected by suction fan. 5. The grain loss from the chaff outlet was affected greatly by the winnower fan and the trace of kernel movement. It was observed that the optimum working speed to give minimum grain loss from chaff outlet for the combine tested should be maintained at 950~1,150 rpm for the winnower fan and 1,850 rpm for the suction fan. 6. It was shown that a large portion of grain loss from chaff outlet may occur when the kernels may bump against a portion of separation chamber wall and those kernels thus scattered into the discharging region were sucked by the suction fan. It was accordingly recommended that a new design of the wall of separation chamber so as to bump down kernels may be necessary to reduce grain loss from the chaff outlet.

• Journal of Biosystems Engineering
• /
• v.26 no.2
• /
• pp.131-140
• /
• 2001

This study was conducted to develop a garlic separator which could to reduce the labor in preparation of seeding. After consideration of the design criteria of a garlic separator such as no additional conveying device, simple construction and operation, enhancement of separating efficiency, reduction of damage, degree a rotating corn type garlic separator was designed. The effects of design parameters such as height and angle of the inner and outer corns, rotating speed of inner corn on the separating performance of the prototype were estimated. In performance was compared with manual work. The results are summarized as follows. 1. Garlic bulbs were separated by a spiral movement in the gap between inner rotating corn and outer fixed corn. At constant feed rate of garlic bulbs, the capacity of garlic separation increased with increase of rotating speed of inner corn. Especially, the capacity was very high at the rotating speeds of 300 and 400rpm. 2. The damage degree of separated garlics increased with rotating speed of corn within 10%. Above 300rpm, separability of Uisung garlic was about 100% and incomplete separation of Namdo garlic was within 2%. 3. The capacity of prototype garlic separator developed in this study was 30 times as large as that of human being.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.1
• /
• pp.41-46
• /
• 2004

This paper proposes a separation of mixed signals by using the robust independent component analysis(RICA) based on neural networks. RICA is based on the temporal correlations and the second order statistics of signal. This method e is applied for improving the analysis rate and speed in which the sources have very small or zero kurtosis. The proposed method has been applied for separating the 10 mixed finger prints of $256{\times}256$-pixel and the 4 mixed images of $512{\times}512$-pixel, respectively. The simulation results show that RICA has the separating rate and speed better than those using the conventional FP algorithm based on Newton method.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.48-59
• /
• 1981

The major limiting factor on the determination of combine capacity is the frequent occurence of clogging over the some parts of machine when the crop is wet in the case of Japanese self-feeding type combine. And in the case of American conventional combine having big separating parts, the great grain loss and damage occur when the machine is used for rice harvesting. This experiment was carried out to develop the new type threshing and separating equipment. Proto-type thresher which consist of a conical threshing drum and a conical separating sieve rotating around the threshing cone was constructed and tested. In the case of 800 rpm of threshing cone speed, average threshing loss was below 1 percent, separating loss was about 1 percent, grain damage was about 0.4 percent, and average total power required was about 2.6 PS. This design has some problems such as higher power required or wrapping problems under the conditions of feeding long damp straw. But, compared with the conventional combine or thresher, this machine certainly has some potentials for this approach to combine development. The crop feed rate must be increased through improvement of the feeding portion of the threshing cone. And it is required to investigate further about some parameters causing wrapping phenomena.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.11
• /
• pp.922-931
• /
• 2017

This research paper describes design procedures and those verification with multi-body dynamic analysis and an experiment for the development of an unprecedented type of canister cover, named as the separating cover. In order to overcome drawbacks from the precious rupture type and actuator driven cover, the separating cover was suggested. It has the simplest structure composed of the previously developed explosive bolt and a spring-lever driven system. First of all, mechanical feasibility with proposed design parameters based on mathematical modeling was confirmed through dynamic analysis and then its results showed good agreement with the followed empirical results acquired from a high speed camera. On top of that, a parametric study was conducted to identify the effect of each design parameter on separating performance. It is highly expected that this research contributes to provide military industries with a brand new canister cover having simplicity and cost efficiency and thus it will be very useful in MLRS(Multiple Launch Rocket System).