• 한국항해학회지
• /
• 제14권1호
• /
• pp.1-7
• /
• 1990

A theoretical model for the over-all ship's magnetism was developed, on the assumption that the magnetism of a three-island type vessel can be regarded as that of the prolate spheroidal magnetic body. Modelled values were determined by the simulation on the base of the theoretical analysis of the magnetic field around the above-mentioned magnetic body. The real values were made of the data observed from four different three-islands type vessels alongside the piers. The agreement between the modelled and real values was found to be accurate.

• 대한치과기공학회지
• /
• 제37권4호
• /
• pp.205-212
• /
• 2015

Purpose: The objective of this study was to compare the surface roughness according to polishing process in conventional laboratory techniques used for polishing three different acrylic denture base resins. Materials and methods: Specimen preparation and surface polishing procedures were conducted to manufacturer's recommendation with three heat-polymerized denture base resins. Surface roughness and gloss were measured by a contact type tester and a LED gloss checker using thickness 2 mm and diameter 10 mm. There were five specimens for each acrylic resin material and polishing procedures. Mean average surface roughness (Ra) values of each specimen group were analyzed using a one-way ANOVA analysis of variance and Scheffe's post hoc test. Surfaces after surface roughness and gloss testing according to each polishing process were evaluated under a stereoscopic microscope. Results: The highest mean average surface roughness was measured($Ra=2.43{\pm}0.47$) for surfaces finished with a denture tungsten carbide bur in Triplex. The lowest surface roughness values ($Ra=0.11{\pm}0.07$) were determined in Vertex polished with a lathe. In addition, all materials revealed that surface roughness determined highly in HP1 and HP2 than other procedures. All correlation between surface roughness and gloss showed highly with three heat-polymerized resins. Specially, topmost correlation revealed than other material in Triplex. Significant differences in mean average surface roughness were found between polishing process used high speed lathe and low speed hand-piece. Conclusion: Laboratory polishing used to high speed was found to produce the smoothest surface of heat-polymerized denture base acrylic resin. Therefore, we recommended that high polishing process need to get smooth surface.

• 대한치과기공학회지
• /
• 제46권2호
• /
• pp.28-35
• /
• 2024

Purpose: To evaluate the three-dimensional trueness of upper and lower denture bases produced using a digital light processing (DLP) printer and immersed in a constant-temperature water bath. Methods: An edentulous model was prepared and fitted with denture bases and occlusal rims manufactured using base plate wax. After scanning the model, denture bases, and occlusal rims, complete denture designs were created. Using the designs and a DLP printer, 10 upper and 10 lower complete dentures were manufactured. Each denture was scanned before (impression surface of upper denture base before constant temperature water bath [UBC] and impression surface of lower denture base before constant temperature water bath [LBC] groups) and after (impression surface of upper denture base after constant temperature water bath [UAC] and impression surface of lower denture base after constant temperature water bath [LAC] groups) immersion in the constant-temperature water bath. Scanned files were analyzed by comparing reference and scanned data, with statistical analysis conducted using the Kruskal-Wallis test (α=0.05). Results: Statistical analysis revealed no significant differences between the UBC and LBC groups, nor between the UAC and LAC groups (p>0.05). However, significant differences were observed between the UBC and UAC groups and between the LBC and LAC groups, i.e., before and after the constant-temperature water bath for both maxillary and mandibular denture bases (p<0.05). Conclusion: Denture bases not immersed in the constant-temperature water bath (UBC and LBC groups) exhibited error values within 100 ㎛, whereas those immersed in the water bath (UAC and LAC groups) showed error values exceeding 100 ㎛.

• The Journal of Advanced Prosthodontics
• /
• 제16권4호
• /
• pp.231-243
• /
• 2024

PURPOSE. The objective of the study was to analyze the impact of cement, bonding pretreatment, and ceramic abutment material on the overall color results of CAD-CAM ceramic crowns bonded to titanium-based hybrid abutments. MATERIALS AND METHODS. For single implant restoration of a maxillary lateral incisor a total of 51 CAD-CAM-fabricated monolithic lithium disilicate crowns were fabricated and subsequently bonded onto 24 lithium disilicate Ti-base abutments, 24 zirconia Ti-base abutments and 3 resin abutment replicas as a control group. The 48 copings were cemented with three definitive and one provisional cement on both grit-blasted and non-blasted Ti-bases. The color of each restoration and surrounding artificial gingiva was measured spectrophotometrically at predefined measuring points and the CIELAB (ΔE_ab) color scale values were recorded. RESULTS. The color outcome of ceramic crowns bonded to hybrid abutments and soft tissues was affected differently by cements of different brands. Grit-blasting of Ti-bases prior to cementing CAD-CAM copings affected the color results of allceramic crowns. There was a significant difference (P = .038) for the median ΔE value between blasted and non-blasted reconstructions at the cervical aspect of the crown. Full-ceramic crowns on zirconia Ti-base abutments exhibited significantly lower ΔE values below the threshold of visibility (ΔE 1.8). In all subcategories tested, the use of a highly opaque temporary cement demonstrated the lowest median ΔE for both the crown and the artificial gingiva. CONCLUSION. Various cements, core ceramic materials and airborne particle abrasion prior to bonding can adversely affect the color of Ti-base supported ceramic crowns and peri-implant soft tissue. However, zirconia CAD-CAM copings and an opaque cement can effectively mask this darkening.

• 한국포장학회지
• /
• 제7권1호
• /
• pp.16-20
• /
• 2001

In order to optimize designing process of corrugated fiberboard boxes for agricultural products, first of all, compression strength of each liner were experimentally evaluated on the various conditions of relative humidity and analyzed by liner regression analysis. At the 66 percents of relative humidity, IK(imported kraft liner) liner board lost little of its compression strength compared to others. At the relative humidity 93 percents, KA liner board lost its compression strength only 40 percents while SK liner board lost up to 56 percents. From the result of prediction modeling of ring crush strength in various humidity conditions, R square values were ranged from 0.59 to 0.97. At 56 percents of RH or below, R square values were relatively low, but at 66 percents of RH or higher, the values were 0.85 or higher. The significance values were lower than 0.001 at every RH condition. Level of significance of experimented values was about 80 percents of predicted values and R square values were between 0.89 to 0.95.

• 대한치과교정학회지
• /
• 제19권1호
• /
• pp.137-151
• /
• 1989

To help arrive at a more accurate diagnosis of anteroposterior apial base relationship on each individual case, it is important to compare the interpretation in the same population on a longitudinal basis. The author studied on the changes of the anteroposterior apical base relationship using serial lateral cephalometric roentgenograms of 15 boys and 27 girls aged from 6 to 13 years of Korean children. Following results were obtained 1. Norms of Korean boys and girls were established. 2. With ages, there was a gradual decrease of ANB, AXB angle, and there was a gradual increase of facial angle, A-B plane angle, APDI. 3. Wits appraisal does not change significantly with ages. 4. No significant differences were observed in the changes between male and female subjects for all absolute values between the ages of 6 years and 12 years, but significant differences were observed in ANB, AXB, A-B plane angle of the age of 13 years. No significant differences were observed in the changes between male and female subjects for all incremental values between the ages of 6 years and 13 years.

• 대한치과교정학회지
• /
• 제14권2호
• /
• pp.217-231
• /
• 1984

Many investigators have studied the growth changes of craniofacial complex to obtain important informations and standard values with which attempts at prediction of growth and treatment results have been under exploration. The author analyzed 360 cephalometric roentgenograms of 40 boys and 50 girls taken from the ages of 6 to 9 to assess the growth changes of craniofacial complex and to establish Korean norms by Ricketts' analysis method. 17 Landmarks, 10 planes and 8 angles were plotted and measured by linearly and angularly. The results were as follows: 1. The author made the tables of means, standard deviations from the measured values. 2. The item which showed significant difference between males and females in longitudinal study was facial axis length. 3. Items which show significant changes during 3 years were cranial base length, facial axis length, lower incisor to APO, Upper molar to PTV in males, and cranial base length, facial axis length, upper molar to PTV in females. 4. The correlations between cranial base length and facial axis length to body height and weight were higher in males than in females throughout the items.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.401-414
• /
• 2010

Top Base Foundation(TBF) is a stabilization method for light weight structures particularly in the soft ground. It is widely used for the increment of bearing capacity and restraining settlement of foundations when the bearing capacity of ground is not enough. However, when the design values from exiting Japanese standard are compared with the observation values from the field measurement, the bearing capacity of exiting standard estimated smaller For this reason, it is necessary to establish more reasonable prediction technique considering to understand the behavior of TBF in soft ground. In this study, 1/5 scale model tests were performed in the laboratory. Also, full scale tests were carried out in order to investigate the behavior of TBF with various shapes. In addition, about 100 sites measurement data were evaluated to investigate the behavior of TBF in various ground conditions. Based on the results of the model tests and field measurement data, it was possible to establish more reasonable the bearing capacity equation of TBF considering various N-value of soil, the effect of underground water and failure shapes.

• 대한치과기공학회지
• /
• 제22권1호
• /
• pp.79-88
• /
• 2000

The objective of this finite element method study was to analyze the stress distribution induced in a maxillary central incisor Ni-Cr base metal coping ceramic crowns with various margin design. Margin designs of crown in this experiment were knife-edge metal margin on chamfer finishing line of tooth preparation(M1), butt metal margin on shoulder finishing line(M2), reinforced butt metal margin on shoulder finishing line(M3), beveled metal margin on bevelde shoulder finishing line(M4). Two- dimensional finite element models of crown designs were subjected to a simulated biting force of 100N which was forced over porcelain near the lingual incisal edge. Base on plane stress analysis, the maxium von Miss stresses(Mpa) in porcelain venner was 0.432, in metal coping was 0.579, in dentin abutment was 0.324 for M1 model, and M2 model revealed in porcelain was 0.556, in metal coping was 0.511, in dentin was 0.339, and M3 model revealed in porcelain was 0.556, in metal coping was 0.794, in dentin was 0.383 for M4 model. All values of each material in metal-ceramic crown were much below the critical failure values.

• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.115-124
• /
• 1989

본 연구에서는 2상계 스테인리스강의 모재,용접재 및 용접후 열처리재 3종류의 경우에 대하여 피로크랙 전파특성을 피로크랙의 하한계치 근방에서 금속조직적인 영향을 검토하기 위하여, 각 조건에 대한 피로크랙 전파속도의 하한 계치를 구하였고 피로식검후의 파단면을 주사전자현미경(SEM)으로 관찰하였다. 용접재에 대하여는 용착부 부근 용접열영향부의 입경측정, .alpha./.gamma.상의 체적비교율의 변화량 측정 및 용접재와 용접후열처리재의 잔유응력분포측정을 통하여 피로크랙의 하한계특성에 미치는 여러가지 영향인자에 대하여 검토하였다.