• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.3
• /
• pp.23-30
• /
• 2012

In this paper, we propose a new near-field reader antenna for 900 MHz RFID. The proposed antenna consists the micro-strip antenna with the periodic structure. The overall dimension of the antenna is $313mm{\times}152mm{\times}14mm$. The antenna has the uniform E-field distribution in near field region and the heart-shaped radiation beam pattern (Peak gain=-2 dBi). The transmitted power range is from 17 dBm to 23 dBm. We focus on minimizing the detected error by suppressing the reflected power from the metal, which is attached to the surface by tag, and by reducing the transmitted power from tag.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.642-646
• /
• 2016

A wearable antenna made using conductive tape on paper is presented in this paper. The proposed antenna is composed of a half-wavelength conducting dipole strip and a parasitic conducting strip on the A4 copy paper. The antenna is fed at the center of the dipole strip by an SMA connector. The configuration of the proposed antenna changes according to the origami method. Therefore the radiation patterns of the antenna vary according to whether or not the paper is folded. This approach solves the problem that the reception ratio of the signal decreases because of null points in the antenna radiation pattern. The reflection coefficient and the radiation pattern of the proposed antenna at 900 MHz are evaluated using an EM simulation and measurements. It was shown that the proposed paper antenna has reconfigurable characteristics at 900 MHz when utilizing the origami method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.9-18
• /
• 2006

This paper presents a Monte-Carlo based method to obtain a probability of interference in the 900MHz passive RFID systems. We show an efficient algorithm to calculate not only in-band interference due to unwanted emission of interfering sources for a given emission mask, but out-of-band interference, which depends on the blocking performances of a victim receiver filter. We next apply the proposed method to two types of RFID systems, one is to use simple FHSS and the other to adopt a hybrid use of FHSS and LBT, which senses the channel before transmission. Simulation is first performed with a SEAMCAT. We next make simulation with a MATLAB software which implements SEAMCAT algorithm and show both results from two softwares are similar.

• Journal of Internet Computing and Services
• /
• v.8 no.4
• /
• pp.51-59
• /
• 2007

This paper presents the development of RFID educational system based on using 900MHz air interface between the reader and the active tag. The software of reader and the active tag is developed on embedded environment, and the software of PC controlling the reader is based on window OS operated as the server. The AT89C51ED2 VLSI chip is used for the processor of the reader and the active tag. As the development environment, Keil compiler is used for the reader and the active tag of which the programing language is C. The visual C language of the visual studio on the PC activated as the server is used for development language. To verify the function of the system, PC gets the tag's identification number through the reader and send the data to with the active tag memory a certain contents as "wite" operation. Finally the data written from the active tag's memory is sent to the PC via the reader as "read" operation and compare the received data with one already sent to the tag.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.10
• /
• pp.1240-1247
• /
• 2019

In this paper, we designed a four-band antenna that can be applied to WLAN and WiMAX systems by designing a microstrip feeding structure, four branch lines and a slit on the ground plane. The proposed antenna is designed with a size of 16.0 mm (W1) × 48.0 mm (L8) on a dielectric substrate of 18.0 mm (W) × 50.0 mm (L) × 1.0 mm(h). and a slit of 2.9 mm (W7) × 4.0 mm (L7) is inserted into the ground plane of 18.0 mm (W) × 18.7 mm (L6). Based on -10 dB production and measurement results, it obtained 60.8 MHz (8,730~9,338 MHz), 310 MHz (2.33~2.64 GHz) in the 2.4 GHz band, 420MHz (3.39~3.81 GHz) in the 3.4 GHz band, and 2,070 MHz (4.62~6.69 GHz) in the 5.0 GHz. In addition, the gain and radiation pattern characteristics of the quadrant band are measured from the measurement results anechoic chamber.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.1
• /
• pp.58-65
• /
• 2013

It's introduced a BLA(Branch Loop Antenna) that is modified from conventional loop, and verified antenna performances for applying to mobile handset. Branch elements are added to a rectangular loop, and low resonance is obtained by the length of the branch line. When resonance frequency of a single loop is 2.5GHz, BLA had near 900 MHz under the same antenna size. Multiple resonances are established by the locations of branch connection and their lengths. By the implementation and measurement for the dual band BLA, it's showed 75MHz -10dB bandwidth and -3.03~-1.46dBi average gains with 49.73~71.39% efficiencies at GSM900 band, and 90MHz -6dB bandwidth and -8.14~-2.17dBi average gains with 15.34~60.62% efficiencies at DCS1900 band. And H-plane radiation patterns were omni-directional. These performances are good for the mobile handset antenna.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.6C
• /
• pp.619-624
• /
• 2002

In this paper, a novel architecture of programmable divider with fifty percent duty cycle output and programmable dividing number has been proposed. Through HSPICE simulation, a 900MHz frequency synthesizer with proposed (sequency divider has designed in a standard 0.25㎛ CMOS technology To verify the operation of proposed frequency divider, a chip had been fabricated using 0.65㎛ 2-poly, 3-metal standard CMOS processing and experimental result shows that the proposed frequency divider works well. The designed voltage controlled oscillator(VCO) has a center frequency of 900MHz a tuning range of $\pm$10%, and a gain of 154HHz/V. The simulated frequency synthesizer performance has a settling time of 1.5$\mu$s, a frequency range from 820MHz to IGHz and power consumption of 70mW at 2.5V power supply voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.563-568
• /
• 2007

In this paper, the proposed package antenna, which is meander line structure with short pin, is miniaturized to realize RF-SoP at 900 MHz RFID band. The RFID BGA(Ball Grid Array) chip is put in a cavity of LTCC Layers. The coupling and cross talk, which are happen between BGA chip and proposed package antenna, are reduced by faraday cage, which consists of ground and via fences, is realized to enhance the isolation between BGA chip and antenna. The proposed antenna structure is focused on the package level antenna realization at low frequency band. The novel proposed package antenna size is $13mm{\times}9mm{\times}3.51mm$. The measured resonance frequency is 0.893 GHz. The impedance bandwidth is 9 MHz. The maximum gain of radiation pattern is -2.36 dBi.

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.109-110
• /
• 2008

본 논문에서는 900MHz RFID 수동형 태그 전치부를 설계하고 검증하였다. 문턱전압(threshold voltage) 제거 구조의 전압 체배기, 전류를 이용한 복조 회로로 설계되었으며 파워다운 회로를 추가하여 정류동작의 안정성에 중점을 두었다. PWM(Pulse Width Modulation)을 이용한 변조기를 구조로 입력단에 용량성 임피던스의 변화로 변조 동작을 검증하였다. 삼성 0.18um 공정을 이용하였고, 인식거리는 15m, 평균 소모 전력은 약 60uW이며, 패드를 포함한 칩 사이즈는 $1.22mm^2$이다.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.205-207
• /
• 2006

In this paper, we present a design procedure of high linearity LNA using CMOS technology. To enhance the low linearity of the inherent CMOS transistor, we adopt the modified derivate superposition with adding external capacitor. The simulation of the designed LNA shows $IIP_3$ of +12-dBm, power gain of 13.8-dB, noise figure of 1.75-dB over the 900 MHz UHF RFID frequencies. The circuit draws the current of 4.2 mA from 1.8-V supply voltage.