• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.231-236
• /
• 2017

The space harmonics generated by a plane-wave incident upon a multi-layered dielectric grating can undergo strong resonance scattering variations known as GMR(guided-mode resonance). To clarify these effects, we examine the field propagation and dispersion curve inside the grating region by using a rigorous equivalent transmission-line theory(RETT). The results show that, at the peak of a scattering resonance, the reflected mode is almost identical to a leaky wave that can be supported by the grating structure. Thus, we confirm and generalize previous research that has occurred GMR effect associated with the free-resonant character of leaky waves at multi-layered dielectric gratings. Quantitative simulation results illustrating the behavior of typical gratings are given, and the special case of normal incidence is discussed for TM mode.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.173-178
• /
• 2020

A multi-ray model has been used to interpret radio transmission losses in half-canyon structures with slope and to formulate a multi-ray propagation model depending on the angle of slopes. The cut-off angles for the third and fourth paths, which are the slope-sided reflection paths of the transmission and reception radio waves determined by the inclined angles of the slope, were calculated with the height and location of the transmitter and receiver. To predict transmission losses in an inclined plane environment, the embankment environment where the actual slope exists was modeled and simulated to calculate the loss of propagation transmission, and the radio wave transmission loss was confirmed by the measurement for the frequency band 1 to 6 GHz. Simulation results and measurement results showed similar trends in radio transmission loss, and radio transmission loss predictions and measurement results for various terrain information can be used in the design of radio propagation service.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1573-1581
• /
• 1996

This paper present as experimental demonstratio of DSP and a sensory actuator that is used to actively control sound transmission/radiation through a vibrating plate. A plane acoustic wave incident on a clamped, thin circular plate was used as a noise source, and a sensory actuator bounded to the plate was used to control and sense vibration of the plate. The sound transmission reduction problem was tranformed as a structural vibration control problem that actively control the structural vibration modes coupled to acoustic modes. The results show that the first structural vibration mode is controlled with a reduction of 78 percent in the displacement and velocity of the plate. This corresponds to a 13dB reduction in the acoustic response. These experimental results indicate that a sensory actuator bounded to the plate can be employed to attenuate the sound transmitted to radiated from the plate.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.8
• /
• pp.36-44
• /
• 1999

This paper presents the design and fabrication of the duplexer for a Ka-band satellite transponder which is analyzed transmission characteristics by calculating the generalized scattering matrix using mode matching method. It is composed of 2 bandpass filters, coupled with H-plane T-junction having symmetrical inductive iris and E-plane metal insert structures. Compared with the size and weight of the Rx and Tx filter loaded with a transponders respectively, those of the duplexer can be effectively reduced. In a high power transmission, the variation of the filter characteristics is minimized by the scheme that irises are extended to the exterior of H-plane of the waveguide. This scheme needs no extra heat sinks for dissipating high power. The duplexer is designed to improve the simplification, durability and reliability by eliminating tuning screws, which have been used to compensate for the characteristics of fabricated filters. The bandpass filters of the duplexer show the insertion loss of less than 1.2 dB and the return loss in excess of 15 dB. The isolations of more than 65 dB have been achieved between Rx and Tx filter.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2487-2495
• /
• 2000

The acoustic characteristics of expansion chamber will be changed with the variation of inlet/outlet location due to the higher order acoustic mode in a high frequency in which the plane wave theory is not available. In this paper, the acoustic performance of reactive type expansion chamber with circular cross-section is analyzed by using the modified mode matching theory. The sensitivity analysis of four-pole parameters with respect to the location of inlet and outlet is also suggested to increase the acoustic performance. The acoustic power transmission coefficient is used as cost function, and the location of inlet and outlet is used as design variables. The steepest descent method and SUMT algorithm are used for optimization technique. Several results showed that the expansion chamber with optimally located inlet/outlet had better acoustic performance than concentric expansion chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.24-30
• /
• 1998

A directly coupled Boundary Element and Finite Element Model was applied to the dynamic analysis of a coupled acoustic silencer with vibratory wall. In this cupled BEM-FEM muffler model, the BEM model was used to discretize the acoustic cavity and the FEM model was used to discretize the vibratory wall structure. Then the BEM model was coupled with the FEM model. The results of the coupled BEM-FEM model for the dynamic analysis of the simple expansion type reactive muffler configurations with flexible walls were verified by comparing the predicted results to analytical solutions. In order to investigate the effects of the muffler's structural flexibility on its transmission loss(TL) characteristics, the results of the coupled BEM-FEM model in conjunction with the four-pole parameter theory were utilized. The muffler's TL characteristics using the BEM-FEM coupled model with flexible walls as compared to other muffler configurations was studied. Finally the muffler's TL values with respect to different wall's thickness are predicted and compared.

• Journal of the Optical Society of Korea
• /
• v.15 no.3
• /
• pp.283-288
• /
• 2011

In this study, a wide-band photonic crystal Y-splitter for TE modes is proposed. A triangular lattice of air holes etched in a GaAs slab is used as the platform. In order to numerically analyze the structures, plane wave expansion (PWE) and finite difference time domain (FDTD) methods are used. In comparison with the structures reported in the literature, the proposed topology has a less complexity while it provides more than 100nm bandwidth. The simplicity of the design, its high transmission ratio and its wide bandwidth makes it a suitable choice for the implementation of photonic crystal integrated circuits.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.123-128
• /
• 2012

In communication systems, there are various types of microstrip antenna that can be used for many applications. This paper mainly focuses on the simple design of an inset rectangular microstrip patch antenna to operate at a frequency of 2.45 GHz for rectenna design. The study involves using an high frequency structure simulator to design the antenna dimensions and to determine its performance. This antenna is based on a thickness of 1.6 mm flame retardant 4 (FR-4) substrate having a dielectric constant of approximately 4.7, an inset feed, and a ground plane. After simulation, the antenna performance characteristics such as its return loss, voltage standing wave ratio, gain, and radiation pattern were obtained and compared with the fabricated measured antenna.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.6
• /
• pp.787-798
• /
• 1995

We implement the E-plane T-juncition manifold mutiplexer having low insertion loss for output multiplexer of Ku-band satellite transponder. Manifold multiplexer implemented here is composed of 2 channel filters, T-junctions, half-wave waveguide connecting channel filters and manifold, and manifold itself.[1-4] Considering the mass and volume of the satellite transponder, the channel filters are designed to dual-mode.[5-13] And Elliptic filter function is used, which has good characteristics of suppressing the interference between 2 channels. Since the performance of manifold multiplexer depends on the manifold waveguide transmission line length, it's necessary proper analysis. In this paper, we do optimization process of T-junction and other elements by using CAD and implement the manifold multiplexer. An experiment shows that characteristic response of multiplexer matches wel its modeling result.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.6
• /
• pp.748-754
• /
• 1999

The acoustic performance of reactive type single expansion chamber can be calculated theoretically by plane wave theory. But higher order modes should be considered to widen the frequency range. Munjal has suggested the method for analyzing the acoustic properties of simple expansion chamber with taking into consideration of higher order mode of inlet/outlet. But his method cannot predict the acoustic properties exactly when the dimensions of inlet/outlet and expansion chamber have not integer multiples. In this paper the new method was suggested to overcome the shortcomings of Munjal's method The predictions by this method were also compared with those by the finite element method.