• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.583-585
• /
• 2004

In this paper we will deal with a calibration method for low cost motion capture system using psd(position sensitive detection) optical sensor. To measure the incident direction of the light from LED emitted marker, the PSD is used the output current ratio on the electrode of PSD is proportional with the incident position of the light focused by lens. In order to defect the direction of the light, the current output is converted into digital voltage value by opamp circuits peak detector and AD converter with the digital value the incident position is measured. Unfortunately, due to the non-linearly problem of the circuit poor position accuracy is shown. To overcome such problems, we compensated the non-linearly by using least-square fitting method. After compensated the non-linearly in the circuit, the system showed more enhanced position accuracy.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.18 no.4
• /
• pp.21-29
• /
• 2010

The main purpose of this study is to obtain linear models for the design of automatic flight controller in order to operate the Light Sport Aircraft as unmanned air vehicle. Flight test equipments installed on the aircraft to acquire flight test data are described and maneuvers for practical speed calibration are introduced. Parameters for the linear models of lateral and longitudinal motion are estimated by the Output error method as well as trim data analysis using the flight test data. Simulated data using the estimated parameters is shown to agree well with the measurement data. Estimated parameters obtained for several flight conditions can be used to improve the aerodynamic database of the simulation program.

• Journal of the Optical Society of Korea
• /
• v.19 no.1
• /
• pp.74-79
• /
• 2015

A novel color clustered optical RGB multiple-input multiple-output (MIMO) system is presented. As visible light can be divided into three primary regions of red, green and blue, data can be modulated and transmitted separately using these three color clusters. Each color cluster comprised of 30 RGB LEDs is modulated using on-off-keying (OOK), and selection combining is performed at the receiver, producing a diversity effect within that color cluster. The simulations demonstrate that the proposed RGB MIMO VLC system provides high performance via a relatively simple design of MIMO. Moreover, the proposed system ensures sufficient illumination from LEDs and offers extended distance if more LEDs are applied.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.2
• /
• pp.55-60
• /
• 2006

In order to suppress lasing oscillation and obtain high light power, We have proposed a novel SLD which is formed with a straight and tilted waveguide. The window region is used to suppress lasing oscillation and reduce the facet reflectivity. High power and low reflectivity is obtained by the straight and tilted waveguide. Based on the theoretical analysis, we have fabricated the SLD with the waveguide of 500 $\mu$m length and window region of 50 $\mu$m by LPE equipment. Through the measurements of optical characteristics, the output light power of 3 mW was obtained at the 150 mA CW injection current and 25$^{circ}C$. We have confirmed that the proposed SLD has a 0.8 dB spectrum ripple lower than 1 dB which is sufficiently low reflectivity for preventing lasing.

• Journal of Information Display
• /
• v.2 no.4
• /
• pp.46-51
• /
• 2001

Using ray-optics code incorporated with three-dimensional PDP cell simulation, we have analysed the energy flow in the PDP cell from the electric power input to the visible light output. Also, the visible light output profile and viewing angle distribution were obtained. We applied our code to the analysis of the barrier rib height effect on the visible light luminance and efficiency of the sustaining discharge. Although cells with higher barrier rib generate more VUV photons, less ratio of visible photons are emitted toward front panel due to the shadow effect. Thus, there exists optimal barrier rib height giving the highest visible luminance and efficiency. This kind of code can be a powerful tool in designing cell geometry.

• Journal of the Optical Society of Korea
• /
• v.16 no.3
• /
• pp.292-298
• /
• 2012

The epitaxial layer structures for blue InGaN light emitting diodes have been optimized for high brightness applications with the output power levels exceeding 1000 $W/cm^2$ by using a self-consistent finite element method. The light-current-voltage relationship has been directly estimated from the multiband Hamiltonian for wurtzite crystals. To analyze the efficiency droop at high injection levels, the major nonradiative recombination processes and carrier spillover have also been taken into account. The wall-plug efficiency at high injection levels up to several thousand $A/cm^2$ has been successfully evaluated for various epilayer structures facilitating optimization of the epitaxial structures for desired output power levels.

• The Journal of the Korean dental association
• /
• v.57 no.3
• /
• pp.175-184
• /
• 2019

Increasing the aesthetic needs of patients and decreasing the use of amalgam had led to increased demand for dental resin composite. Thereby, light curing unit (LCU) has become an essential equipment in dental clinic. To ensure long-term prognosis of photopolymerized materials, LCU should have a uniform and consistent radiant output and an emission spectrum that includes the active wavelength range of photoinitiators. In addition, when the correct use and thorough maintenance and repair of LCU are performed, the higher success rate of restoration using photopolymerization materials will be achieved.

• Journal of Biosystems Engineering
• /
• v.38 no.3
• /
• pp.208-214
• /
• 2013

Purpose: Performances of a tractor diesel engine fueled by three different animal fats biodiesels were evaluated comparing with light oil tractor in terms of power, fuel consumption rate, exhaust gases, particulate matter amount and field work capacity. Methods: Animal fats based on pig biodiesel were manufactured manually and tested for its engine performance in the tractor diesel engine and fuel adoptability in the field works. Four different fuels, three different content of biodiesel (BD20, BD50, BD100) and light oil, were prepared and tested in the four strokes diesel engine. Power output, fuel consumption rate and exhaust gases of the four fuels in the diesel engine were compared and discussed. Results: Power output of light oil engine was the greatest showing 5.3% difference between light oil and BD100, but 0.37% better power than BD20 engine power. Less exhaust gases of $CO_2$, CO, $NO_X$ and THC were produced from animal fats biodiesel than light oil, which confirmed that biodiesel is environmental friendly fuel. For fuel adoptability in the tractor, biodiesel engine tractor showed its fuel competitiveness comparing with light oil for tractor works in the faddy field. Conclusions: With four different fuel types of animal-fats biodiesel, performances of a four cylinder diesel engine for tractor were evaluated in terms of power, exhaust gases, particulate matters (PM) and field work capacity. No significant differences observed in the engine performances including power output and exhaust gases emission rate. No significant power difference observed between the various fuels including light oil on the engine running, however, amounts of noxious exhaust gases including $CO_2$ and $NO_X$ decreased as biodiesel content increased in the fuels. Field performances of animal-fats biodiesel tractor were investigated by conducting plowing and rotary operation in the field. Tilling and rotary performance of light oil tractor and BD20 tractor in the field were compared, in which about 10% travelling speed difference on both operations were monitored that showed light oil tractor was superior to BD20 tractor by 10%. Animal-fats can be an alternative fuel source replacing light oil for agricultural machinery and an environmental friendly fuel to nature.

• Proceedings of the KIEE Conference
• /
• 2003.07e
• /
• pp.70-74
• /
• 2003

The buck-boost converter is employed as the variable output PFC power stage. From the loss analysis, this topology has a high efficiency from light load to heavy load. A modified input current sensing scheme is presented to overcome the problem of the insufficient phase margin for the PFC circuit near the maximum output voltage. The variable output PFC circuit has a good performance in the wide output voltage range, under both the Boost mode when the output voltage is high and the Buck+Boost mode when the output voltage is low.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.48-55
• /
• 2016

Ambient-light sensor system, which changes the brightness of a display as ambient light change, was studied to reduce the power consumption of the mobile applications such as note PC, tablet PC and smart phone. The ambient-light sensor system should be integrated on a display panel to improve the complexity and cost of mobile applications, so the ambient-light sensor and readout circuit was integrated on a display panel using low-temperature poly-silicon thin film transistors (LTPS-TFT). We proposed the new compensation method to correct the panel-to-panel variation of the ambient-light sensors, without additional equipment. We designed and investigated the new readout circuit with the proposed compensation method and the analog-to-digital converter for the final digital output of ambient light. The readout circuit has very simple structure and control timing to be integrated with LTPS-TFT, and the input luminance ranges from 10 to 10,000 lux. The readout rate is 100 Hz, and maximum differential non-uniformity with 20 levels of the final output below 0.5 LSB.