• Journal of applied mathematics & informatics
• /
• v.35 no.1_2
• /
• pp.165-180
• /
• 2017

In this study, Taylor matrix algorithm is designed for the approximate solution of linear and non-linear differential equation systems. The algorithm is essentially based on the expansion of the functions in differential equation systems to Taylor series and substituting the matrix forms of these expansions into the given equation systems. Using the Mathematica program, the matrix equations are solved and the unknown Taylor coefficients are found approximately. The presented numerical approach is discussed on samples from various linear and non-linear differential equation systems as well as stiff systems. The computational data are then compared with those of some earlier numerical or exact results. As a result, this comparison demonstrates that the proposed method is accurate and reliable.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.04a
• /
• pp.228-233
• /
• 2005

Two-dimensional Stokes flows through a micro channel with a couple of symmetric vertical fins are investigated. At far up- and down-stream from the fins, the plane Poiseuille flow exists in the channel. The slip boundary conditions are applied to take account of the Knudsen number effects. For the analysis, the method of eigen function expansion and collocation method are employed. By the results, the streamline patterns and pressure distributions are shown and the force exerted on the fin and the excess pressure drop due to the fins are determined as functions of the length of the fin and Knudsen number. It may be conjectured that the force and the excess pressure drop are almost independent of the Knudsen number.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.871-879
• /
• 1998

The refrigerator consists of many components such as compressor condenser expansion valve evaporator and the cabinet which filled by urethane foam. In this paper the heat leakage of refriger-ator is measured by the new experiment method which is different from a present method, The devi-ation of the UA(overall heat transfer coefficient times area) between the simulation and experiments is about 7-8%. Using the modeling of various components of refrigeration system a performance analysos of CFC 12 and HFC 134a is performed numerically on the UA. As the results of this study according to increase the heat leakage the refrigeration load and mass flow rate of refrigerant are increased. And the increase of the mass flow rate results in the increase of the condensing and evapo-rating temperature. Therefore according to increase of the heat leakage the COP leads to increase because the increase of refrigeration capacity is larger than the increase if compressor power.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.826-833
• /
• 2010

Electric-thermal-structural actuated compliant mechanisms are mechanisms onto which electric voltage drop is applied as input instead of force. This mechanism is based on thermal expansion of material while being heated. Compliant mechanisms are designed subjected to electric charge input using BESO(bi-directional evolutionary structural optimization) method. Reliability-based topology optimization (RBTO) is applied to the topology design of actuators. performance measure approach (PMA), which has probabilistic constraints that are formulated in terms of the reliability index, is adopted to evaluate the probabilistic constraints. In this study, BESO method is used to obtain optimal topology of compliant mechanisms from initial design domain. PMA approach is used to evaluate reliability index. The procedure has been tested in numerical applications and compared with the results obtained by other methods to validate these approaches.

• Proceedings of the Korea Contents Association Conference
• /
• 2004.05a
• /
• pp.278-282
• /
• 2004

Recently traffic flooding attack has happened faster and faster owing to expansion of the worm attack and development of the method of traffic flooding attack. The method in the past time is problematic in detecting the recent traffic flooding attacks, which are running quickly. Therefore, this paper aims to establish the algorithm which reduces the time of detection to traffic flooding attack in collecting and analyzing traffics.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.122-125
• /
• 2003

An adaptive contour smoothing algorithm designed as a preprocessor for shape coders is presented. In the proposed method, the degree of the adaptive smoothing is controlled based on the significance of each contour point, which is quantified according to inter-region contrast in an intensity image. The actual smoothing consists of an expansion operator and a thinning algorithm. Experimental results show that the proposed method results in a saving of about 20% in number of coded bits with a negligible additional texture degradation in the reconstructed intensity image.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.515-523
• /
• 2003

Shape memory is physical phenomenon which a platically metal is restored to its original shape by a solid state phase change by heating. TiNi alloy the most effective material in the shape memory alloy(SMA). To study(measure) recovery stress of intelligent composite. Ti50-Ni50 shape memory matrix with prestrain SMA fiber. When SMA fiber of the intelligent composite is heated over austenite starting temperature(As) by electric heating. a recovery stress are generated. The recovery stress of the intelligent composite was measured by strain gage or photoelastic experiment. Measuring method of recovery stress by photoelastic experiment was developed in this research. It was certified that photoelastic experiment was more effective and more precise than strain gage method in the measurement of recovery stress.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.987-993
• /
• 2003

The module UPS can flexibly implement expansion of power system capacities. Furthermore, it can be used to build up the parallel redundant system to improve the reliability of power system operation. To realize the module UPS, load sharing without interconnection among parallel connecting modules as well as a small scale and lightweight topology is necessary. In this paper, the three-arm converter/inverter is compared with the general full-bridge and half-bridge topology from a practical point of view and chosen as the module UPS topology. The switching control approaches based on a pulse width modulation of the converter and inverter of the system are presented independently The frequency and voltage droop method is applied to parallel operation control to achieve load sharing. Two prototype 3kVA modules are designed and implemented to confirm the effectiveness of the proposed approaches. Experimental results show that the three-arm UPS system has a high power factor, a low distortion of output voltage and input current, and good load sharing characteristic.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.129-130
• /
• 2017

By comparing the survey and the actual situation at hand, the results showed that the lowest floor slab, wall construction joints, and floor expansion joints were the most prone to leakage. A waterproofing design method in underground parts of apartments is proposed to prevent leakage in underground of apartments. Further research is required for the establishment of this detailed design and construction guideline in regards to this study.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.378-383
• /
• 2005

The performances of side channel type regenerative blowers were evaluated by the blower performance test, 1-D performance prediction and CFD. The performance prediction method was modified using the results of the performance test and CFD and applied to the design of the new regenerative blowers. The major geometric parameters such as channel height, channel area and expansion angle were decided from the performance prediction method for the improved models and the predicted results were compared with CFD and experimental data. Both of the modified models showed improved efficiency at the operating condition. Especially, model3 could be possible to reduce operating rotating speed, that is benefit to noise performance, because of the high head performance at the design point. The CFD results showed that the performance of the regenerative blower was influenced by the secondary circulatory flow in the channel.