• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.2
• /
• pp.87-89
• /
• 2006

This paper proposes a sense amplifier with non-volatile memory in order to improve the image quality of LCD by enhancing the matching of the driving voltages between the panel and driver. The sense amplifier having a wide sensing margin and fast response adjusts LCD driver voltage of display driver. The CSTN-LCD with the sense amplifier results improved image quality than that with conventional 6 bit column driver without it.

• Journal of Biomedical Engineering Research
• /
• v.16 no.3
• /
• pp.301-308
• /
• 1995

A high-precision pre-amplifier is designed for general use in EEG measurement system. It consists of signal generator, signal amplifier with a impedance converter, shield driver, body driver, differential amplifier, and isolation amplifier. The combination of minimum use of inaccurate passive components and the appropriate matching of each monolithic amplifiers results in good noise behavior, low leakage current, high CMRR, high input impedance, and high IMRR. The performance of EEG pre-amplifier has been verified by showing the typical EEG pattevn of a nomad person through the clinical experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.3A
• /
• pp.356-359
• /
• 2006

A monolithic SiGe HBT variable gain driver amplifier(VGDA) with high dB-linear gain control and high linearity has been developed as a driver amplifier with ground-shielded microstrip lines for 5-GHz transmitters. The VGDA consists of three blocks such as the cascode gain-control stage, fixed-gain output stage, and voltage control block. The circuit elements were optimized by using the Agilent Technologies' ADSs. The VGDA was implemented in STMicroelectronics' 0.35${\mu}m$ Si-BiCMOS process. The VGDA exhibits a dynamic gain control range of 34 dB with the control voltage range from 0 to 2.3 V in 5.15-5.35 GHz band. At 5.15 GHz, maximum gain and attenuation are 10.5 dB and -23.6 dB, respectively. The amplifier also produces a 1-dB gain-compression output power of -3 dBm and output third-order intercept point of 7.5 dBm. Input/output voltage standing wave ratios of the VGDA keep low and constant despite change in the gain-control voltage.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.247-253
• /
• 2009

We propose a Ku-band driver and high-power amplifier monolithic microwave integrated circuits (MMICs) employing a compensating gate bias circuit using a commercial 0.5 ${\mu}m$ GaAs pHEMT technology. The integrated gate bias circuit provides compensation for the threshold voltage and temperature variations as well as independence of the supply voltage variations. A fabricated two-stage Ku-band driver amplifier MMIC exhibits a typical output power of 30.5 dBm and power-added efficiency (PAE) of 37% over a 13.5 GHz to 15.0 GHz frequency band, while a fabricated three-stage Ku-band high-power amplifier MMIC exhibits a maximum saturated output power of 39.25 dBm (8.4 W) and PAE of 22.7% at 14.5 GHz.

• Proceedings of the KOSOMBE Conference
• /
• v.1995 no.05
• /
• pp.68-70
• /
• 1995

A low-noise pre-amplifier is developed for use in Topographic Brain Mapping system. It consists of signal generator, signal amplifier with a impedance converter, shield driver, body driver, differential amplifier, and isolation amplifier. Pre-amplifier circuit is designed with the concept of isolation and active body and shield driver. This amplifier shows the good noise behavior, high CMRR, high input impedance, low leakage current and high IMRR.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.2
• /
• pp.56-62
• /
• 2002

A new high speed and low voltage swing on-chip BUS using threshold voltage swing driver and dual sense amplifier receiver is proposed. The threshold voltage swing driver reduces the rising time in the bus to 30% of the full CMOS inverter driver and the dual sense amplifier receiver increases twice the throughput. of the conventional reduced-swing buses using sense amplifier receiver. With threshold voltage swing driver and dual sense amplifier receiver combined, approximately 60% speed improvement and 75% power reduction are achieved in the proposed scheme compared to the conventional full CMOS inverter for the on-chip bus.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.3
• /
• pp.52-59
• /
• 1997

Design and performance of principal four ICs for the 10-Gb/s optical communication system are presented. AlGaAs/GaAs HBTs are basic devices to implement a laser diode driver, apre-amplifier, and a limiting amplifier, and GaInP/GaAs HBTs are used for an AGC amplifier. We fbricated 11.5-GHz LD driver, a pre-amplifier, and a limiting amplifier, an dGaInP/GaAs HBTs are used for an AGC amplifier. We fabricated LD deriver, 10.5 GHz pre amplifier, 7.2 GHz AGC amplifier, and 10.3 GHz limiting amplifier, optimized circuit design and the stabilized MMIC fabrication process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.423-424
• /
• 2011

This paper has proposed a 920 MHz RF front-end for IEEE 802.15.4g SUN (Smart Utility Network) systems. The proposed 920 MHz RF front-end consists of a driver amplifier, a low noise amplifier, and a RF switch. In the TX mode, the driver amplifier has been designed as a single-ended topology to remove a transformer which causes a loss of the output power from the driver amplifier. In addition, a RF switch is located in the RX path not the TX path. In the RX mode, the proposed low noise amplifier can provide a differential output signal when a single-ended input signal has been applied to. A LC resonant circuit is used as both a load of the drive amplifier and a input matching circuit of the low noise amplifier, reducing the chip area. The proposed 920 MHz RF Front-end has been implemented in a 0.18-um CMOS technology. It consumes 3.6 mA in driver amplifier and 3.1 mA in low noise amplifier from a 1.8 V supply voltage.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.07a
• /
• pp.340-340
• /
• 2004

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1030-1039
• /
• 2006

A high power and high gain Doherty amplifier is designed by using embedded driver amplifiers in the final stage. The operational characteristics of a two-stage Doherty amplifier are analyzed, as a function of the two-stage peaking amplifier gate biases. The driver stages and final output stages are implemented using two single-ended MRF21045s and a single push-pull packaged MRF5P21180, respectively. This two-stage Doherty amplifier demonstrated 27 dB gain with a PAE of 23 % at 15 W average output power.