• Publications of The Korean Astronomical Society
• /
• v.32 no.1
• /
• pp.257-261
• /
• 2017

We built a $8{\mu}m$ selected sample of galaxies in the NEP-AKARI field by defining 4 redshift bins with the four AKARI bands at 11, 15, 18 and 24 microns (0.15 < z < 0.49, 0.75 < z < 1.34, 1.34 < z < 1.7 and 1.7 < z < 2.05). Our sample contains 4079 sources, 599 are securely detected with Herschel/PACS. Also adding ultraviolet (UV) data from GALEX, we fit the spectral energy distributions using the physically motivated code CIGALE to extract the star formation rate, stellar mass, dust attenuation and the AGN contribution to the total infrared luminosity ($L_{IR}$). We discuss the impact of the adopted attenuation curve and that of the wavelength coverage to estimate these physical parameters. We focus on galaxies with a luminosity close the characteristic $L^*_{IR}$ in the different redshift bins to study the evolution with redshift of the dust attenuation in these galaxies.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.848-853
• /
• 2010

We have grown GaN nanowires by the low pressure MOCVD method on Ni deposited oxidized Si surface and have established optimum conditions by observing surface microstructure and its photoluminescence. Optimum growth temperature of $880^{\circ}C$, growth time of 30 min, TMG source flow rate of 10 sccm have resulted in dense nanowires on the surface, however further increase of growth time or TMG flow rate has not increased the length of nanowire but has formed nanocrystals. On the contrary, the increase of ammonia flow has increased the length of nanowires and the coverage of nanowire over the surface. The shape of nanowire is needle-like with a Ni droplet at its tip; the length is tens of micron with more than 40 nm in diameter. Low temperature photoluminescence obtained from the sample at optimum growth condition has revealed several peaks related to exciton decay near band-edge, but does not show any characteristic originated from one dimensional quantum confinement. Strong and broad luminescence at 2.2 eV is observed from dense nanowire samples and this suggests that the broad band is related to e-h recombination at the surface state in a nanowire. The current result is implemented to the nanowire device fabrication by nanowire bridging between micro-patterned neighboring Ni catalysis islands.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.176-181
• /
• 2009

In this work, a new type of DSCs based on nanoporous FTO structure is being developed for research aimed at low-cost high-efficiency solar cell application. The nanoporous FTO materials have been prepared through the sol-gel combustion method followed by thermal treatment at $450{\sim}850[^{\circ}C]$. The properties of the nanoporous FTO materials were investigated by IR spectra, BET and TEM analyses, and the photovoltaic performance of the prepared DSCs were examined. It can be seen from the result that the nanoporous FTO exhibited good transparent conductive properties, well suited for DSCs application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.10
• /
• pp.760-765
• /
• 2013

PID (potential induced degradation) of PV module is the degradation of module due to the high potential difference between the front surface of solar cells and ground when PV modules operate under high humidity and temperature conditions. PID is generally derived from the positive sodium ions in front glass that are accumulated on P-type solar cells. Therefore, some papers for the electrical characteristic of only front components as glass, EVA sheet, solar cell under PID generation condition were revealed. In this paper, we analyzed the different outputs of module with PID by considering the all parts of module including the back side elements such as glass, back sheet. Mini modules with one solar cell were fabricated with the various parts on front and back sided of module. To generate PID of module in a short time, the all modules were applied.1,000 V in $85^{\circ}C$, 85% RH. The outputs, dark IV curves and EL images of all modules before and after experiments were also measured to confirm the main components of module for PID generation. From the measured results, the outputs of all modules with front glass were remarkably reduced and the performances of modules with back and front glass were greatly deteriorated. We suggest that the obtained data could be used to reduce the PID phenomenon of diverse modules such as conventional module and BIPV (building integrated photovoltaic) module.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.261-263
• /
• 2005

In the extra and ultra high voltage system, the coupling capacitor voltage transformer (CCVT) measures the primary voltage with a small scale of voltage transformer (VT). However, the CCVT generates errors caused by the hysteresis characteristics of iron core and by the ferroresonance, inevitably. This paper proposes a compensation algorithm for the secondary voltage of a CCVT considering the hysteresis characteristics of an iron core. The proposed algorithm calculates the seconda교 current of a VT by summing the current flowing the ferroresonance circuit and the burden current; it estimates the secondary voltage of a VT; then the core flux is calculated by integrating of the secondary voltage of a VT, then estimates the exciting current using ${\lambda}-i$ characteristic of the core. The method calculates a primary voltage of a VT considering the estimated primary current. Finally, the correct voltage is estimated by compensating the voltage across the inductor and capacitor. The performance of the proposed algorithm was tested in a 345kV transmission system. The test results show that the proposed method can improve the accuracy of the seconda교 voltage of a CCVT.

• Transactions of Materials Processing
• /
• v.27 no.4
• /
• pp.250-256
• /
• 2018

Oxygen-free copper (OFC) was prepared as a 90 mm cube and then processed with Multi-Axial Diagonal Forging - Initialization of Prior manufacturing History (MADF). The MADF process has been newly developed as a severe plastic deformation method. The MADF process consists of upset forging with a thickness reduction of 30% and diagonal forging with a diagonal angle of $135^{\circ}$. 1 cycle process consists of a 12 passes forging process. In order to analyze the characteristic changes according to the number of iterations, 1, 2, and 3 cycles of the MADF process were performed. The OFC specimens were MADF processed without surface cracks up to 3 cycles. The microstructure, hardness and tensile test of processed materials were analyzed to study the change of material properties according to the amount of MADF process. The results showed that the MADF process effectively refined the microstructure and increased the strength of OFC. In the case of specimens processed for more than 2 cycles, the grains of all measurement regions were refined to be less than $7{\mu}m$ of grain size. The 1 cycle MADF processed OFC showed the highest mechanical properties with the hardness of 132 HV and tensile strength of 395 MPa. Hardness and strength seemed to be saturated when processed over 2 cycles.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.2
• /
• pp.36-44
• /
• 2013

The objectives of this study were to identify the characteristics of shallow groundwater from the oil-contaminated site for a long period and to evaluate the applicability of biopile technology to treat the soil excavated from it. The eight monitoring wells were installed in the contaminated site and pH, Electrical Conductivity (EC), Dissolved Oxygen (DO), Oxidation Reduction Potential (ORP), Temperature and the concentrations of major ions and pollutants were measured. The VOCs in soil gas were monitored during biopile operation and TPH concentration was analyzed at the termination of the experiment. The pH was 6.62 considered subacid and EC was 886.19 ${\mu}S/cm$. DO was measured to be 2.06 mg/L showing the similar characteristic of deep groundwater. ORP was 119.02 mV indicating oxidation state. The temperature of groundwater was measured to be $16.97^{\circ}C$. The piper diagram showed that groundwater was classified as Ca-$HCO_3$ type considered deep groundwater. The ground water concentration for TPH, Benzene, Toluene, Xylene of the first round was slightly higher than that of the second round. The concentration of carbon dioxide of soil gas was increased to 1.3% and the concentration of VOCs was completely eliminated after the 40 days. The TPH concentration showed 98% remediation efficiency after the 90 days biopile operation.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.241-247
• /
• 2000

77 K와 self-field에서 22 A 의 Ic 를 갖는 길이 120 m, 19-심 Bi-2223상 선재를 제조하여, 두 개의 double pancake 코일로 구성된 proto-type 고온초전도 자석을 설계, 제작하여 이 자석에서의 4.2 K와 77 K에서의 I-V 특성과 운전 특성을 평가한 결과, 이 자석은 77 K 등온조건에서는 9.5 A 의 Ic를, 77 K 헬륨가스 속에서는 8.3 A 의 Ic를 나타내었고, 4.2 K 등온조건에서는 93.7 A 의 Ic와 102 A 의 Iq를, 4.2K헬륨가스 속에서는 88.4A의 Ic 와 92.0 A 의 Iq를 나타내어, 이 자석은 4.2 K 와 77 K 의 등온조건에서 각각 0.58 T 와 0.06 T 의 자장을 발생하였는데, 이는 해석적 방법으로 계산한 결과와 잘 일치하였다. 그리고 이 자석이 전도냉각되어 4.2 K 에서 운전될 때의 안정성 특성평가로서, Ic 보다 약간 큰 전류인 89 A 를 인가한 결과, 전류인가 후 82.6초 후에 quench가 발생하였는데, 이 quench는 네 번째 pancake의 전류도입선부 연결부에서와 약간 늦지만 첫 번째 pancake의 전류도입선부 연결부에서 거의 동시에 개시되어 전체로 파급된 것으로 사료되었는데, Ic 가 낮은 첫번째 pancake에서 더 높은 전압 강하가 나타났다. 또한 장착된 heater를 통하여 77 K 에서 8.9 A 의 전류로 운전되고 있는 코일에 146 joule 의 열을 가했을 때 quench 가 일어났는데, 이때 quench 는 방위각 방향의 Bi-2223/Ag 선재를 따라서 보다 Kapton 절연층을 관통하는 선재의 반경방향으로 훨씬 빨리 전파하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.1
• /
• pp.52-58
• /
• 2006

Single-electron transistor (SET)-based logic cells and SET/FET hybrid integrated circuits have been fabricated on SOI chips. The input-output voltage transfer characteristic of the SET-based complementary logic cell shows an inverting behavior where the output voltage gain is estimated to be about 1.2 at 4.2K. The SET/FET output driver, consisting of one SET and three FETs, yields a high voltage gain of 13 and power amplification with a wide-range output window for driving next circuit. Finally, the SET/FET literal gate for a multi-valued logic cell, comprising of an SET, an FET and a constant-current load, displays a periodic voltage output of high/low level multiple switching with a swing as high as 200mV. The multiple switching functionality of all the fabricated logic circuits could be enhanced by utilizing a side gate incorporated to each SET component to enable the phase control of Coulomb oscillations, which is one of the unique characteristics of the SET-based logic circuits.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.92-95
• /
• 2003

초전형 센서의 특성 평가 방법에는 여러 가지 방법들이 존재하며, 이에 대한 표준화된 특성 평가방법의 개발이 필요로 한다. 측정 평가의 방법이나 조건 등에 따라서 평가 결과가 크게 변할 수 있는 사항들이며, 따라서 국내 뿐 아니라 대외적으로 다른 나라의 제품들과 신뢰성을 가지고 경쟁을 하기 위해서는 평가항목이나 평가방법의 표준화가 절실하게 요구된다. 초전형 적외선 센서를 평가하는 항목에는 기본적으로 입력에 대한 출력신호의 크기를 평가하는 감도(responsivity), 잡음과 관련되어 센서가 검출할 수 있는 최소의 신호를 나타내는 NEP(Noise Equivalent Power)와 이것을 센서의 감지 면적으로 정규화 시킨 검출능(detectivity), 응답 속도를 나타내는 시정수(time constant)가 있으며 이러한 항목들이 표준화의 대상이 된다. 본 실험에서는 기존의 상용화된 센서들을 가지고 초전형 적외선 센서의 특성을 측정 하였다. 특성을 측정할 때 다른 요인들 보다 노이즈로 인한 영향이 상당히 크므로 측정시 노이즈 발생 문제를 해결하는 방법으로 본 논문에서는 센서 측정에 사용되는 증폭 회로에서 노이즈를 해결하려고 하였다. 우리는 증폭 회로구성에서 노이즈를 제거하기 위해서 신호입력단과 전압 압력에 잡음제거 필터로 R, C를 사용하였다. 회로설계로 제작된 증폭회로와 측정 장치를 가지고 측정을 한 결과 센서의 감도는 $3.0mV_{p-p}$, 응답시간은 20ms정도의 값으로 가장 일반적인(typical) 값을 보인다.