• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1991.10a
• /
• pp.17-22
• /
• 1991

An accurate and efficient analytical model describing the bond effect between reinforcing steel and concrete without taking the double nodes is presented. To increase the efficiency of the solution and reduce the number of degrees of freedom, the reinforcing bar elements are considered to be embedded in the connote elements. Relative douses of freedom accounting for the relative slip between reinforcing steel and concrete are condensed out during the stiffness formation phase. However, these degrees of freedom Can be taken into account explicitly by solving the constructed global equilibrium equation for each reinforcing steel. The usefulness of proposed model is established through the comparison with the experimental data subjected on push and push-pull loadings.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.403-406
• /
• 1999

Although infilled wall considered as a non-structural element, the infilled applied in reinforced concrete frame structural systems represents an important element influencing the behaviour and the stability of a structure under seismic effect. This research is performed an experimental investigation of gravity-load designed single-stroy, single-bay, low-rise nonseismic moment-resisting reinforced concrete frame 2 dimension specimens to evaluate the effect of seismic capacity. For pseudo static test, it was manufactured one half scale specimens of two types (Bare Frame, Infilled Frame) based on typical building. The results of these experiments provided regarding the global as well as the local responses of 1) Crack pattern and failure modes, 2) Stiffness, strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.859-864
• /
• 2001

For earthquake resistance design, a response modification factor is used to reduce the design strength and it reflects ductility, reserve strength, redundancy and damping effect. But this factor has not theoretical basis. In this study, two response modification factors are compared and analyzed for shear wall apartment building.; the one is introduced by ATC-19 Procedures, the other is suggested FEMA-273 and ATC-40 through nonlinear static analysis. For the results, ATC-19 procedure gives a reasonable estimation to R factor. But $R_{u}$ by using FEAM-273 and ATC-40 methods is estimated so small in case of a minor or moderate earthquake region. Due to this fact, response modification factor is smaller than suggested load criterion 3.0. So, it needs to decrease wall volume and reduce the global strength and system stiffness for proper ductile behavior matching to domestic load criterion.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.203-208
• /
• 2002

In order to reduce the booming noise caused by first bending mode of a drive shaft, this paper proposes a simulation program for prediction of the bending mode frequency of any tubular shaft. This program consists of a pre-processor for modeling of geometrical shape of the drive shaft with boundary conditions of various joints, a processor for constructing of global finite element matrices using beam elements and an eigen-solver based on MATLAB program. Using this simulation program, the effective and accurate FE model far a shaft attached to vehicle can be obtained by aid of database for stiffness of each joint. Thus the resonance frequencies and mode shapes of a shaft can be calculated accurately. Because the effect of the resonance on interior noise can be verified, more improved shaft will be proposed at the early stage of design.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.83-90
• /
• 2004

Substructuring methods are usually used in finite element structural analyses. In this study a multi-level substructuring algorithm is developed and proposed as a possible candidate for incompressible fluid solves. Finite element formulation for incompressible flow has been stabilized by a modified residual procedure proposed by Ilinca et.al.[5]. The present algorithm consists of four stages such as a gathering stage, a condensing stage, a solving stage and a scattering stage. At each level, a predetermined number of elements are gathered and condensed to form an element of higher level. At highest level, each subdomain consists of only one super-element. Thus, the inversion process of a stiffness matrix associated with internal degrees of freedom of each subdomain has been replaced by a sequential static condensation. The global algebraic system arising feom the assembly of each subdomains is solved using Conjugate Gradient Squared(CGS) method. In this case, pre-conditioning techniques usually accompanied by iterative solvers are not needed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.826-831
• /
• 2002

In order to investigate the dynamic characteristics of real structure, many dynamic engineer had been interested in modal test however it is not easy to perform dynamic test of large structure because of many difficulties such as unsatisfied excitation force in global mode frequency range, measurement of dynamic force and so on. Therefore. new type vibration exciter with variable stiffness support system and dynamic force was developed to provide a improved experimental environment for a large and complex structure. The developed exciter improved from two viewpoint, dynamic performance and utility convenience. its characteristics was shown in this paper.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1201-1210
• /
• 2002

A penalty frame method is proposed for the coupled analysis of finite elements with independently modeled substructures. Although previously reported hybrid interface method by Aminpour et al (IJNME, Vol 38, 1995) is accurate and reliable, it requires non-conventional special solution algorithm such as multifrontal solver. In present study, an alternative method has been developed using penalty frame constraints, which results in positive symmetric global stiffness matrices. Thus the conventional skyline solver or band solver can be utilized in the solution routine, which makes the present method applicable in the environment of conventional finite element commercial software. Numerical examples show applicability of the present method.

• Structural Engineering and Mechanics
• /
• v.45 no.4
• /
• pp.521-542
• /
• 2013

In this study a truss model is used for the geometrically nonlinear static and dynamic analysis of a thin shallow arch subject to snap-through. Thanks to the very simple geometry of a truss, the equilibrium conditions can be easily written and the global stiffness matrix can be easily updated with respect to the deformed structure, within each step of the analysis. A very coarse discretization is applied; so, in a very simple way, the high frequency modes are suppressed from the beginning and there is no need to develop a complicated reduced-order technique. Two short computer programs have been developed for the geometrically nonlinear static analysis by displacement control of a plane truss model of a structure as well as for its dynamic analysis by the step-by-step time integration algorithm of trapezoidal rule, combined with a predictor-corrector technique. These two short, fully documented computer programs are applied on the geometrically nonlinear static and dynamic analysis of a specific thin shallow arch subject to snap-through.

• Structural Engineering and Mechanics
• /
• v.43 no.3
• /
• pp.273-285
• /
• 2012

Structural reanalysis is frequently used to reduce the computational cost during the process of design or optimization. The supports can be regarded as the design variables in various types of structural optimization problems. The location, number, and type of supports may be varied in order to yield a more effective design. The paper is focused on structural static reanalysis problem with added supports where some node displacements along axes of the global coordinate system are specified. A new approach is proposed and exact solutions can be provided by the approach. Thus, it belongs to the direct reanalysis methods. The information from the initial analysis has been fully exploited. Numerical examples show that the exact results can be achieved and the computational time can be significantly reduced by the proposed method.

• Earthquakes and Structures
• /
• v.6 no.1
• /
• pp.45-69
• /
• 2014

The 2009 L'Aquila, Italy earthquake shook a high density area causing a wide spectrum of damage to reinforced concrete with infill buildings, one of the most common building types used in Italy. The earthquake has proven to be a "full-scale" laboratory to further understand building performance. This paper presents the first results of a joint research effort between the University of Bologna and Degenkolb Engineers, aimed at investigating the seismic behavior of an infilled frame building that collapsed during the earthquake. State-of-the-practice techniques were implemented as a way to determine the reliability of these modeling techniques in anticipating the observed building performance. The main results indicate that: (i) the state-of-the-practice techniques are able to predict the observed behavior of the buildings; (ii) the masonry infills have a great influence on the behavior of the building in terms of stiffness, strength and global ductility.