• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.3
• /
• pp.193-199
• /
• 2008

A combined clock and data recovery (CDR) circuit with adaptive cancellation of data-dependent jitter (DDJ) is constructed in all-digital architecture which is amenable to deep submicron technology. The DDJ canceller uses an adaptive FIR filter to compen-sate for any unknown channel characteristic. The proposed CDR decreases jitter in the recovered clock since the DDJ canceller significantly cancels out incoming jitter caused by inter-symbol interference.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.1
• /
• pp.68-75
• /
• 2009

In this paper, an efficient proposed CDR(Clock and Data Recovery Circuits) using 1/4-rate clock based on dual-interpolator is proposed. The CDR is aimed to overcome problems that using multi-phase clock to decrease the clock generator frequency causes side effects such as the increased power dissipation and hardware complexity, especially when the number of channels is high. To solve these problems, each recovery part generates needed additional clocks using only inverters, but not flip-flops while maintaining the number of clocks supplied from a clock generator the same as 1/2-rate clock method. Thus, the reduction of a clock generator frequency using 1/4-rate clocking helps relax the speed limitation and power dissipation when higher data rate transfer is demanded.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.12
• /
• pp.1644-1651
• /
• 1995

A data and clock recovery integrated circuit for MAC (Multiplexed Analog Component) TV standard is described. The chip performs the recovery of a system clock from a digitally encoded voice signal, clamping of a video signal for DC-level restoration, and precise gain control of a video signal in the presence of a large amplitude variation. A PLL (Phase Locked Loop) is used for timing recovery and a new gain control circuit is proposed which enhances its accuracy and dynamic range by employing two identical four-quadrant analog multipliers. The chip is designed in full custom with 1.5um BiCMOS technology, and layout verification is completed by post-simulation with the extracted circuit.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.4
• /
• pp.568-576
• /
• 2017

This paper presents a clock and data recovery circuit with an adaptive loop bandwidth calibration scheme and the idle power saved frequency acquisition. The loop bandwidth calibration adaptively controls injection currents of the main loop with a trimmable bandgap reference circuit and trains the VCO to operate in the linear frequency control range. For stand-by power reduction of the phase detector, a clock gating circuit blocks 8-phase clock signals from the VCO and cuts off the current paths of current mode D-flip flops and latches during the frequency acquisition. 77.96% reduction has been accomplished in idle power consumption of the phase detector. In the jitter experiment, the proposed scheme reduces the jitter tolerance variation from 0.45-UI to 0.2-UI at 1-MHz as compared with the conventional circuit.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.57-63
• /
• 2009

In this Paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuit is composed of CDR(Clock and Data Recovery) block and PLL(Phase Locked Loop) block. Lock dynamics is accomplished on the first data transition and data are sampled in the optimal point. The CDR circuit is realized in 0.35um CMOS process technology. With input pseudo-random bit sequences(PRBS) of $2^7-1$, the simulations show 17ps peak-to-peak retimed data jitter characteristics. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.324-328
• /
• 2012

A recovered jitter of CDR(Clock and Data Recovery) Circuit based on Dual-loop DLL(Delay Locked Loop) for data recovery in high speed serial data communication is changed by depending on the input data and reference clock frequency. In this paper, 2-step DPC which has constant jitter performance for wide-range input frequency is proposed. The designed prototype 2-step CDR using proposed 2-step DPC has operation frequency between 200Mbps and 4Gbps. Average delay step of 2-step DPC is 10ps. Designed CDR circuit was tested with 0.18um CMOS process.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.40-46
• /
• 2010

This paper describes a clock and data recovery (CDR) circuit that supports dual data rates of 2.7Gbps and 1.62Gbps for DisplayPort standard. The proposed CDR has a dual mode voltage-controlled oscillator (VCO) that changes the operating frequency with a "Mode" switch control. The chip has been implemented using $0.18{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of 37ps(@2.7Gbps) and 27ps(@1.62Gbps) in the recovered data. The power dissipation is 80mW at 2.7Gbps rate from a 1.8V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.8A
• /
• pp.644-649
• /
• 2003

Novel 622Mb/s burst-mode clock and data recovery (CDR) circuits with muxed oscillators are realized for passive optical network (PON) application. The CDR circuits are implemented with 0.35$\mu\textrm{m}$ CMOS process technology. Lock is accomplished on the first data transition and data are sampled in the optimal point. The experimental results show that the proposed CDR circuits recover the incoming 400Mbps-680Mbps burst mode input data without error.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.4
• /
• pp.188-193
• /
• 2003

This paper describes a novel burst-mode clock and data recovery (CDR) circuit which can be used for 622Mbps burst mode applications. The CDR circuit is basically a phase locked loop (PLL) having two phase detectors (PDs), one for the reference clock and the other for the NRZ data, whose operations are controlled by an external control signal. This CDR was fabricated in a 1-poly 5-metal $0.25{\;}\mu\textrm{m}$ CMOS technology. Jitter generation, burst/continuous mode data receptions were tested. Operational frequency range is 320Mhz~720Mhz and BER is less than 1e-12 for PRBS31 at 622Mhz. For the same data sequence, the extracted clock jitter is less than 8ps rms. Power consumption of 100mW was measured without I/O circuits.

• Korean Journal of Optics and Photonics
• /
• v.11 no.5
• /
• pp.330-334
• /
• 2000

A new pha~e lock loop (PLL) IS proposed and demonstrated fat clock recovery from 40 Gblt/s time-dIvision-multiplexed (TDM) optical pulse tri.lin, The proposed clock lecovery scheme lmproves the Jitter effecl cOlmng from the clock. pulse laser of harmonically-mode locked flber laser The cross-corrdation frequency component between the optical Signa] and an optical clock pulse tram is deteCled as a fonr-wave-mixing (FWM) SIgnal generated in SOA. The lock-in freqnency range of the clod. recovery IS found to be within 10 KHz. 0 KHz.