• The Journal of the Korea Contents Association
• /
• v.10 no.12
• /
• pp.10-17
• /
• 2010

In this paper, we design digital D-PHY link chip controling DSI (Display Serial Interface) that meets MIPI (Mobile Industry Processor Interface) standard. The D-PHY supports a high-speed (HS) mode for fast data traffic and a low-power (LP) mode for control transactions. For low power consumption, the unit blocks in digital D-PHY are optionally switched using the clock gating technique. The proposed low power digital D-PHY is simulated and compared with conven tional one about power consumption on each transaction mode. As a result, power consumptions of TX, RX, and total in HS mode decrease 74%, 31%, and 50%, respectively. In LP mode, power reduction rates of TX, RX, and total are 79%, 40%, and 51.5%, separately. We implemented the low power MIPI D-PHY digital chip using $0.13-{\mu}m$ CMOS process under 1.2V supply.

• Journal of Advanced Navigation Technology
• /
• v.13 no.1
• /
• pp.48-53
• /
• 2009

The CMOS RF front-end for Global Positioning System(GPS)are implemented in 1P8M CMOS $0.13{\mu}m$ process. The LNAs consist of LNA1 with high gain and low NF, and LNA2 with low gain and high IIP3 for supporting operation with active and passive antenna. the measured performances of both LNAs are 16.4/13.8 dB gain, 1.4/1.68 dB NF, and -8/-4.4 dBm IIP3 with 3.2/2 mA form 1.2 V supply, respectively. The quadrature downconversion mixer is followed by transimpedance amplifier with gain controllability from 27.5 to 41 dB. The front-end performances in LNA1 mode are 39.8 dB conversion gain, 2.2 dB NF, and -33.4 dBm IIP3 with 6.6 mW power consumption.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.6
• /
• pp.802-809
• /
• 2014

This paper presents a dual-mode bias modulator (BM) for complementary metal oxide semiconductor (CMOS) power amplifiers (PAs). The BM includes a hybrid buck converter and a normal buck converter for an envelope tracking (ET) mode for high output power and for an average power tracking (APT) mode for low output power, respectively. The dual-mode BM and CMOS PA are designed using a $0.18-{\mu}m$ CMOS process for the 1.75 GHz band. For the 16-QAM LTE signal with a peak-to-average power ratio of 7.3 dB and a bandwidth of 5 MHz, the PA with the ET mode exhibited a poweradded efficiency (PAE) of 39.2%, an EVM of 4.8%, a gain of 19.0 dB, and an adjacent channel leakage power ratio of -30 dBc at an average output power of 22 dBm, while the stand-alone PA has a PAE of 8% lower at the same condition. The PA with APT mode has a PAE of 21.3%, which is an improvement of 13.4% from that of the stand-alone PA at an output power of 13 dBm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.73-76
• /
• 1997

A low loss x-cut LiNbO$_3$ optical waveguide was fabricated by Ti in-diffusion and the guided-mode properties and total insertion loss of pigtailing with polarization maintaining fiber(PMF) were investigated and measured at optical wavelength 15507. For formaing the waveguide, the parameters of diffusion Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set 1400$\AA$, 8${\mu}{\textrm}{m}$, 3.3cm, 105$0^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. and then After the polishing and pigtailing, it showed that total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, horizontal/vertical sizes were 13.87/18${\mu}{\textrm}{m}$ for TM mode, 9.61${\mu}{\textrm}{m}$/6.5${\mu}{\textrm}{m}$ for TE mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1060-1068
• /
• 2011

In this paper, Current-Mode Class-D(CMCD) RF Power Amplifier(PA) is designed and implemented at 900 MHz. Conventional CMCD PA has output parallel resonator to reconstruct a fundamental frequency component of the output signal. However the resonator can be removed by connecting inverse class-F PAs because even-harmonic components can be removed by CMCD PA's push-pull structure. Using load-pull, inverse class-F PA with GaN transistors is designed, and CMCD PA with the inverse class-F PA is implemented. The CMCD PA has 64.5 % drain efficiency, 34.2 dBm output power. Comparing with the drain efficiency of a CMCD PA with parallel resonator, the CMCD with the inverse class-F technology has 13.6 % improved drain efficiency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.7A
• /
• pp.712-718
• /
• 2004

We report 1.6 Tb/s (160${\times}$10 Gb/s) WDM transmission over 2,000 km of single mode fiber using distributed hybrid(distributed Raman amplifier＋Erbium-doped fiber amplifier) optical amplifiers. After transmission over 2,000 km of single mode fiber, average optical signal to noise ratios of C/L-band were 20.5 dB, 21.9 dB, respectively. The minimum Q-factors of each band were 14.65 dB (BER=5.8e-8) in C-band, 13.75 dB (BER=5.0e-7) in L-band without forward error correction. We performed 1.6 Tb/s error-free transmission over 2,000 km of single mode fiber using Reed-Solomon (255, 239) forward error correction code.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.96-99
• /
• 2008

This paper describes a $0.13-{\mu}m$ CMOS RF switch for $3{\sim}5$ GHz UWB band(mode 1). It can improve isolation characteristics between ports by using deep n-well RF devices while their source and body terminals are separated. From the measurement results, the proposed T/R switch is comparative to the on-wafer probing measurement results of the series-shunt T/R switches. When the proposed T/R switch operates as Tx mode, measured insertion loss from Tx to output port is less than 1.5 dB and isolation between Tx and Rx is more than 27 dB for $3{\sim}5$ GHz. Return loss for the Tx port is more than -10 dB and input P1dB is +10 dBm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.557-564
• /
• 1998

A low loss x-cut $LiNbO_3$optical waveguide was fabricated by Yi in-diffusion, and the properties of guided-mode and the total insertion loss of the pigtailed waveguide with polarization maintaining fiber(PMF) were measured at optical wavelength 1550nm. for forming the waveguides, the parameters of diffusion, Ti thickness, waveguide line-width, length, diffusion temperature, time and atmosphere were set $1400{\AA}$, $8{\mu}m$, 3.3cm, $1050^{\circ}C$, 8 hours and wet bubbled oxygen, respectively. And then after the polishing and piatailing, it showed that the total insertion loss was -4.1dB for TM mode, -5.5dB for TE mode, and mode size, that is, the horizontal/ vertical size were $13.8{\mu}m/18{\mu}m$ for TM mode, $9.6{\mu}m/6.5{\mu}m$ for TE mode.

• Journal of Advanced Navigation Technology
• /
• v.13 no.3
• /
• pp.337-343
• /
• 2009

In this paper, we proposed a burst mode symbol timing recovery unit that is applicable to the VDL Mode-2 using D8PSK modulation. A method that IIR loop filter is used to minimize symbol timing error is hard to apply to burst mode because its convergence time is long. That is, the fast convergence property is important. In this paper, the proposed method takes one sample which has maximum symbol power after the initial synchronization has been achieved by using preambles. The main principle of operation is that the unit moves one sample clock to advance or retard according to symbol power. We verify that the proposed method is operated well in ${\pm}100$ ppm or greater through the test results between Australia ADS Corp. transmitter and the designed receiver.

• Korean Journal of Optics and Photonics
• /
• v.10 no.1
• /
• pp.58-63
• /
• 1999

A 10 GHz harmonically mode-locked semiconductor-fiber ring laser was implemented using a semiconductor optical amplifier at $1.5\mu\textrm{m}$ The laser pulse has 13~18 ps pulse duration, 0.4~0.6 nm spectral width and was positively chirped. The output pulse with an average power of 4 dBm was compressed to 6.8 ps using 2 km long standard single mode optical fiber.