• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.130-131
• /
• 2005

In the era of submicron devices, super ultra thin gate oxide characteristics are required. Titanium silicide process has studied gate oxide reliability and dielectric strength characteristics as the composition of gate electrode. In this study the author observed process characteristics on MOS structure. In view point of the process characteristics of MOS capacitor, the oxygen & Ti, Si2 was analyzed by SIMS analysis on before and after annealing with 1,2 step silicidation, the Ti contents[Count/sec]of $9.5{\times}1018$ & $6.5{\times}1018$ on before and after 2'nd anneal. The oxygen contents[Count/sec] of $4.3{\times}104$ & $3.65{\times}104$, the Si contents[Count/sec] of $4.2{\times}104$ & $3.7{\times}104$ on before and after 2'nd anneal. The rms value[A] was 4.98, & 4.03 on before and after 2'nd anneal.

• Journal of Surface Science and Engineering
• /
• v.35 no.6
• /
• pp.377-382
• /
• 2002

We investigated the appropriate wet cleaning process for Co-Ti-Si compounds formed on top of cobalt disilicide made from Co/Ti deposition and two rapid thermal annealing (RTA). We employed three wet cleaning processes, WP1 ($H_2$SO$_4$ etchant), WP2 ($NH_4$OH etchant), and WP3 which execute sequentially WP1 and WP2 after the first RTA. All samples were cleaned with BOE etchant after the second RTA. We characterized the sheet resistance with process steps by a four-point probe, the microstructure evolution by a cross detail sectional transmission electron microscope, a Auger depth profiler, and a X-ray diffractometer (XRD). We confirmed WP3 wet cleaning process were the most suitable to remove CoTiSi layer selectively.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.2
• /
• pp.427-430
• /
• 2008

BaTiO3 and SrTiO3 thin films were fabricated on Pt/Ti/SiO2/Si substrate by the pulsed laser deposition process. The dependence of the deposited film quality upon the partial oxygen pressure during the deposition process was importantly examined. Regardless of the oxygen pressure, the as-deposited films were not fully crystallized. However, the film deposited at low oxygen pressure became well crystallized after the annealing process. It was concluded, therefore, that the partial oxygen pressure is reduced as low as possible during the deposition process and then anneal the as-deposited samples at ambient pressure to fabricate the well crystallized SrTiO3 and BaTiO3 films by laser ablation.

• Journal of Korea Foundry Society
• /
• v.35 no.6
• /
• pp.141-146
• /
• 2015

Aluminum-based hybrid parts were fabricated through a compound casting process with Al or Cu inserts which can be used for applications requiring high conductivity. Because the interface stability between the insert and the aluminum matrix is important, the effects of process variables on the interfacial adhesion strength were investigated. Additions of Cu and Mg to Al melt were found to enhance the adhesion strength, though the melt fluidity was slightly deteriorated when a small amount of Mg was added. An isothermal heating process after casting further improved the strength. However AlCu intermetallic compounds formed and their thickness increased during the heating process. As a result, deterioration in the interfacial adhesion strength was observed after an excessive annealing treatment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.195-196
• /
• 2005

In recent years, as the needs of MOS's a high quality is desired to get the superior electrical characteristics and reliability on MOSFET. As an alternative gate dielectric have drawn considerable alternation due to their superior performance and reliability properties over MOSFET, 2'nd silicidation formation process has been proposed as a dielectric growth/annealing process. In this study the author observed process characteristics on MOS structure. In view points of the process characteristics of MOS capacitor, the oxygen & polysilicon was analyzed by SIMS analysis on l'st & 2'nd Ti process, the oxygen and Si2 contents[Count/sec] of 1.5e3 & 3.75e4 on l'st process and l.1e3 & 2.94e4 on 2'nd process, the Ti contents' of 8.2e18 & 6.5e18 on 1'st and 2'nd process. The sheet resistance[$\Omega/sq.$] was 4.5 & 4.0, the film stress[dyne/cm 2] of 1.09e10 & 1.075e10 on l'st and 2'nd process. I could achieved the superior MOS characteristics by 2'nd silicidation process.

• Journal of the Korean Vacuum Society
• /
• v.10 no.3
• /
• pp.328-334
• /
• 2001

The characteristics of $NO/N_2O$ nitrided oxide and reoxidized nitrided oxide being studied as super thin gate oxide and gate dielectric layers of nonvolatile semiconductor memory(NVSM) was investigated by dynamic secondary ion mass spectrometry(D-SMS), time-of-flight secondary ion mass spectrometry(ToF-SIMS), and x-ray photoelectron spectroscopy (XPS). The specimen was annealed in $NO/N_2O$ ambient after initial oxide process. The result of D-SIMS exhibits that the center of nitrogen exists at the initial oxide interface and the distribution of nitrogen is wider in the annealing process with $N_2O$ than with NO annealing process. For investigating the condition of nitrogen that exists within the nitrided oxide, ToF-SIMS and XPS analysis were carried out. It was shown that the center of nitrogen investigated by D-SIMS was expected the SiON chemical bonds. The nitrogen near the newly formed reoxide/silicon substrate interface was appeared as $Si_2NO$ chemical bonds, and it is agreed with the distribution of SiN and $Si_2NO$ species by ToF-SIMS.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.10
• /
• pp.754-759
• /
• 2013

Aluminum oxide($Al_2O_3$) film deposited by atomic layer deposition (ALD) is known to supply excellent surface passivation properties on crystalline Si surfaces. Since $Al_2O_3$ has fixed negative charge, it forms effective surface passivation by field effect passivation on the rear side in p-type silicon solar cell. However, $Al_2O_3$ layer formed by ALD process needs very long process time, which is not applicable in mass production of silicon solar cells. In this paper, plasma-assisted ALD(PA-ALD) was applied to form $Al_2O_3$ to reduce the process time. $Al_2O_3$ synthesized by ALD on c-Si (100) wafers contains a very thin interfacial $SiO_2$ layer, which was confirmed by FTIR and TEM. To improve passivation quality of $Al_2O_3$ layer, the deposition temperature was changed in range of $150{\sim}350^{\circ}C$, then the annealing temperature and time were varied. As a result, the silicon wafer with aluminum oxide film formed in $250^{\circ}C$, $400^{\circ}C$ and 10 min for the deposition temperature, the annealing temperature and time, respectively, showed the best lifetime of 1.6ms. We also observed blistering with nanometer size during firing of $Al_2O_3$ deposited on p-type silicon.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.230-234
• /
• 2009

It is significant technique to increase competitiveness that solar cells have a high energy conversion efficiency and cost effectiveness. When making high efficiency crystalline Si solar cells, evaporated Ti/Pd/Ag contact system is widely used in order to reduce the electrical resistance of the contact fingers. However, the evaporation process is no applicable to mass production because high vacuum is needed. Furthermore, those metals are too expensive to be applied for terrestrial applications. Ni/Cu/Ag contact system of silicon solar cells offers a relatively inexpensive method of making electrical contact. Ni silicide formation is one of the indispensable techniques for Ni/Cu/Ag contact sytem. Ni was electroless plated on the front grid pattern, After Ni electroless plating, the cells were annealed by RTP(Rapid Thermal Process). Ni silicide(NiSi) has certain advantages over Ti silicide($TiSi_2$), lower temperature anneal, one step anneal, low resistivity, low silicon consumption, low film stress, absence of reaction between the annealing ambient. Ni/Cu/Ag metallization scheme is an important process in the direction of cost reduction for solar cells of high efficiency. In this article we shall report an investigation of rapid thermal silicidation of nickel on silngle crystalline silicon wafers in the annealing range of $350-390^{\circ}C$. The samples annealed at temperatures from 350 to $390^{\circ}C$ have been analyzed by SEM(Scanning Electron Microscopy).

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.41.2-41.2
• /
• 2011

Recently, scaling down of ULSI (Ultra Large Scale Integration) circuit of CMOS (Complementary Metal Oxide Semiconductor) based electronic devices become much faster speed and smaller size than ever before. However, very narrow interconnect line width causes some drawbacks. For example, deposition of conformal and thin barrier is not easy moreover metallization process needs deposition of diffusion barrier and glue layer. Therefore, there is not enough space for copper filling process. In order to overcome these negative effects, simple process of copper metallization is required. In this research, Cu-V thin alloy film was formed by using RF magnetron sputter deposition system. Cu-V alloy film was deposited on the plane $SiO_2$/Si bi-layer substrate with smooth and uniform surface. Cu-V film thickness was about 50 nm. Cu-V layer was deposited at RT, 100, 150, 200, and $250^{\circ}C$. XRD, AFM, Hall measurement system, and XPS were used to analyze Cu-V thin film. For the barrier formation, Cu-V film was annealed at 200, 300, 400, 500, and $600^{\circ}C$ (1 hour). As a result, V-based thin interlayer between Cu-V film and $SiO_2$ dielectric layer was formed by itself with annealing. Thin interlayer was confirmed by TEM (Transmission Electron Microscope) analysis. Barrier thermal stability was tested with I-V (for measuring leakage current) and XRD analysis after 300, 400, 500, 600, and $700^{\circ}C$ (12 hour) annealing. With this research, over $500^{\circ}C$ annealed barrier has large leakage current. However V-based diffusion barrier annealed at $400^{\circ}C$ has good thermal stability. Thus, thermal stability of vanadium-based thin interlayer as diffusion barrier is good for copper interconnection.

• Journal of Magnetics
• /
• v.9 no.4
• /
• pp.101-104
• /
• 2004

The crystallization behaviours of nanocomposite made by a function of quenching rate (roller speed) were studied. The results showed that there was one step c$\mathbb{r}$ystallization process for the alloy quenched at roller speed of 32 m/s, which could be shown as, Am (amorphouse) + ${\alpha}-Fe/Nd_2Fe_{14}B$ ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{14}B$ . For the alloy quenched at roller speed of 40 m/s, there was steps crystallization process taking place at different temperatures, which could be shown as, Am ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{23}B_3+Nd_2Fe_{14}B+Am`$ ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{14}B$. The presence of transition phase ($Nd_2Fe_{23}B_3$) was harmful to get fine and uniform grain size during crystallization process. Uniform microstructures and high magnetic properties could be attained for the as-quenched alloy containing less amorphous phase and no presence of transition phase during annealing treatment. For the alloy prepared at roller speed of 32 m/s, the following properties were obtained, $B_r= 0.904 T,_iH_c = 801 kA/m, (BH)_{max} = 122 kJ/m^3 and M_r/M_s = 0.6$.