• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.393-396
• /
• 2004

본 논문에서는 완충층용 MgO 박막을 P-type(100)Si 기판위에 작업가스 $Ar:O_2=80:20$, RF 파워 50W, 기판온도 $400^{\circ}C$, 10mtorr의 작업진공에서 $500{\AA}$ 증착하였다. 제작된 MgO/Si 기판위에 RF Magnetron sputtering법으로 작업가스 $Ar:O_2$의 비율을 90:10, 80:20, 70:30으로 변화하면서 $BST(Ba_{0.5}Sr_{0.5}TiO_3)$ 박막을 약 $2000{\AA}$ 증착하였다. XRD 측정결과 작업가스비의 변화에 관계없이(110)BST와 (111)BST 피크만이 관찰되었으며 작업가스 $Ar:O_2=80:20$에서 가장 양호한 결정성을 나타내었다. I-V 측정결과 인가전계 ${\pm}100kV/cm$에서 $10^{-7}A/cm^2$이하의 양호한 누설전류 특성을 보여주고 있으며 C-V 측정결과 작업가스 $Ar:O_2$의 비율 90:10, 80:20, 70:30에서의 비유전율은 각각 283, 305, 296으로서 작업가스비 80:20에서 제작된 박막의 특성이 가장 우수하였다. 작업가스비 80:20에서 제작된 박막의 SEM 측정결과 결정이 성장되었음을 확인할 수 있었고 그레인의 크기는 약 10nm였다.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.56-62
• /
• 1997

Using a rf-magnetron sputtering method, highly c-axis oriented La modified $PbTiO_{3}$ (PLT) ferroelectric thin films with compositions of $(Pb_{1-x}La_{x})Ti_{1-x/4}O_{3}$, where x=0.05, x=0 and x=0.15, have been obtained on (100)MgO single crystal substrate under conditions of low gas pressure. The degree of c-axis orientation of PLT films decreases with increasing gas pressure and with increasing La contant. These films were characterized by X-ray diffraction and SEM. PLT thin films of x=0.05, 0.1 and 0.15 show a low dielectric constant of 218, 246 and 361 at 1 kHz and remanent polarization(Pr) of $9{\mu}C/cm^{2}$, $8{\mu}C/cm^{2}$ and $7{\mu}C/cm^{2}$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.80-84
• /
• 2014

The discharge characteristics of Surface Dielectric Barrier Discharge (SDBD) reactor are investigated to find optimal driving condition with adjusting various parameter. When the high voltage with sine wave form is applied to SDBD source, successive pulsed current waveforms are observed owing to multiple ignitions through the long discharge channel and wall charge accumulation on the dielectric surface. The discharge voltage, total charge between dielectrics, mean energy and power are calculated from measured current and voltage according to electrode gap and dielectric thickness. Discharge mode transition from filamentary to diffusive glow is observed for narrow gap and high applied voltage case. However, when the diffusive discharge is occurred with high applied voltage, the actual firing voltage is always lower than that with low driving voltage. The $Si_3N_4$, $MgF_2$, $Al_2O_3$ and $TiO_2$ are considered for dielectric protection and high secondary electron emission coefficient. SDBD with $MgF_2$ shows the lowest breakdown voltage. $MgF_2$ thin film is proposed as a protection layer for low voltage atmospheric dielectric barrier discharge devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.41-44
• /
• 1998

Dual mode resonators were fabricated using high temperature superconductor. The deposited material was $Y_1Ba_2Cu_3O_{7-x}$(YBCO) on MgO(100) substrate using pulsed laser deposition. Dual mode resonators were patterned by standard photolithography process and wet etching. At the back-side of the substrate, the ground plane with the metal layer of Ti and Ag was fabricated. The transition temperatures of YBCO films were 85-88 K, and network analyzer was used for testing the performance of the resonators. The input/output feedline angles of each resonator were $60^{\circ}$and $100^{\circ}$. The resonant frequency of resonators was 10 GHz. In this paper, dual mode resonator was fabricated for the application of satellite communication.

• Korean Journal of Materials Research
• /
• v.16 no.10
• /
• pp.606-613
• /
• 2006

This study was purposed to evaluate the influence of anodically oxidized film on titanium (Ti) onto MG-63 osteoblast-like cell attachment and activity. Only scratch lines created by polishing were seen in ASR and ANO-1 groups. About $1.5{\mu}m$-thick homogeneous oxide film which has pores of about $0.5{\mu}m$ diameter were formed in ANO-12. The crystalline structure of the oxide films formed by anodization in phosphoric acid electrolyte was $TiP_2O_7$. The total protein amounts of ANO-1 and ANO-12 groups showed higher values of maximum protein amount than that of AS-R group. At 3 days of incubation, total protein amount showed higher value in ANO-2 when comparing to that of AS-R (p<0.05). Based on the results of ALPase activity test, the degree of MG-63 cell differentiation for initial mineralization matrix formation was similar. For all the test groups after 1 day of incubation, MG-63 cells grew healthily in mono-layer with dendritic extensions. After incubation for 3 days, the specimen surfaces were covered more densely by cells, and numerous micro filaments were extruding to the extracellular matrix.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.325-325
• /
• 2008

스크린 프린팅에 의한 압전 후막은 MEMS 공정을 이용하여 마이크로 펌프, 마이크로 벨브, 마이크로 센서, 마이크로 로봇 등 여러 초소형 기계부품에 응용되고 있으며, Sol-Gel, PLD를 이용해 증착된 막 등에 비해 수십${\mu}m$의 비교적 두꺼운 막을 형성시킬 수 있는 장점을 가지고 있다. 그러나 실리콘 기판을 사용하여 스크린 프린팅으로 형성된 압전 후막의 경우, 공정상 바인더를 연소시키는 과정을 거치게 되므로, 밀집된(Dense) 구조를 가지는 막을 만들기가 어렵다. 이로 인해 스크린 프린팅에 의한 후막은 전기적 특성 및 기계적 특성이 떨어지는 경향이 있다. 본 연구에서는 스크린 프린팅에 의한 압전 후막의 밀집된 구조 및 특성을 향상시키기 위해 0.01Pb$(Mg_{1/2}W_{1/2})$O3-0.41Pb$(Ni_{1/3}Nb_{2/3})O_3-0.35PbTiO_3-0.23PbZrO_3$의 powder와 Attrition 밀링 처리된 powder를 비율별로 혼합하여 입자의 크기를 변화시켜 막의 충진 밀도를 향상시켰으며, 열처리 효과를 극대화시키기 위해 RTA(Rapidly Thermal Annealing)를 통해 열처리 하였다. Attrition 밀링에 의한 파우더를 각각 비율별로 100%, 50%, 25%로 혼합하여 만든 압전 세라믹 페이스트는 P-type(100)Si Wafer sample 위에 $1{\mu}m$의 하부전극용($1100^{\circ}C$) Ag 전극을 screen print하여 소결했다. 그리고 다시 전극이 형성된 Si wafer 위에 스크린 프린팅하고, 건조 한 후 RTA로 300초 동안 열처리 한 결과 밀집된 구조를 가지는 압전 후막을 제작 수 있었다.

• Korean Journal of Materials Research
• /
• v.5 no.5
• /
• pp.598-605
• /
• 1995

Thin films of $YB_{2}Cu_{3}O_{7-d}$ were prepared on various substrated of MgO(100), $SrTiO_{3}$, and $LaAlO_{3}$ by using off-axis magentron sputtering methods and annealing in-situ. The prarameters of film fabrication processes had been optimized through a "follow the lcoal maxima" strategy to yield good quality films in therms of the critical temperature $T_{c}$ and the critical current density $J_{c}$. Optimizedproecsses employing a plane magndtron and an cylindrical magnetron yielded $T_{c}$>90K along with $J_{c}$$10^{6}$A/$\textrm{cm}^2$ at 77K and > 2${\times}$$10^{7}$A/$\textrm{cm}^2$ at 5K. The sampels, however, showed degradationinthe properties, after chemical etching for fabrication of microbridges with the line width of 2-10 mocrons. In particular, the value of $T_{c}$ for the microbridges of 2microns was as small as 80%. The degradation was strongly dependent on the line width through a formula : $T_{c}$(e)=$T_{c}$)b) [1-a exp(-1000 bL)} where $T_{c}$(e) and $T_{c}$ (b) are the values of $T_{c}$ in the absolute scale measured after and before chemical etching, respectively and L is the line width in mm. By utilizing a best fitting technique, the proper constant values of a and to b were found as exp(-1.2) and 0.22, respectively. This formula was very useful in estimatiing the upper limit of the device operationtemperature.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.24 no.2
• /
• pp.41-48
• /
• 2018

A printable time temperature integrator (TTI) consisting of oxygen indicator and cover films with various oxygen permeability was developed. The printing ink contained methylene blue (oxygen indicator) which changed in color during storage. $TiO_2$ and glycerol for UV-activation of TTI and zein and ethanol for printing performance were also contained in the printing ink. The cover film on the ink was employed to control the color change rate and temperature dependency (Arrhenius activation energy, $E_a$) by using the different films (PE, PET, OPP, and LLDPE). The film properties were varied by annealing. TTI was produced by silk screen printing. As a result, the color change rates were different for the cover films, being the highest in TTI with LLDPE, followed by OPP, PE, and PET. The rate decreased with increase in the cover film thickness. The $E_a$ was the highest in TTI with LLDPE, followed by OPP, PE, and PET. The $E_a$ did not change with the cover film thickness. The annealed PVC and PET film were lower in oxygen permeability than the unannealed ones, indicating the lower color change rate.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.3
• /
• pp.124-128
• /
• 2020

Recently, many studies on growth of single crystal diamond using MPECVD have been conducted. The heteroepitaxial method is one of the methods for growing diamonds on a large-area substrate, and research on synthesis of single crystal diamonds using SrTiO₃, MgO, and sapphire substrates has been attempted. In addition, research is being conducted to reduce the internal stress generated during diamond growth and to improve the crystallinity of the diamond. The compressive stress generated therein causes peeling and bowing from the substrate. This study aimed to synthesize heteroepitaxial single crystal diamonds with high crystallinity by surface modification. A diamond thin film was first grown on a sapphire/Ir substrate by MPECVD, and then etched with H₂ gas to modified the morphology and roughness of the surface. A secondary diamond layer was grown on the surface, and the internal stress, crystallinity of the diamond were investigated. As a result, the fabrication of single crystal diamonds with improved crystallinity was confirmed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.151-151
• /
• 2012

A new plasma process, i.e., the combination of PIII&D and HIPIMS, was developed to implant non-gaseous ions into materials surface. HIPIMS is a special mode of operation of pulsed-DC magnetron sputtering, in which high pulsed DC power exceeding ~1 kW/$cm^2$ of its peak power density is applied to the magnetron sputtering target while the average power density remains manageable to the cooling capacity of the equipment by using a very small duty ratio of operation. Due to the high peak power density applied to the sputtering target, a large fraction of sputtered atoms is ionized. If the negative high voltage pulse applied to the sample stage in PIII&D system is synchronized with the pulsed plasma of sputtered target material by HIPIMS operation, the implantation of non-gaseous ions can be successfully accomplished. The new process has great advantage that thin film deposition and non-gaseous ion implantation along with in-situ film modification can be achieved in a single plasma chamber. Even broader application areas of PIII&D technology are believed to be envisaged by this newly developed process. In one application of non-gaseous plasma immersion ion implantation, Ge ions were implanted into SiO2 thin film at 60 keV to form Ge quantum dots embedded in SiO2 dielectric material. The crystalline Ge quantum dots were shown to be 5~10 nm in size and well dispersed in SiO2 matrix. In another application, Ag ions were implanted into SS-304 substrate to endow the anti-microbial property of the surface. Yet another bio-application was Mg ion implantation into Ti to improve its osteointegration property for bone implants. Catalyst is another promising application field of nongaseous plasma immersion ion implantation because ion implantation results in atomically dispersed catalytic agents with high surface to volume ratio. Pt ions were implanted into the surface of Al2O3 catalytic supporter and its H2 generation property was measured for DME reforming catalyst. In this talk, a newly developed, non-gaseous plasma immersion ion implantation technique and its applications would be shown and discussed.