• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권7호
• /
• pp.339-342
• /
• 2005

We present a new high-frequency equivalent circuit model for 52pin QFP used in typical IC's and extract R, L, and C values of this circuit model using a 3-D E & M field simulator. Futhermore, L and C value variations as a function of Pin number due to the shape differences of the leads have been fitted to 2nd order polynomials in order to extend the applicability of this model.

• KEPCO Journal on Electric Power and Energy
• /
• 제6권4호
• /
• pp.473-480
• /
• 2020

In this paper, we proposed a high frequency equivalent circuit considering parasitic impedance components for differential noise analysis on the input stage during DC-DC buck converter switching operation. Based on the proposed equivalent circuit model, we presented a method to measure parasitic impedance parameters included in DC bus plate, IGBT, and PCB track using the gain phase method of a network analyzer. In order to verify the validity of this model, a DC-DC prototype consisting of a buck converter, a signal analyzer, and a LISN device, and then resonance frequency was measured in the frequency range between 150 kHz and 30 MHz. The validity of the parasitic impedance measurement method and the proposed equivalent model is verified by deriving that the measured resonance frequency and the resonance frequency of the proposed high frequency equivalent model are the same.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권1호
• /
• pp.27-32
• /
• 2003

The thesis is used by PSpice circuit model to the characteristics of a fluorescent lamp modified form of he classical Cassie and Mayr equations in order to show the characteristics of HID(High-Intensity Discharge) Lamp. This is useful for applying high-frequency electric ballast for HID Lamp, and show that the result of experimentations and simulations, such as lamp rating, input voltage, high-frequency electric ballast which is using the ABM circuit model of the low pressure sodium lamp, come to the voltage and current wave.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.1-5
• /
• 2000

This paper deals with the modeling and analysis of the high voltage flyback transformer (HVFBT) often utilized in small-sized high voltage DC power supplies. The parasitic capacitance of th HVFBT with the large turns of the secondary winding causes the undesirable parasitic resonance in the transient state which produces the high current stress and limits the switching frequency of the converter. In order to analyze this phenomenon the equivalent circuit model including the parasitic capacitance is derived and the frequency characteristics are provided. The parasitic resonance in the switching states is also investigated based on this equivalent circuit model. The derived model and analysis is finally validated through the SPICE simulation and experiments.

• 한국산업융합학회 논문집
• /
• 제20권5호
• /
• pp.419-424
• /
• 2017

The purpose of this study is to develop a virtual testbed capable of predicting the functional performance of a linear electromagnetic actuator for a high voltage relay in order to reduce its development costs and time. The virtual testbed is defined by a multiphysics coupling approach in order to consider the complex interactions of multi-domains such as the solenoid model of electromagnets, the mass-spring-damper model of mechanical systems, the electric circuit model for an external control unit, and the thermal model for predicting temperature variations. The performances of the existing high voltage relay were estimated by the virtual testbed, and then the effectiveness and validation of the proposed testbed were discussed in comparison with the experimental test results. This study showed that the virtual testbed can be applied in design, optimization, and investigation of high voltage relays.

• 전기학회논문지P
• /
• 제56권3호
• /
• pp.148-154
• /
• 2007

In this paper, characteristics of ignition voltage and current by wire length of HID(High Intensity Discharge) lamp circuit are analyzed. In the construction field, decision of the wire thickness for HID lamp circuit has the problems, and these are presented. Through transmit parameters, equivalent model of the ballast and HID lamp circuit was derived. The graph of voltage reduction about length between the ballast and the lamp is shown. The simulation of proposed model and experimental results are presented in order to validate the proposed method. The proposed model and graph can use to choose the proper length of wire between the ballast and the lamp in the field.

• 한국초전도ㆍ저온공학회논문지
• /
• 제23권4호
• /
• pp.44-48
• /
• 2021

In order to obtain ultra-high resolution MRI images, research and development of 11 T or higher superconducting magnets have been actively conducted in the world, recently. The high-temperature superconductor (HTS), first discovered in 1986, was very limited in industrial application until mid-2010, despite its high critical current characteristics in the high magnetic field compared to the low-temperature superconductor. This is because HTS magnets were unable to operate stably due to the thermal damage when a quench occurred. With the introduction of no-insulation (NI) HTS magnet winding technology that does not burn electrically, it could be expected that the HTS magnets are dramatically reduced in weight, volume, and cost. In this paper, a 6 T-class NI HTS magnet for basic characteristic analysis was designed, and a distributed equivalent circuit model of the NI coils was configured to analyze the charging current characteristics caused by excitation current, and the charge delay phenomenon and loss were predicted through the development of a simulation model. Additionally, the critical current of the NI HTS magnets was estimated, considering the magnetic field, its angle and temperature with a given current. The loss due to charging delay characteristics was analyzed and the result was shown. It is meaningful to obtain detailed operation technology to secure a stable operation protocol for a 6T NI HTS magnet which is actually manufactured.

• 한국전자파학회논문지
• /
• 제17권8호
• /
• pp.753-759
• /
• 2006

일반적으로 소형 안테나의 효율 측정에는 Wheeler cap 측정법이 많이 사용되지만 이 방법은 안테나의 동작 원리가 복잡할 경우 정확한 효율을 측정할 수 없는 단점이 있다. 그러나 고차 회로를 이용하여 안테나의 입력 임피던스를 정확히 나타낼 수 있으면 보다 정확한 안테나의 효율 측정이 가능하다. 본 논문에서는 변압기 회로를 이용하여 보다 쉽게 고차 회로를 구성할 수 있는 고차 회로 모델 구성법과 이를 최적화하는데 소요되는 시간단축과 정확성 향상을 위한 각 소자 값들의 효과적인 초기 값 설정 방법을 제안하였다. 고차 회로 모델의 각 소자 값들을 최적화하기 위해 유전자 알고리즘을 이용하였으며, 제안된 방법을 수동형 RFID 태그 안테나의 효율 측정을 통해 검증하였다.

• 전자공학회논문지SC
• /
• 제39권2호
• /
• pp.146-156
• /
• 2002

이 논문에서는 불규칙한 배선 구조에 대한 가상직선(virtual-straight line) 파라미터 추출 방법과 이를 이용한 새롭고 빠른 시간 영역에서의 시뮬레이션 방법론을 보이고 검증한다. 비선형인 트랜지스터의 특성을 고려한 인터컨넥트 회로의 시간영역에서의 신호응답은 모델차수감소법(model order reduction method)을 사용하여 수행된다. 모델차수감소법은 인터컨넥트 회로의 단위길이당 파라미터를 이용하므로 인터컨넥트의 길이가 서로 다르고 불규칙한 형태를 갖는 인터컨넥트에 대해서 직접적으로 모델차수감소법을 적용하기 위해 가상직선 모델을 사용하여 인터컨넥트의 파라미터를 추출한다. 또한 모델차수감소법은 일반적인 Berkeley SPICE의 모듈로 구성하여 인터컨넥트 회로의 시간영역 시간응답을 구하였으며 일반적인 회로 시뮬레이터인 HSPICE의 시뮬레이션 결과와 비교하여 잘 일치한다는 것을 보인다. 제안된 방법은 복잡한 다층 배선 구조에 대한 신속하고 정확한 시간영역 신호응답을 제공함으로써 고성능 VLSI 회로 설계에 유용하게 적용할 수 있다.

• 전기학회논문지
• /
• 제61권2호
• /
• pp.263-269
• /
• 2012

In order to present that the electromagnetic compatibility standards following the frequency goes up which is based automotive electronics, in this paper, a hybrid/electric vehicle battery which reflects the frequency of the equivalent circuit model is introduced. By using this circuit modeling, the impedance characteristics can be analysed and an analyze of battery one cell is finished. Using this model, each different from the discharging situation, the discharge characteristic curve could be led. Basic theoretical approaches and measuring results through MATLAB and experimental validation of the EIS measurement equipment was used.