• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.225-228
• /
• 2009

The processing and characterization of ceramic nanocomposites, which produce bulk nanostructures with attractive mechanical properties, have been emphasized and introduced at Prof. Mukherjee's Lab at UC Davis. The following subjects will be introduced in detail in Part II, III, and IV. In Part II, the paper will describe a three-phase alumina-based nanoceramic composite demonstrating superplasticity at a surprisingly lower temperature and higher strain rate. The next part will show that an alumina-carbon nanotube-niobium nanocomposite produced fracture toughness values that are three times higher than that of pure nanocrystalline alumina. It was possible to take advantage of both fiber-toughening and ductile-metal toughening in this investigation. In the fourth section, discussed will be a silicon-nitride/silicon-carbide nanocomposite, produced by pyrolysis of liquid polymer precursors, demonstrating one of the lowest creep rates reported so far in ceramics at the comparable temperature of $1400^{\circ}C$. This was first achieved by avoiding the oxynitride glass phase at the intergrain boundaries. One important factor in the processing of these nanocomposites was the use of the electrical field assisted sintering method. This allowed the sintering to be completed at significantly lower temperatures and during much shorter times. These improvements in mechanical properties will be discussed in the context of the results from the microstructural investigations.

• 한국전기전자재료학회논문지
• /
• 제30권7호
• /
• pp.441-446
• /
• 2017

Aluminum nitride fibers were synthesized by carbothermal reduction and nitridation of precursor fibers obtained by electrospinning. The starting materials used to synthesize the AlN fibers were $Al(NO_3)_3{\cdot}9H_2O$ and urea. Polyvinylpyrrolidone with increasing viscidity was used as the carbon source to obtain a composite solution. The mixed solution was drawn into a plastic syringe with a stainless steel needle, which was used as the spinneret and connected to a 20 kV power supply. A high voltage was supplied to the solution to facilitate the formation of a dense net of fibers on the collector. The precursor fibers were dried at $100^{\circ}C$ and then heated to $1,400^{\circ}C$ for 1 h in a microwave furnace under $N_2$ gas flow for the carbothermal reduction and nitridation. X-ray diffraction studies indicated that the synthesized fibers consisted of the AlN phase. Field emission scanning electron microscopy studies indicated that the diameter of the calcined fibers was approximately 100 nm.

• 한국군사과학기술학회지
• /
• 제8권4호
• /
• pp.130-135
• /
• 2005

This paper presents application possibility of Lightweight Piezoceramic Composite Actuator(LIPCA) to suppress vibration of dynamic structures as an actuator. LIPCA is composed of a piezoelectric layer, a carbon/epoxy layer and glass/epoxy layers. When compared to the bare piezoelectric ceramic(PZT), LIPCA has advantages such as high performance, durability and reliability. In this study, performances of LIPCA have been estimated in an active vibration control system. Experiments were performed on an aluminum beam with cantilever configuration. In this test, strain gages and single LIPCA are attached on the aluminum beam with epoxy resin. Digital ON-OFF control algorithm is applied into the system to exhibit performance of LIPCA as actuator in active vibration control system. First, we performed static actuation test of bare PZT and LIPCA in order to show the superiority of LIPCA. Secondly, we carried out beam vibration control test using LIPCA. The results showed LIPCA could suppress free vibration of the aluminum beam, which means that LIPCA can be applied as an actuator to control vibration of dynamic structures.

• 한국재료학회지
• /
• 제10권5호
• /
• pp.364-368
• /
• 2000

섬유강화 세라믹스 복합재료의 파괴예측 가능성을 알아보기 위해서 탄소섬유와 WC분말입자를 전기 전도상으로 이용하여 재료 스스로가 파괴예측 기능을 가지도록 한 SiC섬유강화 $Si_3N_4$세라믹스기 복합재료를 1773K에서 1시간 동안 hot-press하여 제작하였다. 4점 굽힘 시험하는 동안 전기저항 변화를 측정하여 파괴예측 기능을 평가하였다. 그 결과 전기정항은 재료의 파괴거동과 밀접한 관계를 가지면서 변화함을 알았다. 특히 분말형태의 전기전도상의 첨가는 본 복합재료의 파괴과정을 낮은 응력단계로부터 예측하는데 유용하였다. 결과적으로 이러한 재료설RP의 신개 (파괴예측기능)의도입은 $Si_3N_4$기 세라믹스를 구조재료로 이용함에 있어서 큰 문제가 되고 있는 신뢰성 확보에 새로운 기능을 준다고 생각되었다. 생각되었다.

• 한국세라믹학회지
• /
• 제47권2호
• /
• pp.136-141
• /
• 2010

ACF/ZnO photocatalyst was synthesized by a sol-gel method using activated carbon fiber (ACF) and Zn $(NO_3)_2$ as precursors. Samples were characterized by Brunauer-Emmett-Teller measurements (BET), scanning electron microscope (SEM), X-ray diffraction (XRD), and energy dispersive X-ray (EDX). The XRD results showed that ACF/ZnO composites only included a hexagonal phase by heat-treated temperature at $400^{\circ}C$, $500^{\circ}C$, $600^{\circ}C$, and $700^{\circ}C$. The SEM analysis revealed that the ACF/ZnO composites did not exhibit any morphological changes of the catalyst surface according to the different heat-treated temperatures. The photocatalytic activity of the samples was tested for degradation of methylene blue (MB) solutions under ultraviolet (UV) light and ultrasonication respectively. The results showed that the photocatalytic activity of ACF/ZnO composites heat-treated at $500^{\circ}C$ was higher than other samples, which is ascribed to the fine distribution of ZnO particles on the surface of the ACF. In addition, an ultrasound of low power (50 W) was used as an irradiation source to successfully induce ACF/ZnO composites to perform sonocatalytic degradation of MB. Results indicated that the sonocatalytic method in the presence of ACF/ZnO composites is an advisable choice for the treatments of organic dyes.

• 한국세라믹학회지
• /
• 제49권2호
• /
• pp.185-190
• /
• 2012

The purpose of this study was to examine a possibility that fly ash could be used as raw material for carbonation by conducting the experiment on magnetic separation and hydration of fly ash that contained a large amount of CaO composite. Wet magnetic separation experiment was performed to remove the component of magnetic substance that contained fly ash, which aimed at increasing the content of CaO in the non-magnetic domain. The selected fly ash was used for hydration experiment before the TG-DTA, XRF and XRD analyses were made to confirm the Ca component that could be carbonated. Then, the fly ash was turned to a hydrate that was favorable to dissociation of $Ca^{2+}$ ion. As a result, the magnetic separation enabled detecting the content of CaO component by up to 61 wt% in the non-magnetic domain. Since the hydrate was confirmed, it is believed that the fly ash can be used as raw material for carbonation.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.571-576
• /
• 2011

Activity carbon (AC), Cu and $Cu_2O$ modified $TiO_2$ composites (Cu/$Cu_2O$-AC/$TiO_2$) were prepared using a sol-gel method. The characteristics of the composites were evaluated using Brunauer-Emmett-Teller (BET) surface area measurements, X-ray diffraction (XRD), energy dispersive X-ray (EDX) analysis and scanning electron microscope (SEM) analysis. A methyl orange (MO) solution under visible light irradiation was used to determine the photocatalytic activity. The degradation of MO was determined using UV/Vis spectrophotometry. $Cu_2O$, Cu and the cooperative effect of the AC increased the photo-absorption effect, thus increasing in photocatalytic activity.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.447-451
• /
• 2009

Continuous SiC fiber-reinforced SiC composites ($SiC_f$/SiC) were fabricated by electrophoretic deposition (EPD). Nine types of slurries with different powder contents, binder resin amounts and slurry pH were deposited on Tyranno$^{TM}$-SA fabrics by EPD at 135 V for ten minutes to determine the optimal conditions. Further EPD using the optimum slurry conditions was performed on fabrics with four different pyrolitic carbon (PyC) thicknesses. The density of the hot-pressed composites decreased with increasing PyC thickness due to the difficulty of infiltrating the slurry into the narrow gaps between the fibers. On the other hand, the mechanical strength increased with increasing PyC thickness despite the decrease in density, which was explained by the enhanced crack deflection with increasing PyC thickness. The $SiC_f$/SiC composites showed the highest density and flexural strength of 94% and 342 MPa, respectively, showing EPD as a feasible method for dense $SiC_f$/SiC fabrication.

• Journal of Ceramic Processing Research
• /
• 제20권1호
• /
• pp.18-23
• /
• 2019

Chemical looping combustion (CLC) is a promising carbon capture and storage (CCS) technology whose efficiency and cost primarily relies on the oxygen carrier materials used. In this paper, gadolinium-doped ceria (GDC, Ce0.9Gd0.1O1.95) was added as a promoter to improve the oxygen transfer rate of MgMnO3-δ oxygen carrier materials. Increasing GDC content significantly increased the oxygen transfer rate of MgMnO3-δ-GDC composites for the reduction reaction due to an increase in the surface adsorption of CH4 via oxygen vacancies formed on the surface of the GDC. On the other hand, the oxygen transfer rate for the oxidation reaction decreased linearly with increasing GDC content due to the oxygen storage ability of GDC. Adsorbed oxygen molecules preferentially insert themselves into oxygen vacancies of the GDC lattice rather than reacting with (Mg,Mn)O to form MgMnO3-δ during the oxidation reaction.

• The Korean Journal of Ceramics
• /
• 제5권4호
• /
• pp.353-356
• /
• 1999

Highly proten-conductive elastic composites have been successfully prepared from $H_3PO_4$-doped silica gel and styrene-ethylene-butylene-styrene block elastic copolymer. In addition solid state electric double-layer capacitors have been fabricated using the composite as an electrolyte and activated carbon powders(ACP) hybridized with the composite as a polrizable electrode. The cyclic voltammogram of the electric double-layer capacitor fabricated demonstrated that electric charge was stored in the elecric double-layer at the interface between the polarizable electrode and the electrolyte. The value of capacitance of the capacitor was 10 F/(gram of total ACP), which was comparable to that of the capacitors using conventional liquid electrolytes.