• International Journal of Railway
• /
• v.7 no.1
• /
• pp.16-23
• /
• 2014

Reduction in railway-induced vibrations in urban areas is a very challenging task in railway transportation. Many mitigation measures can be considered and applied. Among these, a little attention has been paid to trenches. In this study, a numerical investigation on the effectiveness of in-filled trenches with pipes in reducing railway vibrations due to passing trains is presented. Particularly, a series of two-dimensional dynamic analysis was performed to model the behavior of ballasted railway track under harmonic load with ABAQUS software as a Finite Element method. In so doing, two types of in-filled trenches with pipes with steel and concrete materials have been investigated in this paper. In addition, effectiveness of pipes made of steel and concrete, filled with loose sand and clay in railway-induced vibration reduction has been assessed. The results point out that using in-filled trench with pipes does not effective a lot on railway-induced vibration reduction in comparison to other railway-induced vibration reduction methods. However, in-filled trenches with steel pipes are much more effective than in-filled trenches with concrete pipes. Moreover, filling pipes with loose sand and clay does not have any effect on vibration reduction efficiency of these in-filled trenches.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.100-108
• /
• 1999

rectangular open or in-filled trenches(concrete and rubber) are often used to reduce the ground vibrations caused by propagating surface(Rayleigh) waves. This paper presents the experimental data for estimating the vibration screening effectiveness of open or in-filled trenches Field dynamic tests using the exciter which can generate the 100kN vertical cyclic load in the range of 100-250 Hz were performed. One hundred and twenty accelerometers to measure the ground response are used in 6 radial direction. To compare the effectiveness of the vibration isolation the contours of the amplitude ratio with the dimensionless parameters dividing by Rayleight wave lengths were presented.

• Structural Engineering and Mechanics
• /
• v.11 no.5
• /
• pp.503-518
• /
• 2001

In this paper, the procedure for deriving an infinite element that is compatible with the quadrilateral Q8 element is first summarized. Enhanced by a self mesh-expansion procedure for generating the impedance matrices of different frequencies for the region extending to infinity, the infinite element is used to simulate the far field of the soil-structure system. The structure considered here is of the box type and the soils are either homogeneous or resting on a bedrock. Using the finite/infinite element approach, a parametric study is conducted to investigate the effect of open and in-filled trenches in reducing the structural vibration caused by a train passing nearby, which is simulated as a harmonic line load. The key parameters that dominate the performance of wave barriers in reducing the structural vibrations are identified. The results presented herein serve as a useful guideline for the design of open and in-filled trenches concerning wave reduction.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1998.04a
• /
• pp.106-112
• /
• 1998

A numerical experiment is conduced to study the wave screening effectiveness of wave barriers which are constructed to reduce the ground-transmitted vibration. The finite element method is used for the simulation of the wave propagation behavior. In order to reduce the computational burden the absorbing boundary's one employed. Validity of the numerical model is checked by comparing the results with the published data. The screening effectiveness of the in filled trenches is then studied for different trench dimensions and material properties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.3
• /
• pp.228-233
• /
• 2001

This paper presents the optimized design, fabrication and thermal characteristics of micro-heaters for thermal MEMS (micro elelctro mechanical system) applications usign SOI (Si-on-insulator) and trench structures. The micro-heater is based on a thermal measurement principle and contains for thermal isolation regions a 10㎛ thick Si membrane with oxide-filled trenches in the SOI membrane rim. The micro-heater was fabricated with Pt-RTD (resistance thermometer device) on the same substrate by suing MgO as medium layer. The thermal characteristics of the micro-heater wit the SOI membrane is 280$\^{C}$ at input power 0.9W; for the SOI membrane with 10 trenches, it is 580$\^{C}$ due to reduction of the external thermal loss. Therefore, the micro-heater with trenches in SOI membrane rim provides a powerful and versatile alternative technology for improving the performance of micro-thermal sensors and actuators.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.569-572
• /
• 2000

This paper presents the optimized fabrication and thermal characteristics of micro-heaters for thermal MEMS applications using a SDB SOI substrate. The micro-heater is based on a thermal measurement principle and contains for thermal isolation regions a 10$\mu\textrm{m}$ thick silicon membrane with oxide-filled trenches in the SOI membrane rim. The micro-heater was fabricated with Pt-RTD(Resistance Thermometer Device)on the same substrate by using MgO as medium layer. The thermal characteristics of the micro-heater with the SOI membrane is 280$^{\circ}C$ at input Power 0.9 W; for the SOI membrane with 10 trenches, it is 580$^{\circ}C$ due to reduction of the external thermal loss. Therefore, the micro-heater with trenches in SOI membrane rim provides a powerful and versatile alternative technology for improving the performance of micro thermal sensors and actuators.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.197-201
• /
• 2002

This paper presents optimized design, fabrication and thermal characteristics of micro-heaters for thermal MEMS (micro electro mechanical system) applications using SOI and trench structures. The micro-heaters are based on a thermal measurement principle and contains thermal isolation regions of 10 ${\mu}m$-thick Si membranes consisting of oxide-filled trenches in the SOI membrane rim. The micro-heaters were fabricated with Pt-RTD on the same substrate via MgO buff layer between Pt thin-film and $SiO_2$ layer. The thermal characteristics of micro-heater with trench-free SOI membrane structure was $280^{\circ}C$ at input power 0.9 W; in the presence of 10 trenches, it was $580^{\circ}C$ due to reduction of the external thermal loss. Therefore, a micro-heater with trenches in SOI membrane rim structure provides a powerful and versatile alternative technology for enhancing the performance of micro-thermal sensors and actuators.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.6
• /
• pp.41-49
• /
• 2004

In general, open trenches or in-filled trenches have been used to isolate transmitting of vibration. Recently alternative methods, in which various materials are used for wall barriers have been proposed and performed in several sites. Although the effects of these methods are verified, resonable and qualitative evaluation methods have not yet been conducted. It may be because many factors, such as the characteristics of vibration sources, ground condition, and parameters of wall barrier are coupled complicatedly. In this study, a series of centrifugal modelings were conducted in order to examine the evaluation method of a vibration wall barrier when point load transmits to the surface. The experiments were performed with different stiffness of wall barriers and different depths of installations. Using the results obtained from tests, effects of those variables on the efficiency of vibration barrier were analyzed. Through this investigation we observed vibration transmission of under ground, and verified the applicability of ball dropping system which was developed in this study.

• Journal of the Korean Vacuum Society
• /
• v.11 no.4
• /
• pp.235-239
• /
• 2002

A new method for deep trench isolation using selective growth of polycrystalline silicon is proposed. In this method, trench filling is performed by forming polysilicon-inner sidewalls within the trench, and then selectively growing them by reduced chemical vapor deposition using $SiH_2C1_2$gas at $1100^{\circ}C$. The surface profiles of filled trenches are determined mainly by the initial depth of inner sidewalls and the total thickness of selective growth. No chemical mechanical polishing(CMP) process is needed in this new method, which makes the process flow simpler and more reliable in comparison with the conventional method using CMP process.

• The Journal of Korean Medical History
• /
• v.34 no.1
• /
• pp.31-46
• /
• 2021

Shin Hong-Gyun and his family have been in medicine for many generations as Korean Medical Doctors (KMDs). In 1919 when Shin Hong-Gyun was participating in an independence movement in Jang-Baek-Hyun, his younger brother Shin Dong-Gyun was killed by Japanese military police forces. This tragic incident triggered Shin Hong-Gyun to establish an army for national independence called , holding 200 young men, to serve in armed struggle against the Japanese Government with Kim Jung-Geon in May, 1920. In March 1933, Shin Hong-Gyun, as a military surgeon, led his men to the Korean Independence Army to fight a battle. Once he became a member of the Korean Independence Army, he, in fact, participated in few battles: Sadohaja, Dong-Kyung-Sung, Deajeonjayeong. Daejeonjayeong was a waypoint that the Japanese military needed to pass through in order to reach the Wangcheong area. Shin Hong-Gyun's independence forces had to endure painful starvation and heavy rain while hiding in ambush for long periods of time until the Japanese military would appear. Due to its summer rainy season, rainwater overflowed into their trenches and was filled up to the waist. Even worse, food stockpiles were low and the Japanese army did not appear for longer time. Shin Hong-Gyun's entire team suffered severe hunger and extreme cold. At this critical moment, Shin Hong-Gyun used his expertise as a KMD to find edible black mushrooms that grow wild in the mountains and use them to feed his men. This event led to the victory of the independence army at the battle of Daejeonjayeong. The purpose of the paper is to inform and highlight the forgotten history of Shin Hong-Gyun who was, both, a Korean Medical Doctor and a military surgeon.