• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.1
• /
• pp.1-9
• /
• 2002

This paper describes for new design method to improve respones characteristics of moving-magnet type LDM with volume reduction of slider back iron. To achieve the constant thrust of LDM through restraining saturation at the center core of stator excitation coil, double sided stator winding of LDM is proposed. We constructed new type LDM to prove the validity of design process. Analysis results through measurement and simulation of proposed multi-separated winding LDM were proved excellent in response characteristics and static thrust.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.370-375
• /
• 2011

In this paper, we propose an antenna module with high isolation between Tx and Rx in RFID reader module. The proposed module consists of a quadrafilar antenna and a directional coupler with a switchable dummy load to improve the directivity. The proposed module achieves the isolation higher than 20 dB between Tx and Rx. To show the validity of the proposed scheme, we have performed the measurement of tagging range and multi-tagging ability. The experiment results show that the detecting range and multi-tagging ability are enhanced by 81% and 200%, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.208-211
• /
• 2000

We prepared Co-Cr-Ta and Co-Cr-Ta/Ti thin film for perpendicular magnetic recording media by facing targets sputtering system (FTS system). Ti underlayer effects on crystallographic and magnetic characteristics of Co-Cr-Ta perpendicular magnetic recording media have been investigated. Crystallgraphic and magnetic characteristic of prepared thin films were evaluated by x-ray diffractometry(XRD), vibrating sample magnetometer(VSM) and kerr hysteresis loop measurement. The coercivity and anisotropy field increase by introduced Ti underlayer when substrate temperature is higher than 150$^{\circ}C$. The c-axis dispersion angle and grain size of Co-Cr-Ta/Ti thin film is decrease than Co-Cr-Ta when substrate temperature is higher than 100$^{\circ}C$. Consequently, the use of a Ti underlayer highly orientated can be improved crystallographic and magnetic characteristics of Co-Cr -Ta perpendicular media layer.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.2
• /
• pp.330-337
• /
• 2018

This paper proposes a technique to analyze the flatness characteristics of the attenuator at 10Hz to $50\text\tiny{MHz}$ on the basis of $1\text\tiny{kHz}$ using a Thermal Voltage Converter and AC measurement standard. In the proposed technique, the input voltage of the attenuator for each measuring frequency is supplied at the same rate as $1\text\tiny{kHz}$ using TVC, and the flatness characteristics of the attenuator are analyzed by the voltage variation indicated in the AC measurement standard. The results of the analysis of the attenuator flatness characteristics show that the maximum uncertainty of $866{\mu}V/V$ can be measured from $10\text\tiny{dB}$ to $70\text\tiny{dB}$ and the uncertainty is reduced by about 37% compared to $2.31\text\tiny{mV}$/V using the network measurement method. The improved attenuator flatness characteristic values can be applied to the frequency flatness calibration from 2.2V to 2.2mV at the low voltage of the AC measurement standard.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.1
• /
• pp.70-78
• /
• 2000

In applying high-${\underline{T_c}}$ superconducting material to microwave devices, Uncertainty of electromagnetics of high-${\underline{T_c}}$ superconductor(HTS) and the temperature dependence of the substrate fits with HTS thin film cause difficulty in realization of such antenna for industrial applications. It must be noted to characteristic the HTS antenna in contrast with normal conducting counterpart for this real application. In this paper, a comparative study between HTS microstrip antennas and gold antennas was reported in terms of the return loss, the characteristic impedance, efficiency, and other various characteristics. HTS thin films were $YBa_2Cu_3O_{7-x}$ (YBCO) on MgO substrates. Superconducting microstrip antennas used in this work were to directly inset a microstrip transmission line into the 50 ${\Omega}$ region of the radiating patch. Measurement results of HTS antennas and gold antennas showed that usable antennas can be made using this architecture.

• Journal of IKEEE
• /
• v.28 no.1
• /
• pp.104-109
• /
• 2024

In this research, we explored the influence of post-annealing atmospheres on the electrical properties of Ga₂O₃/SiC heterojunction diodes. We fabricated Ga₂O₃/SiC heterojunction diodes by RF sputtering and after the fabrication the post-annealing in various gas atmospheres was performed. We measured the changes in deep-level defects using Deep Level Transient Spectroscopy (DLTS) and we conducted an electrical characteristic of J-V measurement and Hall measurement to analyzed the effects of annealing atmosphere on Ga₂O₃/SiC heterojunction diode. In the N₂ annealed devices, the highest on-state current was measured as 3.06 × 10^-2 A/cm^2, and an increase in carrier concentration of 3.8 × 10¹⁴ cm^-3 was observed. This confirms that the variations in deep level defects due to the post-annealing atmosphere can influence the electrical properties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.11
• /
• pp.740-744
• /
• 2017

Herein we studied the electrical and optical properties of indium tin oxide ITO/Ag/ITO multilayer thin films for application in transparent conducting electrodes. The ITO and Ag thin films were deposited onto soda lime glass (SLG) using radiofrequency and DC-sputtering methods, respectively. The as-synthesized ITO/Ag/ITO multilayer thin films were analyzed using 4-point probe, UV-Visible spectroscopy, and Hall measurement. We observed a rapid increase in electron concentration with increasing Ag thickness. However, electron mobility decreased with increasing Ag thickness. Finally, ITO/Ag/ITO multilayer thin films showed a characteristic low sheet resistance of $18{\Omega}/sq$ and high optical transmittance value (80%) with variation of Ag thickness (5~10 nm).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.2
• /
• pp.119-125
• /
• 2013

In this paper, semiconducting shield specimens for a DC cable is fabricated and characterized by measurement of volume resistance, tensile strength, and the coefficient of expansion to show the electrical and mechanical characteristics of the semiconducting shield. Due to the PTC phenomenon, the volume resistance at $25^{\circ}C$ increases rapidly in comparison to the volume resistance at $90^{\circ}C$. Since the compounding ratio of carbon black is low, the tensile strength and density become lower and the coefficient of expansion is increased. As the general specification of the tensile strength and density is $0.8kgf/mm^2$ and 150%, respectively, the fabricated specimen in this paper has excellent mechanical characteristic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.47-47
• /
• 2009

The formation of variable one-dimensional structures including core/shell structure is of particular significance with respect to potential applications for thermoelectric devices with the enhanced figure of merit ($ZT=S2{\sigma}T/{\kappa}$). We report the fabrication of Bi-Te core/shell nanowire based on a novel stress induced method. Fig. 1 schematically shows the nanowire fabrication process. Bi nanowires are grown on the Si substrate by the stress-induced method, and then Te is evaporated on the Bi nanowires. Fig. 2 is a transmission electron microscopy image clearly showing a core/shell structure for which effective phonon scattering and quantum confinement effect are expected. Electrical conductivity of the core/shell nanowire was measured at the temperatures from 4K to 300K, respectively. Our results demonstrate that Bi-Te core/shell nanowire can be grown successfully by the stress-induced method. Based on the result of electrical transport measurement and characteristic morphology of rough surface, Seebeck coefficient and thermal conductivity of Bi-Te core/shell nanowires are presented.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.11
• /
• pp.1669-1674
• /
• 2017

In this study, We have discussed the development of a diagnostic device to detect and prevent electrical fire due to the arc caused by contact failure and partial disconnection at the connection part of the three-phase electric heater wiring used in the industrial field. The arc caused by contact failure and partial disconnection at the connection part of the electric heater shows a change in the current effective value. Therefore, it is possible to determine whether there exists a defect by analyzing the current unbalance factor and the number of current fluctuations with the diagnostic apparatus. The three-phase unbalanced heater is considered to be capable of determining defects through periodic measurement and trend analysis of the current unbalance factor. It is also expected that this device can be used not only for electric heaters but also for detection of defects in wiring and connections of electrical equipment having a characteristic of constant load current.