• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.75-79
• /
• 2013

A power distribution network (PDN) is a network that provides connection between the voltage source supply and the power/ground terminals of a microprocessor chip. It consists of a voltage regulator module, a printed circuit board, a package substrate, a microprocessor chip as well as decoupling capacitors. For power integrity analysis, the board and package layouts have to be transformed into an electrical network of resistor, inductor and capacitor components which may be expressed using the S-parameters models. This modeling process generally takes from several hours up to a few days for a complete board or package layout. When the board and package layouts change, they need to be re-extracted and the S-parameters models also need to be re-generated for power integrity assessment. This not only consumes a lot of resources such as time and manpower, the task of PDN modeling is also tedious and mundane. In this paper, a block-based PDN modeling is proposed. Here, the board or package layout is partitioned into sub-blocks and each of them is modeled independently. In the event of a change in power rails routing, only the affected sub-blocks will be reextracted and re-modeled. Simulation results show that the proposed block-based PDN modeling not only can save at least 75% of processing time but it can, at the same time, keep the modeling accuracy on par with the traditional PDN modeling methodology.

• Current Photovoltaic Research
• /
• v.7 no.3
• /
• pp.71-75
• /
• 2019

Solar energy is one of the renewable energy sources. It can respond to expanding energy demand. A solar cell module is designed to have a durability that can be developed over a long period of 25 years to be installed outdoors and perform like a stable power supply. We need Standard Test Condition (STC)-based power output data before and after testing to measure the power output of existing modules. The modules are shown to reduce power output by comparing data before and after outdoor experiments regardless of whether they are indoor or outdoor. It is easy to compare the power output quantities through the module simulator in the indoor. However, it takes a lot of testing time and costs to compare the power output on outdoor in the case of a high number of modules and distance from the module simulator. It can save time and costs if we can check the power output using the data in outdoor. We have used the long-term outdoor test to find the elements out that corresponds to the reductions in power output quantities. We have conducted research that matched the actual and the tests.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.3
• /
• pp.1123-1140
• /
• 2019

Many Internet of Things (IoT) applications involving bursty traffic have emerged recently with event detection. A power management scheme qualified for uplink bursty traffic (PM-UBT) is proposed by distinguishing between bursty and general uplink traffic patterns in the IEEE 802.11 standard to balance energy consumption and uplink latency, especially for stations with limited power and constrained buffer size. The proposed PM-UBT allows a station to transmit an uplink bursty frame immediately regardless of the state. Only when the sleep timer expires can the station send uplink general traffic and receive all downlink frames from the access point. The optimization problem (OP) for PM-UBT is power consumption minimization under a constrained buffer size at the station. This OP can be solved effectively by the bisection method, which demonstrates a performance similar to that of exhaustive search but with less computational complexity. Simulation results show that when the frame arrival rate in a station is between 5 and 100 frame/second, PM-UBT can save approximately 5 mW to 30 mW of power compared with an existing power management scheme. Therefore, the proposed power management strategy can be used efficiently for delay-intolerant uplink traffic in event-driven IoT applications, such as health status monitoring and environmental surveillance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.821-827
• /
• 2001

A new low power charge-recycling ROM architecture is proposed. The charge-recycling ROM uses charge-recycling method in bit lines of ROM to save the power consumption. About 90% of the total power used in the ROM is consumed in bit lines. With the proposed method, power consumption in ROM bit lines can be reduced asymptotically to zero if the number of bit lines is infinite and the sense amplifiers detect infinitely small voltage difference. However, the real sense amplifiers cannot sense very small voltage difference. Therefore, reduction of power consumption is limited. The simulation results show that the charge-recycling ROM only consumes 13% ~ 78% of the conventional low power contact programming mask ROM.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.67-72
• /
• 2014

Inflow or outflow from the water treatment plant and the sewage water has potential energy. If this potential energy can be converted into electrical energy by water turbine generator, it can help to save energy because of the high capacity utilization. So recently, micro hydro power plant is reviewed in the water treatment facility. If generation capacity is low, induction generator is primarily used. If output capacity is low, generated power is supplied to the inside load. Induction generator can cause voltage drop by the inrush current at a start-up and requires reactive power for magnetization. In this study, we analyzed the flow of power and voltage variation against inrush current that occurs when the induction generator starts under the terms that loads of linear and non-linear of the water purification plant are used. Analysis results are that the voltage drop is within an allowable range and the power factor is slightly reduced by the need of reactive power.

• Journal of Communications and Networks
• /
• v.17 no.4
• /
• pp.394-405
• /
• 2015

This paper considers a wideband cognitive radio network which can simultaneously sense multiple narrowband channels and thus aggregate the detected available channels for transmission and proposes a novel cognitive radio system that exhibits improved sensing throughput and can save power consumption of secondary user (SU) compared to the conventional cognitive radio system studied so far. More specifically, under the proposed cognitive radio system, we study the problem of designing the optimal sensing time and power allocation strategy, in order to maximize the ergodic throughput of the proposed cognitive radio system under two different schemes, namely the wideband sensing-based spectrum sharing scheme and the wideband opportunistic spectrum access scheme. In our analysis, besides the average interference power constraint at primary user, the average transmit power constraint of SU is also considered for the two schemes and then a subgradient algorithm is developed to obtain the optimal sensing time and the corresponding power allocation strategy. Finally, numerical simulations are presented to verify the performance of the two proposed schemes.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.2
• /
• pp.149-154
• /
• 2013

Short term load forecasting for electric power demand is essential for stable power system operation and efficient power market operation. High accuracy of the short term load forecasting can keep the power system more stable and save the power market operation cost. We propose an optimal coefficient selection method for exponential smoothing model in short term load forecasting on weekdays. In order to find the optimal coefficient of exponential smoothing model, load forecasting errors are minimized for actual electric load demand data of last three years. The proposed method are verified by case studies for last three years from 2009 to 2011. The results of case studies show that the average percentage errors of the proposed load forecasting method are improved comparing with errors of the previous methods.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.91-96
• /
• 2019

There are so many low power MAC protocols for wireless sensor network. IEEE802.15.4 among them has disadvantage of a large power consumption for synchronization. To save power consumption it use the superframe operation alternating sleep mode and awake mode. But latency is longer result from superframe operation. Typical asynchronous B-MAC can have shorter latency according to check interval. But transmitter consumes more power because of long preamble. And receiver is suffering from overhearing. In this paper, we propose the adaptive check interval scheme of B-MAC for enhancing the power consumption and delay latency performance. Its power consumption is evaluated by comparing the proposed scheme with a typical IEEE802.15.4.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1530-1535
• /
• 2011

Heat radiation of LED luminaires has risen a problem when applied indoor. LEDs can save energy with higher efficacy than other light sources. However, their heat radiation may increase power consumption for air-conditioning. Therefore, this paper carried out a comparative analysis on the amount of heat radiation for MR16, E26 bulb, and down-light which will be replaced to LED luminaires. Heat amount of LED-MR16 and LED-downlight was 48% and 87.5% lower than that of conventional lamps, halogen MR16 and E26 CFL, respectively. Consequently, the heat amount and indoor temperature were proportional to the power consumption of luminaire. Therefore, the use of LED luminaire can reduce the amount of heat radiation as well as power consumption.

• Journal of Communications and Networks
• /
• v.12 no.5
• /
• pp.480-491
• /
• 2010

Along with the wide acceptance of IEEE 802.11 wireless local area network (WLAN), new applications such as Internet protocol (IP) telephony over WLAN are fast emerging today. For battery-powered IP phone devices, the life time extension is a key concern for the market acceptance while today's 802.11 is not optimized for snch an operation. In this paper, we propose a novel idle mode operation, which comprises paging, idle handoff, and delayed handoff. Under the idle mode operation, a mobile host(MH) without any active session does not need to perform handoff within a predefined paging area (PA). Only when it enters a new PA, an idle handoff is performed. The proposed idle mode allows an MH without traffic to extend its life time. We develop a new analytical model in order to comparatively evaluate our proposed scheme. The numerical resnlts demonstrate that the proposed scheme outperforms the existing schemes with respect to power consumption.