• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.204.2-204.2
• /
• 2013

Wide band gap II-VI semiconductors have attracted the interest of many research groups during the past few years due to the possibility of their applications in light-emitting diodes and laser diodes. Among the II-VI semiconductors, ZnO is an important optoelectronic device material for use in the violet and blue regions because of its wide direct band gap (Eg ~3.37 eV) and large exciton binding energy (60 meV). F-doped ZnO (FZO) and undoped ZnO thin films were grown onto quartz substrate by the sol-gel spin-coating method. The doping level in the solution, designated by F/Zn atomic ratio of was varied from 0 to 5 in 1 steps. To investigate the effects of the structure and optical properties of FZO thin films were investigated using X-ray diffraction (XRD), UV-visible spectroscopy, and photoluminescence (PL). In the XRD, the residual stress, FWHM, bond length, and average grain size were changed with increasing the doping concentration. For the PL spectra, the high INBE/IDLE ratio of the FZO thin films doping concentration at 1 at.% than the other samples.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.240-245
• /
• 2004

Tensile properties of hard coating material, TiN, were evaluated using micro-tensile testing system. TiN has been known as a hard coating material commonly used today. Micro-tensile testing system consisted of a micro tensile loading system and a micro-ESPI(Electronic Speckle Pattern Interferometry) system. Micro-tensile loading system had a maximum load capacity of 500mN and a resolution of 4.5 nm in stroke. TiN thin film $1{\mu}m$ thick was deposited on the Si wafer pre-deposited of $Si_3N_4$ film substrate by the closed field unbalanced magnetron sputtering (CFUBMS) process. Three kinds of micro-tensile specimen with the respective width of $50{\mu}m$, $100{\mu}m$ and $500{\mu}m$ were fabricated by MEMS process. The mechanical properties including tensile strength and elastic modulus were determined using the micro-tensile testing system and compared by those obtained by nano-indentation

• 한국세라믹학회지
• /
• 제41권3호
• /
• pp.259-265
• /
• 2004

플라즈마 용사법에 의해 나노크기의 하이드록시 아파타이트 분말을 지르코니아 소결체 기판에 용사한 후 코팅층의 미세조직에 대해 조사하였다. 나노크기의 하이드록시 아파타이트 분말은 Ca(NO$_3$)$_2$$.$4$H_2O$과 (NH$_4$)$_2$HPO$_4$ 용액을 이용한 침전법에 의해 성공적으로 합성되었다. 코팅 후 지르코니아 기판과 코팅층 계면에서 균열은 발생하지 않았으며 코팅층의 두께는 150-250 $\mu\textrm{m}$였다. 나노크기의 하이드록시아파타이트 분말과 용사된 HAp코팅층에서는 비이상적인 상들의 출현이 발견되지 않았다. 80$0^{\circ}C$에서 열처리된 코팅층의 경우 하이드록시 아파타이트 이외에 TTCP와 $\beta$-TCP같은 상이 관찰되었지만 열처리온도 90$0^{\circ}C$에서 TTCP와 $\beta$-TCP상은 소멸되었다. XRD 분석결과, 열처리온도 110$0^{\circ}C$에서 HAp코팅층은 높은 결정화도를 나타내었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.336-336
• /
• 2013

Zinc oxide (ZnO) based transparent oxide semiconductors have been studied due to their high transmittance and electrical conductivity. Pure ZnO have unstable optical and electrical properties at high temperatures but doped ZnO thin films can have stable optical and electrical properties. In this paper, transparent oxide semiconductors of Y-doped ZnO thin films prepared by sol-gel method. The ionic radius of $Y^{3+}$ (0.90 A) is close to that of $Zn^{2+}$ (0.74 A), which makes Y suitable dopant for ZnO thin films. The Sn-doped ZnO thin films were deposited onto quartz substrates with different atomic percentages of dopant which were Y/Zn = 0, 1, 2, 3, 4, and 5 at.%. These thin films were pre-heated at $150^{\circ}C$ for 10 min and then annealed at $500^{\circ}C$ or 1 h. The structural and optical properties of the Y-doped ZnO thin films were investigated using field-emission scanning electronmicroscopy (FE-SEM), X-ray diffraction (XRD), UV-visible spectroscopy, and photoluminescence (PL).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1232-1233
• /
• 2008

딥 코팅 공정을 통하여 콜로이드 $Fe_2O_3$ 나노입자의 단일층을 다공성의 AAO (Anodic Aluminum Oxide) 기판에 형성하였다. 나노입자의 평균 사이즈는 20 nm이고, 각각의 나노입자는 올레익 산(oleic acid) 으로 둘러싸여 옥탄(octane) 용액 안에 분산되어있다. AAO 기판은 알루미늄에 높은 균일성과 고밀도의 기공(pore) 형성을 위해 두 단계 양극산화공정을 통해 제작하였다. AAO 기공의 지름은 ${\sim}$30에서 100 nm 이고, 딥 코팅 공정의 속도는 0.1 mm/sec 로 하여 AAO의 나노기공 안에 나노입자의 단일층을 성공적으로 형성시켰다.

• 비파괴검사학회지
• /
• 제32권3호
• /
• pp.269-275
• /
• 2012

Carbon-fiber reinforced plastic(CFRP) laminates made of nano-particle-coated carbon fibers and damaged by a simulated lightning strike were tested under compression-after-impact(CAI) mode, during which the damage progress due to compressive loading has been monitored by acoustic emission(AE). The impact damage was induced not by mechanical loading but by a simulated lightning strike. Conductive nano-particles were coated directly on the fibers, from which CFRP coupons were made. The coupon were subjected to the strikes with a high voltage/current impulse of 10~40 kA within a few ${\mu}s$. The effects of nano-particle coating and the degree of damage induced by the simulated lightning strikes on AE activities were examined, and the relationship between the compressive residual strength and AE behavior has been evaluated in terms of AE event counts and the onset of AE activity with the compressive loading. The degree of impact damage was also measured in terms of damage area by using ultrasonic C-scan images. The assessment during the CAI tests of damaged CFRP showed that AE monitoring appeared to be useful to differentiate the degree of damage hence the mechanical integrity of composite structures damaged by lightning strikes.

• Nuclear Engineering and Technology
• /
• 제52권10호
• /
• pp.2353-2360
• /
• 2020

An anodic electrophoretic deposition (EPD) technique is used to create a uniform TiO₂ thin film coating on boiling thin steel plates (1.1 mm by 90 mm). All of the effective parameters except time of the EPD method are kept constant. To investigate the effect of gamma irradiation on the critical heat flux (CHF), the test specimens were irradiated in a gamma cell to different doses ranging from 100 to 300 kGy, and then SEM and BET analysis were performed. For each coated specimen, the contact angle and capillary length were measured. The specimens were then tested in a boiling pool for CHF and boiling heat transfer coefficient. It was observed that irradiation significantly decreases the maximum pore diameter while it increases the porosity, pore surface area and pore volume. These surface modifications due to gamma irradiation increased the CHF of the nano-coated surfaces compared to that of the unirradiated surfaces. The heat transfer coefficient (HTC) of the nano-coated surfaces irradiated at 300 kGy increased from 83 to 160 kW/(㎡ K) at 885 kW/㎡ wall heat flux by 100%. The CHF of the irradiated (300 kGy) and unirradiated surfaces are 2035 kW/㎡ and 1583 kW/㎡, respectively, an increase of nearly 31%.

• 한국전기전자재료학회논문지
• /
• 제26권3호
• /
• pp.221-226
• /
• 2013

The water soluble quantum dots (QDs) are synthesized by the phase transfer and silica coating reaction. The photoluminescence intensity of silica-coated QDs are mainly affected by the amount of phase transfer agent, SDS (sodium dodecyl sulfate), and the maximum value is obtained at the cmc (critical micell concentration) concentration of SDS in the phase transfer reaction. Based on fluorescence spectra and field emission transmission electron microscope (FETEM), the energy transfer rate by forster resonance energy transfer (FRET) is increasing with the thickness of the silica shell coated on CdSe/ZnS QDs.

• Korean Chemical Engineering Research
• /
• 제51권2호
• /
• pp.285-291
• /
• 2013

Quartz crystal microbalance (QCM)을 기반으로 기체 흡착센서 시스템을 구성하기 위하여 감지물질, 코팅방법, 희석가스 및 온도의 영향 등이 면밀하게 검토되었다. 특히 주요 대기 오염물질로 알려진 $NO_2$와 $SO_2$를 감지할 수 있도록 polypyrrole과 poly(3,4-ethylenedioxythiophene) 고분자 물질이 코팅된 QCM 센서소자를 구성하였으며, 만들어진 센서소자들은 ppm 수준의 농도에서 두 가스에 대한 높은 선택성과 감도를 보였다. 센서소자의 감지특성과 응답속도는 감지물질의 코팅방법과 코팅량에 크게 의존하였다.

• 대한기계학회논문집A
• /
• 제30권11호
• /
• pp.1425-1432
• /
• 2006

Coating layers on a coated sheet steel frequently affect distributions of strain rate of sheets and deteriorate the frictional characteristics between sheets and tools in sheet metal forming. Thus, it is important to identify the deformation behavior of these coatings to ensure the success of the sheet forming operation. In this study, the technique using nano-indentation test, FE-simulation and Artificial Neural Network(ANN) were proposed to determine the power law stress-strain behavior of coating layer and the power law behavior of extracted coating layers was examined using FE-simulation of drawing and nano-indentation process. Also, deep drawing test was performed to estimate the formability and frictional characteristic of coated sheet, which was calculated using the linear relationship between drawing force and blank holding force obtained from the deep drawing test. FE-simulations of the drawing process were respectively carried out for single-behavior FE-model having one stress-strain behavior and for layer-behavior FE-model which consist of coating and substrate separately. The results of simulations showed that layer-behavior model can predict drawing forces with more accuracy in comparison with single-behavior model. Also, mean friction coefficients used in FE-simulation signify the value that can occur maximum drawing force in a drawing test.