• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.247-252
• /
• 2003

In this paper, we made four types of metal particle $Al_2$O$_3$ barrier reactors with and without dielectric of BaTiO$_3$ between metal particle and $Al_2$O$_3$ barrier to investigate NOx removal characteristic and the effect of dielectric on Nox removal. And Nox removal rate is measured when sludge pellets are put at down stream of plasma reactor. Nox removal rate in the reactor with $Al_2$O$_3$ barrier is much better than that in the reactor without $Al_2$O$_3$ barrier, Nox removal rate is not so good in metal particle-Al$_2$O$_3$ barrier reactor with BaTiO$_3$ between metal particle and $Al_2$O$_3$ barrier, however, Nox removal rate is about 40% in metal particle-Al$_2$O$_3$ barrier reactor with TiO$_2$. The most of NO is conversed to NO$_2$ in these kind of reactor. When sludge pellets are put at down stream of plasma reactor, Nox removal rate is greatly improved up to 90%. It indicates that sludge pellets have great effect on the NO$_2$ removal and the improvement of Nox removal rate, however, dielectric materials between metal particle and $Al_2$O$_3$ barrier have not effect. Organic materials included in sludge may react with NO$_2$ and ozone so that Nox removal rate is greatly improved.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.66-67
• /
• 2002

Magnetic tunnel junction에서는 spin의 tunneling이 가장 기본적인 현상이기 때문에 tunnel junction의 특성은 tunnel barrier의 성질에 크게 의존한다. Tunnel barrier로는 지금까지 $Al_2$O$_3$가 주로 사용되고 있다. 하지만 $Al_2$O$_3$의 경우는 barrier height가 2-3 eV로 높기 때문에 저 저항의 tunnel junction을 형성하기 위해서는 Al의 두께가 1nm 이하로 낮아져야 한다. 따라서 이를 극복하기 위해서 $Al_2$O$_3$ 보다 낮은 barrier height를 갖는 절연막을 tunnel barrier로 사용하고자 하는 연구가 많이 진행되고 있다 (예를 들면 TaOx [1], ZrOx [2], GaOx [3], and HfOx [4]). (중략)

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.110.1-110.1
• /
• 2012

Recently, advances in ZnO based oxide semiconductor materials have accelerated the development of thin-film transistors (TFTs), which are the building blocks for active matrix flat-panel displays including liquid crystal displays (LCD) and organic light-emitting diodes (OLED). However, the electrical performances of oxide semiconductors are significantly affected by interactions with the ambient atmosphere. Jeong et al. reported that the channel of the IGZO-TFT is very sensitive to water vapor adsorption. Thus, water vapor passivation layers are necessary for long-term current stability in the operation of the oxide-based TFTs. In the present work, $Al_2O_3$ and $TiO_2$ thin films were deposited on poly ether sulfon (PES) and $SnO_x$-based TFTs by electron cyclotron resonance atomic layer deposition (ECR-ALD). And enhancing the WVTR (water vapor transmission rate) characteristics, barrier layer structure was modified to $Al_2O_3/TiO_2$ layered structure. For example, $Al_2O_3$, $TiO_2$ single layer, $Al_2O_3/TiO_2$ double layer and $Al_2O_3/TiO_2/Al_2O_3/TiO_2$ multilayer were studied for enhancement of water vapor barrier properties. After thin film water vapor barrier deposited on PES substrate and $SnO_x$-based TFT, thin film permeation characteristics were three orders of magnitude smaller than that without water vapor barrier layer of PES substrate, stability of $SnO_x$-based TFT devices were significantly improved. Therefore, the results indicate that $Al_2O_3/TiO_2$ water vapor barrier layers are highly proper for use as a passivation layer in $SnO_x$-based TFT devices.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.147-155
• /
• 1996

Optical properties of $TiO_2/M/Ag/M/TiO_2$ films have been changed with the diffusion barrier metal M. Optimum opticla properties of $TiO_2/M/Ag/M/TiO_2$ as the transparent heat mirror film, could be obtained with Ti among diffusion barrier metals of Ti, Cu, Zr and Al. $TiO_2/M/Ag/M/TiO_2$ film, which was fabricated by sputtering of 18 nm-thick $TiO_2$ and Ag, and 4nm-thick Ti, showed maximum transimittance of 89% at visible wavelength and infrared reflectance of 97% at wavelength of 3000 nm. Optical properties of this film was not degraded by Xenon-sunshine weather test for 240 hours. For specimens with barrier layers of Cu, Zr, and Al, degradation of optical properties by weather test was increased in a sequence of films with Cu, Zr, and Al barrier layers.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.106-111
• /
• 2005

Failure mechanisms were investigated for the two layer thermal barrier coatings consisting of NiCrAlY bond coat and $ZrO_2-8wt.\% Y_{2}O_3$ ceramic coating during cyclic oxidation. $Al_{2}O_3$ developed at the ceramic coating/bond coat interface first, followed by the Cr/Ni rich oxides such as $NiCr_{2}O_4 and Ni(Al,Cr)_{2}O_4$ during cyclic oxidation It was observed that the spalling of ceramic coatings took place primarily within the NiCrAlY bond coat oxidation products or at the interface between the bond coat oxidation products and zirconia based ceramic coating or the bond coat. It was also observed that the fracture within these oxidation products occurred with the formation of $Ni(Cr,Al)_{2}O_4$ spinel or Cr/Ni rich oxides. It was therefore concluded that the formation of these oxides was a life-limiting event for the thermal barrier coatings.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.340-344
• /
• 1998

Failure mechanisms were investigated for the two layer thermal barrier coatings consisting of NiCrAlY bond coat and $ZrO_2$-8wt.% $Y_2O_3$ ceramic coating during cyclic oxidation. $Al_2O_3$ developed at the ceramic coating/bond coat interface first, followed by the Cr/Ni rich oxides such as $NiCr_2O_4$ and $Ni(Al, Cr)_2O_4$ during cyclic oxidation. It was observed that the spalling of ceramic coatings took place primarily within the NiCrAlY bond coat oxidation products or at the interface between the bond coat oxidation products and zirconia based ceramic coating or the bond coat. It was also observed that the fracture within these oxidation products occurred with the formation of $Ni(Cr, Al)_2O_4$ spinel or Cr/Ni rich oxides. It was therefore concluded that the formation of these oxides was a life-limiting event for the thermal barrier coatings.

• Korean Journal of Materials Research
• /
• v.12 no.3
• /
• pp.200-204
• /
• 2002

We fabricated TMR devices which have double oxidized tunnel barrier using plasma oxidation method to form homogeneously oxidized AlO tunnel barrier. We sputtered 10 $\AA$-bottom Al layer and oxidized it by varying oxidation time for 5, 10, 20 sec. Subsequent sputtering of 13 $\AA$ - Al was performed and the matallic layer was oxidized for 120 sec. The electrical resistance changed from 700$\Omega$ to 2700$\Omega$ with increase of oxidation time, while variation of MR ratio was little spreading 27~31% which is larger than that of TMR device of ordinary single tunnel barrier. We calculated effective barrier height and width by measuring I-V curves, from which we found the barrier height was 1.3~1.5 eV, sufficient for tunnel barrier, and the barrier width(<16.2 $\AA$) was smaller than that of directly measured value by the tunneling electron microscopy. Our results may be caused by insufficient oxidation of Al precursor into $Al_2O_3$. However, double oxidized tunnel barriers were superior to conventional single tunnel barrier in uniformity and density. We found that the external magnetic field to switch spin direction of ferromagnetic layer of pinned layer breaking ferro-antiferro exchange coupling was increased as bottom layer oxidation time increased. Our results imply that we were able to improve MR ratio and tune switching field by employing double oxidized tunnel barrier process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.344-344
• /
• 2010

A capacitor with engineered tunnel barrier composed of High-k materials has been fabricated. Variable oxide thickness (VARIOT) barrier consisting of thin SiO2/HfO2/Al2O3 (2/1/3 nm) dielectric layers were used as engineered tunneling barrier. We studied the electrical characteristics of multi stacked tunnel layers for various RTA (Rapid Thermal Anneal) and FGA (Forming Gas Anneal) temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.129-130
• /
• 2009

The P/E characteristics of $HfO_2$ CTF memory capacitor with $SiO_2/HfO_2/Al_2O_3$(OHA) engineered tunnel barrier were investigated. After a growth of thermal oxide with a thickness of 2 nm, 1 nm $HfO_2$ and 3 $Al_2O_3$ layers were deposited by atomic layer deposition (ALD) system. The band offset was calculated by analysis of conduction mechanisms through Fowler-Nordheim (FN) plot and Direct Tunneling (DT) plot. Moreover the PIE characteristics of $HfO_2$ CTF memory capacitor with OHA tunnel barrier was presented.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.11-14
• /
• 2022

In this work, we evaluated the Al₂O₃ film, which was deposited by atomic layer deposition, degraded by exposure to harsh environments. The Al₂O₃ films deposited by atomic layer deposition have long been used as a gas diffusion barrier that satisfies barrier requirements for device reliability. To investigate the barrier and mechanical performance of the Al₂O₃ film with increasing temperature and relative humidity, the properties of the degraded Al₂O₃ film exposed to the harsh environment were evaluated using electrical calcium test and tensile test. As a result, the water vapor transmission rate of Al₂O₃ films stored in harsh environments has fallen to a level that is difficult to utilize as a barrier film. Through water vapor transmission rate measurements, it can be seen that the water vapor transmission rate changes can be significant, and the environment-induced degradation is fatal to the Al₂O₃ thin films. In addition, the surface roughness and porosity of the degraded Al₂O₃ are significantly increased as the environment becomes severer. the degradation of elongation is caused by the stress concentration at valleys of rough surface and pores generated by the harsh environment. Becaused the harsh envronment-induced degradation convert amorphous Al₂O₃ to crystalline structure, these encapsulation properties of the Al₂O₃ film was easily degraded.