• Restorative Dentistry and Endodontics
• /
• v.25 no.2
• /
• pp.202-211
• /
• 2000

The aim of this study was to compare the apical sealing ability of a new thermoplasticized gutta-percha filling technique, the Easy Filling and the Quick Obturation system with lateral condensation technique and Thermafil system to evaluate their clinical acceptabilities. Fifty-two extracted single-rooted teeth were instrumented to #35 using the .04 taper ProFile system. Four groups of 12 teeth were obturated by lateral condensation technique. Thermafil system and two new thermoplasticized gutta-percha techniques, the Easy Filling system and Quick Obturation system (Meta Dental co. Ltd. Korea), respectively. Four teeth served as controls. After the teeth were immersed in 2% methylene blue dye for 48 hours, they were resected horizontally at 1mm to 5mm level from the anatomical apex using a low-speed microtome. Each section was examined under a stereomicroscope at ${\times40}$ magnification and photographed. After each image was scanned, the leakage area was measured at each level using Brain 3 (Nosdia Tech., Korea) software. Leakage ratio was calculated for each group and was analyzed statistically to come up with the following results: 1. At 1mm level, the Quick Obturation system had the largest amount of apical leakage and it was statistically significant when compared with the lateral condensation group and the Thermafil group (p<0.05). 2. At 2mm and 3mm level, there were no significant difference of apical leakage among all four groups (p>0.05), and from 4mm level, no apical dye penetration was observed in all the groups. In conclusion, the apical seal produced by Easy Filling system and the Quick Obturation system was comparable to lateral condensation technique and Thermafil system except for the 1mm level. More improvement of the apical seal can be expected as the operator becomes skillful with the new techniques.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.10a
• /
• pp.112-120
• /
• 1992

The use of Pre-processor for building structural analysis used to rely upon filling up fixed format data, which was ineffective and error-prone. This research attempts to integrate structural analysis system with DBMS and CAD system in order to make it easy to exchange data between pre-process, analysis, and post-process stages. Automatic generation of database from pre-process stage allows easy preparation of main input data for other structural analysis programs. CAD system with some sub-programs written in LISP and C works as a graphic user interface. This approach gives an easy, effective and error-free way of inputing data for structural analysis.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.506-507
• /
• 1992

When it comes to the 'Leak Detector System' generally, our country has a large income 'Rotary Type Leak Detector' of foreign goods. The completed development of the 'Line Type Leak-Detector' system was produced to check Whether the containers for small and large on the filling line are auto defective. This system is applied to the filling package Processing during the production and contributed to inproving competiveness of domestic containers manufactures of all society of Industry. Also, high precision and realiablity, very compact size, low cost and Easy set-up etc. by checking the experimental data directly plan, Design and making for '1 Compression Head Control Leak Detector System'. This flexcible system can be equipped with multiple Compression heads depending on the requested prodution test rate and test precision.

• The Journal of the Korean dental association
• /
• v.56 no.10
• /
• pp.567-571
• /
• 2018

Obturation is a important procedure of root canal treatment. Canal filling should be both provide a hermetic seal for the root canal system and eliminate leakage channel from the oral cavity. Gutta-percha have been the standard material of choice for root canal obturation. Canal filling has been aimed at maximizing the amount of gutta-percha and minimizing the amount of sealer. However recently, single cone technique has been introduced that include calcium silicate-based sealer and single gutta-percha cone. It is important to select an obturation technique that offers consistency and is easy to use. From the standpoint of appropriate technology, the single cone technique is thought to be useful for general dentist.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1383-1388
• /
• 2015

Proportional integral derivative (PID) control is one of the conventional control strategies. Industrial PID control has many options, tools, and parameters for dealing with the wide spectrum of difficulties and opportunities in manufacturing plants. It has a simple control structure that is easy to understand and relatively easy to tune. Injection mold is warming up to the idea of cycling the tool surface temperature during the molding cycle rather than keeping it constant. This “heating and cooling” process has rapidly gained popularity abroad. However, it has discovered that raising the mold wall temperature above the resin’s glass-transition or crystalline melting temperature during the filling stage is followed by rapid cooling and improved product performance in applications from automotive to packaging to optics. In previous studies, optimization methods were mainly selected on the basis of the subjective experience. Appropriate techniques are necessary to optimize the cooling channels for the injection mold. In this study, a digital signal processor (DSP)-based PID control system is applied to injection molding machines. The main aim of this study is to optimize the control of the proposed structure, including a digital PID control method with a DSP chip in the injection molding machine.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.267-268
• /
• 2018

The purpose of this study was to analyze the thermal performance of a cladding system which developed for easy maintenance and flexibility and installed on a long-life housing. The developed cladding systems were finished mock-up test at an authorized certification laboratory and were satisfied with the standard of the external wall system. The surface temperature and linear thermal transmittance of the cladding system were investigated by using the THERM as a simulation program. The joining part between the cladding systems had a weakness of condensation resistance. The surface temperature of the joining part was improved by filling and adding insulation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.188-188
• /
• 2011

Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Meta Oxide Semiconductor) based electronic devices, the electronic devices, become much faster and smaller size that are promising property of semiconductor market. However, very narrow interconnect line width has some disadvantages. Deposition of conformal and thin barrier is not easy. And metallization process needs deposition of diffusion barrier and glue layer for EP/ELP deposition. Thus, there is not enough space for copper filling process. In order to get over these negative effects, simple process of copper metallization is important. In this study, Cu-V alloy layer was deposited using of DC/RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane SiO2/Si bi-layer substrate with smooth surface. Cu-V film's thickness was about 50 nm. Cu-V alloy film deposited at $150^{\circ}C$. XRD, AFM, Hall measurement system, and AES were used to analyze this work. For the barrier formation, annealing temperature was 300, 400, $500^{\circ}C$ (1 hour). Barrier thermal stability was tested by I-V(leakage current) and XRD analysis after 300, 500, $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However vanadium-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Therefore thermal stability of vanadium-based diffusion barrier is desirable for copper interconnection.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.1
• /
• pp.11-17
• /
• 2005

This study was performed to analysis the operation process when fabric pattern design was done by the use of CAD system compared with the manual work in order to determine the operation efficiency with the application of fabric design CAD system. The results of the study were as follows: 1. since 160,000 colors were supported by CAD system, color proposed by consumer was able to match exactly according to the its design. However, exact color matching was not possible by manual work. 2. Woven state of back of pattern design could be identified simultaneously with face of it for CAD system, while face and back of the fabrics should be designed separatedly in case of manual work. 3. Since the combination of warp and filling yarn was compatible with the fabric density in one repeat unit in CAD system, exact size of pattern design to be woven was able to expressed. 4. Only simple graphical expression by manual work was seen, while with the CAD system, texture and shade effect as well as graphical expression could be expressed and so fault could be reduced in advance with the simulation of actual feeling of fabrics in the screen. In conclusion, when CAD system will be introduced to the textile industry, operation time of designing pattern can be reduced. Since the operation is easy and simple, a beginner can operate CAD system easily. Thus, production and wage costs can be saved and this can be related directly with the improvement of productivity which is the main purpose of introducing CAD system.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3128-3132
• /
• 2010

A disposable solid-state pH sensor was realized by utilizing two nanoporous Pt (npPt) electrodes and a copolyelectrolytic junction. One nanoporous Pt electrode was to measure the pH as an indicating electrode (pH-IE) and the other assembled with copolyelectrolytic junction was to maintain constant open circuit potential ($E_{oc}$) as a solid-state reference electrode (SSRE). The copolyelectrolytic junction was composed of cationic and anionic polymers immobilized by photo-polymerization of N,N'-methylenebisacrylamide, making buffered electrolytic environment on the SSRE. It was expected to make. The nanoporous Pt surrounded by a constant pH excellently worked as a solid state reference electrode so as to stabilize the system within 30 s and retain the electrochemical environment regardless of unknown sample solutions. Combination between the SSRE and the pH-IE commonly based on nanoporous Pt yielded a complete solid-state pH sensor that requires no internal filling solution. The solid state pH sensing chip is simple and easy to fabricate so that it could be practically used for disposable purposes. Moreover, the solid-state pH sensor successfully functions in calibration-free mode in a variety of buffers and surfactant samples.

• East Asian Journal of Business Economics (EAJBE)
• /
• v.11 no.4
• /
• pp.11-18
• /
• 2023

Purpose - By filling the existing research hole and supplying a whole evaluation, this test wants to offer actionable insights for stakeholders navigating the intersection of sustainability and financial prosperity. Ultimately, this study contributes to the evolving speak on ESG, fostering a deeper comprehension of its implications for fostering sustainable economic increase. Research design, data, and methodology - Based on the numerous prior literature, the current study adopts a rigorous and systematic approach to discover the connection between Environmental, Social, and Governance (ESG) performance and its effect on a financial boom. The Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) method is the guiding framework for systematically accumulating and analyzing earlier research studies. Result: The finding of this study indicates that using ESG-pushed innovation, practitioners can force technological advancements inside their respective industries. By combining sustainability with research and improvement tasks, corporations can be leaders in selling economic boom through current, green solutions. Conclusion - In summary, this study concludes that embracing those findings in this study allows practitioners and managers to enhance their organization's easy regular, well-known traditional regular standard overall performance and undoubtedly contribute to a broader financial boom via leveraging the transformative strength of ESG necessities.