• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.7
• /
• pp.807-815
• /
• 2019

In this paper, we design a power amplifier to support quad-band in wireless communication devices using RF CMOS 180-nm process. The proposed power amplifier consists of low-band 0.9, 1.8, and 2.4 GHz and high-band 5 GHz. We proposed a structure that can support each input matching network without using a switch. For maximum linear output power, the output matching network was designed for impedance conversion to the power matching point. The fabricated quad-band power amplifier was verified using modulation signals. The long-term evolution(LTE) 10 MHz modulated signal was used for 0.9 and 1.8 GHz, and the measured output power is 23.55 and 24.23 dBm, respectively. The LTE 20 MHz modulated signal was used for 1.8 GHz, and the measured output power is 22.24 dBm. The wireless local area network(WLAN) 802.11n modulated signal was used for 2.4 GHz and 5.0 GHz. We obtain maximum linear output power of 20.58 dBm at 2.4 GHz and 17.7 dBm at 5.0 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.1
• /
• pp.91-99
• /
• 2018

This paper has proposed a low-noise and high-linear RF receiver supporting TV white space from 470 MHz to 698 MHz), which is implemented in $0.13-{\mu}m$ CMOS technology. It consists of a low-noise amplifier, a RF band-pass filter, a RF amplifier, a passive down-conversion mixer, and a channel-selection low-pass filter. A low-noise amplifier and RF amplifier provide a high voltage gain to improve the sensitivity level. To suppress strong and nearby interferers, two RF filtering schemes have been performed by using a RF BPF and a down-conversion mixer. The proposed LPF has been based on the common-gate topology and adopted a bi-quad cell to achieve -24dB/oct characteristics. In addition, the RF receiver can support the overall TV band by controlling a LO frequency. The simulated results show a voltage gain of 56 dB, a noise figure of less than 2 dB, and an out-of-channel IIP3 of -2.3 dBm. It consumes 37 mA from a 1.5 V supply voltage.

• Journal of Advanced Navigation Technology
• /
• v.13 no.1
• /
• pp.48-53
• /
• 2009

The CMOS RF front-end for Global Positioning System(GPS)are implemented in 1P8M CMOS $0.13{\mu}m$ process. The LNAs consist of LNA1 with high gain and low NF, and LNA2 with low gain and high IIP3 for supporting operation with active and passive antenna. the measured performances of both LNAs are 16.4/13.8 dB gain, 1.4/1.68 dB NF, and -8/-4.4 dBm IIP3 with 3.2/2 mA form 1.2 V supply, respectively. The quadrature downconversion mixer is followed by transimpedance amplifier with gain controllability from 27.5 to 41 dB. The front-end performances in LNA1 mode are 39.8 dB conversion gain, 2.2 dB NF, and -33.4 dBm IIP3 with 6.6 mW power consumption.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.5
• /
• pp.100-105
• /
• 2010

A multi-band low noise amplifier (LNA) is designed in 90 nm RF CMOS process for 3GPP LTE (3rd Generation Partner Project Long Term Evolution) applications. The designed multi-band LNA covers the eight frequency bands between 1.85 and 2.8 GHz. A tunable input matching circuit is realized by adopting a switched capacitor array at the LNA input stage for providing optimum performances across the wide operating band. Current steering technique is adopted for the gain control in three steps. The performances of the LNA are verified through post-layout simulations (PLS). The LNA consumes 17 mA at 1.2 V supply voltage. It shows a power gain of 26 at the normal gain mode, and provides much lower gains of 0 and -6.7 in the bypass-I and -II modes, respectively. It achieves a noise figure of 1.78 dB and a IIP3 of -12.8 dBm over the entire band.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.109-114
• /
• 2023

In this paper, a 2-channel Image-Reject receiver using a 65-nm CMOS process is presented for Ka-band compact radars. The designed receiver consists of Low-Noise Amplifier (LNA), IQ mixer, and Analog Baseband (ABB). ABB includes a complex filter in order to suppress unwanted images, and the variable gain amplifiers (VGAs) in RF block and ABB have gain tuning range from 4.5-56 dB for wide dynamic range. The gain of the receiver is controlled by on-chip SPI controllers. The receiver has noise figure of <15 dB, OP1dB of >4 dBm, image rejection ratio of >30 dB, and channel isolation of >45 dB at the voltage gain of 36 dB, in the Ka-band target frequency. The receiver consumes 420 mA at 1.2 V supply with die area of 4000×1600 ㎛.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.112-116
• /
• 2005

This paper presents a broadband two-stage low noise amplifier(LNA) operating from 3 to 10 GHz, designed with 0.18 ${\mu}m$ RF CMOS technology, The cascode feedback topology and broadband matching technique are used to achieve broadband performance and input/output matching characteristics. The proposed UWB LNA results in the low noise figure(NF) of 3.4 dB, input/output return loss($S_{11}/S_{22}$) of lower than -10 dB, and power gain of 14.5 dB with gain flatness of $\pm$1 -dB within the required bandwidth. The input-referred third-order intercept point($IIP_3$) and the input-referred 1-dB compression point($P_{ldB}$) are -7 dBm and -17 dBm, respectively.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.35-38
• /
• 2010

A fully integrated parallel-coupled 6-GHz quadrature voltage-controlled oscillator (QVCO) has been designed. The symmetrical parallel-coupled quadrature VCO is implemented using 0.13-${\mu}m$ CMOS process. The measured phase noise is -101.05 dBc/Hz at an offset frequency of 1 MHz. The tuning range of 710 MHz is achieved with a control voltage ranging from 0.3 to 1.4 V. The average output phase error is about $1.26^{\circ}$ including cables and connectors. The QVCO dissipates 10 mA including buffer from the 1.5 V supply voltage. The output characteristic of the differential injection-locked frequency divider (DILFD), which has similar topology to the QVCO, is presented.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.3
• /
• pp.190-197
• /
• 2011

This paper presents a 144 GHz divide-by-2 injection locked frequency divider (ILFD) with inductive feedback developed in a commercial 90-nm Si RFCMOS technology. It was demonstrated that division-by-2 operation is achieved with input power down to -12 dBm, with measured locking range of 0.96 GHz (144.18 - 145.14 GHz) at input power of -3 dBm. To the authors' best knowledge, this is the highest operation frequency for ILFD based on a 90-nm CMOS technology. From supply voltage of 1.8 V, the circuit draws 5.7 mA including both core and buffer. The fabricated chip occupies 0.54 mm ${\times}$ 0.69 mm including the DC and RF pads.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.91-95
• /
• 2008

This paper presents a direct-conversion I/Q up-mixer block, which supports $3{\sim}5$ GHz ultra-wideband(UWB) applications. It consists of a VI converter, a double-balanced mixer, a RF amplifier, and a differential-to-single signal converter. To achieve wideband characteristics over $3{\sim}5$ GHz frequency range, the double-balanced mixer adopts a shunt-peaking load. The proposed RF amplifier can suppress unwanted common-mode input signals with high linearity. The proposed direct-conversion I/Q up-mixer block is implemented using $0.18-{\mu}m$ CMOS technology. The measured results for three channels show a power gain of $-2{\sim}-9$ dB with a gain flatness of 1dB, a maximum output power level of $-7{\sim}-14.5$ dBm, and a output return loss of more than - 8.8 dB. The current consumption of the fabricated chip is 25.2 mA from a 1.8 V power supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.10B
• /
• pp.1353-1359
• /
• 2001

본 논문에서는 위상획득과정과 동기과정에서 trade-off 현상을 향상시킨 듀얼 위상 주파수 검출기를 제안하여 차지펌프 PLL을 설계하였다. 듀얼 위상 주파수 검출기는 상승에지에서 동작하는 POSITIVE 위상 주파수 검출기와 하강에지에서 동작하는 NEGATIVE 위상 주파수 검출기로 구성되어 있다. 제안한 차지펌프는 전류뺄셈회로를 이용하여 전류 부정합을 감소시켰으며, reference spurs와 전압제어발진기의 변동을 감소시킬 수 있도록 구현하였다. 제안한 차지펌프 PLL은 0.25$\mu\textrm{m}$ CMOS 공정을 사용하여 SPICE로 시뮬레이션 하였으며, 그 결과 1.6~1.85GHz의 넓은 동기범위를 나타내었다.