• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.986-991
• /
• 2018

In this paper, an A/D conversion module was designed and fabricated to improve the dynamic range of wideband digital receivers. The A/D conversion module for expanding the dynamic range converts signals into a digital signal by branching the input signal into the normal path and the amplification path according to the input signal level. Test results of the fabricated module show that the normal path of the A/D conversion module converts an input level of -57 dBm to -12 dBm into a digital signal, and the amplification path converts an input level of -30 dBm to +12 dBm into a digital signal without distortion. This translates to an input dynamic range characteristic of 69 dB. Moreover, it is confirmed that the constant output characteristic is exhibited at an instantaneous bandwidth of 100 MHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10C
• /
• pp.982-989
• /
• 2007

In this paper, we propose a 3DTV system that considers user's view point and display environment. The proposed system consists of 3 parts - multi-view encoder/decoder, face-tracker, and 2D/3D converter. The proposed system try to encode multi-view sequence and decode it in accordance with the user's view point and it also gives a stereopsis to the multi-view image by using of 2D/3D conversion which converts decoded two-dimensional(2D) image to three-dimensional(3D) image. Experimental results shows that we are able to correctly reconstruct a stereoscopic view that is exactly corresponding to user's view point.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1031-1038
• /
• 2005

In this paper, we propose real-time 3D image converting architecture by a unit of pixel for 2D/3D compatible PC and LCD of cellular phone with parallax burier, and implement a system for overall display operation after designing a circuit based on FPGA. After digitizing anolog image signal from PC, we recompose it to 3D image signal according to input image type. Since the architecture which rearranges 2D image to 3D depends on parallax burier, we use interleaving method which mixes pixels by a unit of R, G, and B cell. The propose architecture is designed into a circuit based on FPGA with high-speed memory access technique and use 4 SDRAMs for high performance data storing and processing. The implemented system consists of A/D converting system, FPGA system to formatting 2D signal to 3D, and LCD panel with parallax barrier, for 3D display.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2016.10a
• /
• pp.68-70
• /
• 2016

3D 프린터는 연속적인 계층에 특수한 재료를 출력시켜 3차원 물체를 만들어 내는 장치이다. 3D 프린팅을 위해서는 3D 모델을 생성한 후, 이를 3D 프린터에 출력할 수 있도록 G-code로 변환해야 한다. 본 논문에서는 이 변환 작업을 완전 분산 방식으로 처리할 수 있는 알고리즘을 제안한다. 이를 위해 하나의 메인 노드와 N개의 작업 노드로 구성한 시스템에서 2단계에 걸쳐 분할 정복(divide-and-conquer) 방식으로 변환하도록 하였다. 실제 구현한 시스템을 이용하여, 성능에 미치는 요소(모델의 크기 및 정밀도)에 따른 변환 시간의 단축 효과를 보였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.958-964
• /
• 2005

In this thesis, the matching network at the local oscillator port of the sub-harmonic mixer is optimized for reducing the conversion loss. A downconverter for point to point system applications is designed and fabricated using the such sub-harmonic mixer. The sub-harmonic mixer achieved the conversion loss of 11.8 dB at the 12 dBm input power of the local oscillator and the isolation of less than -40 dB. The downconverter achieved the IF output power flatness of 2 dB and the total noise figure of 5.9 dB.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.6
• /
• pp.1053-1058
• /
• 2021

This paper presents the multi-band mixer which converts a X-, K- and Ka-band adaptively by adjusting the gate-bias voltage of an active device. The proposed mixer presented a conversion loss of -10 dB at -0.8 V gate-bias voltage for X-band, a conversion loss of -9 dB at -0.3 V gate-bias voltage for K-band and for Ka-band, a conversion loss of -7 dB at -0.2 V gate-bias voltage under the LO power of +6.0 dBm. The 1dB compression point (P1dB) is +0.5 dBm for all band.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.9
• /
• pp.13-19
• /
• 1999

This paper describes a design of an 8-bit 100KSPS 1mW CMOS A/D Converter. Using a novel systematic offset cancellation technique, we reduce the systematic offset voltage of operational amplifiers. Further, a new Gain amplifier is proposed. The proposed A/D Converter is fabricated with a $0.6{\mu}m$ single-poly triple-metal n-well CMOS technology. INL and DNL is within ${\pm}1LSB$, and SNR is about 43dB at the sampling frequency of 100KHz. The power consumption is $980{\mu}W$ at +3V power supply.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2010.11a
• /
• pp.1381-1383
• /
• 2010

웹서비스는 표준 프로토콜인 HTTP를 이용하기 때문에 방화벽의 제약이 없어서 어디서나 실시간으로 통신하여야 하는 모니터링 시스템 특성상 꼭 필요한 기술이다. 또한, XML로 기술된 SOAP 메시지는 플랫폼 독립적이고, 시스템 확장과 통합에 유리하다. 본 논문에서 구현한 웹모니터링 시스템은 웹서비스를 이용하여 설치가 용이하고, 인터넷을 통해 원격지의 태양광 발전 시스템을 관리, 감시하는데 제약이 없으며, 신재생에너지 산업 통합에 적용될 수 있다.

• Proceedings of the ESK Conference
• /
• 1993.10a
• /
• pp.236-242
• /
• 1993

소비자들이 원하는 제품의 감성을 언어로 표현하여 줄 때, 이를 퍼지추론하여 칼라를 선택해주는 시스템을 개발하였다. 시스템은 감성언어입력, 감성언어퍼지화, 칼라추론, 추론규칙, 출력 등 모두 5개 의 모듈로 구성되어 있다. 시스템은 감성언어를 색상, 채도, 명도로 변환시킨 후 이를 다시 R, G, B 값으로 변환시키게 된다. 이때, 색상, 채도, 명도로의 변환에는 퍼지화규칙이 사용되게 되며, R,G,B 값으로의 변환 에는 칼라추론규칙이 사용되게 된다. 퍼지화규칙을 만들기 위해 S.D.(의미미분)법에 의한 감성언어의 요인 분석을 실시하였으며, 동시에 문헌조사를 통해 얻은 칼라와 관련한 감성정보를 if-then 규칙 형태로 시스템에 구현하였다.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 1996.06a
• /
• pp.79-109
• /
• 1996

In order to transform the underground utility data into the 3-D spatial objects, this thesis defined the type of the 3-D spatial objects and the storage structure of objects, and developed the spatial data transformation system that transforms the 2-D underground utility data into the pre-defined 3-D spatial objects through the Booch Method, an object-oriented development method. For this sake, the relational data model of ARC/INFO and the storage structure are analyzed, as well as the pre-requisites, required for the 3-D visualization of the underground utilities. Also, the 2-D underground utility data, saved in ARC/INFO, were transformed into the ASCII files through the internal pre-processing procedure, then used as the input data of the transformation system. In addition, to develop the transformation system, the object-oriented development methods are studied first and, then, applied to the system analysis and the design procedure with the Booch Method as a development method. Finally, the results of analysis and design procesure are implemented through AML, a ARC/INFO macro language, and C++, an object-oriented programing language. As a result of this study, the 3-D spatial objects that can visualize the 2-D utilities in 3-D, are acquired, and the adaptation of object-oriented development method to the system development procedure enabled an effective development prodedure.