• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.637-638
• /
• 2006

V-belt pulleys play a key role in driving cooling pump, oil pump, air-conditioner and so on by using an engine power. Precision deep drawing is one of the main processes for manufacturing the pulleys. Operation variables of the deep drawing equipment, called the setup parameter, must be re-determined whenever the specifications of pulley to be produced are changed. The defect rates during a setup of equipment and the working hours needed for the setup are almost dependent on workers' know-how. This study designs the program for easily determining setup conditions in pulley manufacturing process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.209-218
• /
• 2002

A V belt pulley is widely used in automotive industry. More than tow pulleys in one automobile are used, such items as crankshaft, water pump, air-con compressor and power steering pump. Although the shape and usage of pulleys are very simple, the design evaluation of a pulley design is difficult because the load conditions and the installation environment are complicated. So, we formulated the design evaluation for the V belt pulley by using CAE system, which enables to develop a design automation system. By using this system, an engineer can evaluate a pulley design easily without any painstaking effort, such as consideration of the complicated loads and CAE activities. Also the system helps to accumulate the design experience of a company, which guides the optimum design based on experience.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.3
• /
• pp.26-32
• /
• 2015

The authors are developing a motion of floater body type wave energy converter of the float-counterweight system. This consists of the driving pulley, wire, float and counterweight suspended from idler pulleys and rachet mechanism. Though it has succeeded in solving the major structural strength problem in which the floats would slam against adjacent structure(s) by wave load acting horizontally. In order to overcome this problem. We propose a new system in which the wire transmitting the power is wound around the pulleys and the float receiving the wave power is pulled by the wire from both its upper and lower ends to avoid the occurrence of slackening during the wave cycle. In the paper, we developed the dynamics model for the proposed system. Energy gain has been calculated for realistic wave conditions and compared with the original float-counterweight device. The important differences from the float-counterweight system are that (1) both upward and downward motions of water surface can be utilized without problem. (2) slackening of energy gain and wire tension are effectively suppressed, and (4) for the same time averaged energy gain, the maximum wire tension is fairly lowered.

• Journal of Wind Energy
• /
• v.15 no.1
• /
• pp.91-102
• /
• 2024

Rapid progress is being made in foundational technology research and engineering for the construction of floating offshore wind farms. There is active development of technology for detachable mooring systems, which have strengths in addressing maintenance issues that arise in floating offshore wind farms and enhance their economic viability. Conventional detachable mooring systems use Kenter links inserted into the middle of mooring chains, which require excessive time for retrieval by Anchor Handling Tug Supply (AHTS) vessels during detachment operations. Moreover, these operations pose risks of link damage and accidents. Therefore, there is a demand for the development of a new concept of detachable mooring systems. The proposed detachable mooring system in this study simultaneously integrates a fairlead chain stoppers (FCS) and submersible mooring pulleys (SMP), which enables all operations to be conducted on the AHTS vessel without underwater tasks. This study detailed the design and safety evaluation of the SMP, a core component of the detachable mooring system, based on the minimum breaking load (MBL) of selected mooring lines according to the capacity of the floating platform. It referenced international codes (AISC Specification for Structural Steel Buildings D5, Pin-Connected Members) for design verification and performed finite element analysis to evaluate the strength of major components in installation and operation scenarios. Additionally, procedures and techniques for evaluating the structural strength of components under uncertain boundary conditions were proposed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.255-264
• /
• 2002

In this paper, the power transmitting mechanism for negative torque of the metal V-belt (MVB) CVT were investigated by theoretically analyzing variation of band tension, block compression forces for each of the primary and secondary pulleys. An experimental study was performed to investigate the speed ratio - thrust characteristics for negative torque. The experimental results are in good acoordance with the theoretical results. CVT line pressure control logic was suggested for negative torque based the speed radio - negative torque - thrust characteristics and the thrust ratio curves. The results of this study can be used as basic design materials for developing the CVT control system for negative torque.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.68-79
• /
• 1989

Dynamic characteristics for an automotive V-belt CVT with centrifugal and torque-ramp actuators was investigated by bondgraph modeling method. Ten(10) state space equations for the V-belt CVT were developed from the constructed bondgraph model and linearized for perturbation at steady state. As simulation results, speed ratio versus time curves were obtained. It was found that as the ratio of the moment of inertia of the pulleys increased, the stability of the V-belt CVT system decreased. Change in the ratio of the spring constants caused the magnitude of the change of the speed ratio, but had little effect on the settling time of the system became faster and the stability of the system improved. However, the sensitivity of the speed ratio decreased with the increasing .betha.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.11
• /
• pp.845-851
• /
• 2003

The nonlinear vibration of moving viscoelastic belts excited by the eccentricity of pulleys is investigated through experimental and analytical methods. Laboratory measurements demonstrate the nonlinearities in the responses of the belt particularly in the resonance region and with the variation of tension, The measurements of the belt motion are made using noncontact laser sensors. Jump and hysteresis phenomenon are observed experimentally and were studied with a model. which considers the nonlinear relation of belt stretch. An ordinary differential equation is derived as a working form of the belt equation of motion, Numerical results show good agreements with the experimental observations, which demonstrates the nonlinearity of viscoelastic moving belts.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.6
• /
• pp.119-126
• /
• 2000

In this paper. a simple high-speed crash test rig for members of vehicle was developed for the improvement of crashworthiness of vehicle's side rail. The cart hanging the specimen is accelerated up to 35 mph by the force of freely dropping weight and 1:3 accelerating pulleys. The cart with shock absorbers travels on the rail roads, so it does not transfer any additional vibration to the specimen. To measure the test results, two types of accelerator are considered. the one is a strain gage type and the other is a piezo type. The test rig is rated good to test the specimen like a side rail of vehicle as developing the vehicle's structures in the early design stage.

• Design & Manufacturing
• /
• v.7 no.1
• /
• pp.23-27
• /
• 2013

Orchard sprayers, wide area dusters and multipurpose control cars are flagship products of Hansung T&I Ltd. Spray pumps are one of the essential parts for these products. But conventional belt pulleys for spray pumps are heavy and expensive, and they bring down the quality as well as productivity of the end-products. Therefore, this study focuses on mold design for aluminum die casting belt pulley and mold manufacture.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.24 no.3
• /
• pp.149-156
• /
• 2020

The vibration control device such as the damper can be used to reinforce the seismic performance of structures. The damper is activated by the deformation of structures during earthquake; however, the deformation of structures is extremely small, causing difficulty in using the damper. Therefore, there is a need for a method capable of amplifying small deformities and transmitting them to the damper. The purpose of this paper is to develop and evaluate a displacement amplification seismic system using cable-pulley. The appropriate cable was selected through a cable tensile performance test and the results of the frame experiment were compared with theoretical displacement amplification ratio values. As a result, it may be said that the proposed system using cable-pulley is useful for displacement amplification.