• Journal of the Korean Vacuum Society
• /
• v.22 no.2
• /
• pp.66-78
• /
• 2013

In order to develop of 80 kW RF plasma torch system, we achieved three-dimensional simulations for the extraction of more information as temperature in torch and fluid behavior analysis, etc. The position of powder injection tube, the plasma discharge characteristics with various input current and various length of ceramic tube, and the plasma temperature characteristics with process gas flow rate such those was simulated. RF thermal plasma torch designed by simulation was manufactured that was measured to the maximum of 89.3 kW power. The mass production using developed 80 kW RF thermal plasma torch system were investigated by characteristics manufactured of Si nano powder. The mass-production level of Si nano-powder was average of 539 g/hr and high yield rate of 71.6%, respectively. The particle size distribution $D_{99}/D_{50}$ of manufacturing nano-powder was investigated to 1.98 as a good uniform.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.67-67
• /
• 2011

Pulsed DC $BCl_3/SF_6$ 플라즈마를 사용하여 GaAs와 AlGaAs의 건식 식각을 연구하였다. 식각 공정 변수는 가스 유량 (50~100 % $BCl_3$ in $BCl_3/SF_6$), 펄스 파워 (450~600 V), 펄스 주파수 (100~250 KHz), 리버스 시간 (0.4~1.2 ${\mu}s$)이었다. 식각 공정 후 표면 단차 측정기 (Surface profiler)를 사용하여 표면의 단차와 거칠기를 분석하였다. 그 결과를 이용하여 식각률 (Etch rate), 표면거칠기 (Surface roughness), 식각 선택비 (Selectivity)와 같은 특성 평가를 하였다. 실험 후 주사 현미경 (FE-SEM, Field Emission Scanning Electron Microscopy)을 이용, 식각 후 시료의 단면과 표면을 관찰하였다. 실험 결과에 의하면 1) 18 sccm $BCl_3$ / 2 sccm $SF_6$, 500 V (Pulsed DC voltage), 0.7 ${\mu}s$ (Reverse time), 200 KHz (Pulsed DC frequency), 공정 압력이 100 mTorr인 조건에서 GaAs와 Al0.2Ga0.8As의 식각 선택비가 약 48:1로 우수한 결과를 나타내었다. 2) 펄스 파워 (Pulsed DC voltage), 리버스 시간(Reverse time), 펄스 주파수(Pulsed DC frequency)의 증가에 따라 각각 500~550 V, 0.7~1.0 ${\mu}s$, 그리고 200~250 KHz 구간에서 AlGaAs에 대한 GaAs의 선택비가 감소하게 되는 것을 알 수 있었다. 이는 척 (chuck)에 인가되는 전류와 파워를 증가시키고, 따라서 GaAs의 식각률이 크게 증가했지만 AlGaAs 또한 식각률이 증가하게 되면서 GaAs에 대한 식각 선택비가 감소한 것으로 생각된다. 3) 표면 단차 측정기와 주사전자현미경 사진 결과에서는 GaAs의 경우 10% $SF_6$ (18 sccm $BCl_3$ / 2 sccm $SF_6$)가 혼합된 조건에서 상당히 매끈한 표면 (RMS roughness < 1.0 nm)과 높은 식각률 (~0.35 ${\mu}m$/min), 수직의 식각 측벽 확보에서 매우 좋은 결과를 보여주었다. 또한 같은 공정 조건에서 AlGaAs는 식각이 거의 되지 않은 결과 (~0.03 ${\mu}m$/min)를 보여주었다. 위의 결과들을 종합해 볼 때 Pulsed DC $BCl_3/SF_6$ 플라즈마는 GaAs와 AlGaAs의 선택적 식각 공정에서 매우 우수한 공정 결과를 나타내었다.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.471-475
• /
• 2006

$VO_x$ thin films with the thickness of 450 nm were prepared on a $Pt/Ti/SiO_{2}/Si$ substrate at room temperature by a reactive radio frequency (rf) magnetron sputtering method. The deposition rates of $VO_x$ thin films were investigated as a function of $O_{2}$ concentration and rf power. As the $O_{2}$ concentration in a $O_{2}/Ar$ mixture increased, the deposition rate decreased. However, the deposition rate increased with increasing rf power. The deposited $VO_x$ thin films were annealed at $450^{\circ}C$ for 2, 4, and 6 h in $O_{2}$ and $N_{2}$ ambient. After annealing, the phase changes of $VO_x$ thin films were investigated using X-ray diffraction analysis. The plane and cross-sectional views of $VO_x$ thin films before and after annealing were observed by field emission scanning electron microscopy. The metal-insulator transition (MIT) properties of $VO_x$ thin films were measured using current-voltage measurement. The excellent MIT properties were observed in $VO_x$ thin films annealed in $O_{2}$ ambient.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.338-345
• /
• 2015

Poly(phenylene oxide) (PPO) and polyether imide (PEI) were sulfonated and aminated to create sulfonated poly(phenylene oxide) (SPPO) and aminated polyether imide (APEI), respectively. Characterization of the SPPO and APEI were performed via measurements of FTIR, thermogravimetry (TGA), swelling degree, ion exchange capacity (IEC), and ion conductivity. Next, the surfaces of these membranes were modified by surface fluorination at room temperature. The surface fluorinated SPPO and APEI membranes underwent characterization again for the mentioned measurements to determine any differences. The 3 types of bi-polar membranes were prepared by varying the IEC of the APEI at a fixed SPPO IEC value, which were applied to the low and high NaCl concentration of feed solution at the different current density, respectively. The hypochlorite concentration derived from the surface fluorinated membranes was dependent on the IEC of the APEI and ranged from 491 to 692 ppm at $80mA/m^2$. At low current density of $5mA/m^2$, the hypochlorite concentrations ranged from 18 to 28 ppm for the 4 hrs surface fluorinated membranes and their durability increased greatly.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.128-128
• /
• 2011

본 연구에서는 자동유량측정시설에 의하여 실시간으로 생산되는 자동유량측정 자료의 정상성 여부를 판단하는데 중요한 적정 측정 신뢰구간을 실시간으로 예측할 수 있는 기술을 개발하였다. 전세계적으로, 현대적인 유량측정이 시작된 이래 연속유량 산정을 위한 방법은 수위-유량관계곡선을 이용하는 방법 외에 실무적으로 활용 가능한 방법은 거의 전무한 실정이다. 수위-유량관계곡선을 이용하는 방법은 연속수위를 계측하여 이에 해당하는 연속유량을 산정하는 방법으로 수위와 유량간에 일정한 관계를 가지는 정상적인 흐름을 보이는 자연하천의 경우에 정확도가 매우 높다. 그러나 감조나 구조물 등에 의해 유량이 조절되는 경우에 유량산정의 정확도는 현저히 떨어지게 된다. 따라서 수위에서 유량을 환산하는 방법이 아닌 유량을 직접 연속으로 측정하는 방법이 꾸준히 연구되어 왔고, 이 중 가장 대표적인 방법이 자동유량측정 방법이다. 그러나 자동유량측정 방법은 유량을 연속으로 측정할 수 있다는 장점에 반해 측정된 유량의 정확도를 높이기가 매우 어렵다는 단점도 가지고 있다. 계측 자체의 기술적 한계는 주로 계측기기적인 문제로 이는 전자기, 통신 기술 등 첨단 기술의 발전과 함께 다양한 현장 시험을 통해 폭넓은 개선이 이루어지고 있다. 그러나 아직 기술적 완성도가 완전하지 못한 현실에서, 현재 설치되어 있는 자동유량측정 유량자료의 신뢰도를 높이기 위해서는 각각의 계측 시점에서 자료가 정상적으로 산정되고 있는지에 대한 검정이 필요하고, 이는 자동유량측정 자료의 정확도 확보에 매우 중요한 관건으로 작용할 수밖에 없다. 이러한 배경에서 본 연구에서는 조석성분과 유출성분을 분리하여 예측하는 방법을 새롭게 개발 적용하였다. 자료는 자료의 시간해상도 증감에 따른 실제 예측의 정확도 증감을 고려하여 가장 적절하다고 판단되는 시자료를 사용하였으며, 자료간 상관을 분석하여 주 입력 자료로 팔당댐 방류량, 한강대교 지점 수위, 전류 수위를 이용하였다. 모형의 예측 능력을 극대화하기 위하여 조석 영향을 받는 자료의 경우는 웨이블릿 변환(wavelet transform)을 이용하여 순수 유출성분과 조위성분을 분리하여 별도로 적용하였다. 그리고 예측을 위한 모형은 실시간 자료기반 모형으로 그 안정성이 인정된 서포트벡터머신(support vector machine)을 이용하였다. 이러한 과정을 통해 한강대교 지점의 순수 유출성분과 조위성분의 유량을 각각 예측한 후 두 결과를 합성하여 최종 한강 대교 지점의 유량을 산정하였다. 조석성분을 분리하여 한강대교 지점의 유량을 예측한 결과 대부분의 예측치가 95% 예측구간에 포함되었다. 그리고 조석성분을 분리하지 않은 모형과 조석성분을 분리한 모형의 예측 능력을 비교한 결과, 조석성분을 분리한 모형이 예측이 정확도가 높았다. RMSE의 경우 분리하지 않은 모형대비 23%의 예측오차가 감소하였고, NSC의 경우 0.92에서 0.95로 예측의 정확도가 증가하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.184-191
• /
• 2023

With increasing corrosion in RC (Reinforced Concrete) structures, cracks occurred due to corrosion products and bearing load resistance decreased. In this study, corrosion was induced through an accelerated corrosion test (ICM: Impressed Current Method) with 140 hours of duration, and changes in USV (Ultra-Sonic Velocity), flexural failure load, and corrosion weight were evaluated before and after corrosion test. Three levels of cover depth (20 mm, 30 mm, and 40 mm) were considered, and the initial cracking period increased and the rust around steel decreased with increasing cover depth. In addition, the USV linearly decreased with decreasing cover depth and increasing amount of corrosion. In the flexural loading test, the bending capacity decreased by more than 10% due to corrosion, but a clear correlation could not be obtained since the corrosion ratio was small, so that the effect of slip was greater than that of reduced cross-sectional area of steel due to corrosion. As cover depth increased, the produced corrosion amount and USV changed with a clear linear relationship, and the cracking period due to corrosion could be estimated by the gradient of the measured corrosion current.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.4
• /
• pp.135-140
• /
• 2024

It is said that PV power generation systems have a long lifespan compared to other renewable energy sources and require little maintenance. However, there are cases where the performance expected during initial design is not achieved due to shading, temperature rise, mismatch, contamination/deterioration of PV modules, failure of inverter, leakage current, and arc generation. Therefore, in order to solve the problems of these systems, the power generation amount and operation status are investigated qualitatively, or the performance is comparatively analyzed based on the performance ratio (PR), which is the performance index of the solar power generation system. However, because it includes large losses, it is difficult to accurately determine whether there are any abnormalities such as performance degradation, failure, or defects in the PV power generation system using only the performance coefficient. In this paper, we studied a status diagnosis algorithm for shading, inverter failure, leakage, and arcing of PV modules to optimize the power generation of PV power generation systems according to changes in the surrounding environment. In addition, using the studied algorithm, we examined the results of an empirical test on condition diagnosis for each area and the resulting optimized operation of power generation.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.11
• /
• pp.140-149
• /
• 1996

Cursive characters are written on an economical principle to reduce the motion of a pen in the limit of distinction between characters. That is, the pen is not lifted up to move for writing a next stroke, the pen is not moved at all, or connected two strokes chance their shapes to a similar and simple shape which is easy to be written. For these reasons, strokes and korean alphabets are not only easy to be changed, but also difficult to be splitted. In this paper, we propose a curvature stroke modeling method for splitting and matching by using a structural primitive. A curvature stroke is defined as a substroke which does not change its curvanture. Input strokes handwritten in a cursive style are splitted into a sequence of curvature strokes by segmenting the points which change the direction of rotation, which occur a sudden change of direction, and which occur an excessive rotation Each reference of korean alphabets is handwritten in a printed style and is saved as a sequence of curvature strikes which is generated by splitting process. And merging process is used to generate various sequences of curvature strikes for matching. Here, it is also considered that imaginary strokes can be written or omitted. By using a curvature stroke as a unit of recognition, redundant splitting points in input characters are effectively reduced and exact matching is possible by generating a reference curvature stroke, which consists of the parts of adjacent two korean alphasbets, even when the connecting points between korean alphabets are not splitted. The results showed 83.6% as recognition rate of the first candidate and 0.99sec./character (CPU clock:66MHz) as processing time.

• Journal of Korea Water Resources Association
• /
• v.40 no.9
• /
• pp.697-707
• /
• 2007

In this study, we estimated the PMP(Probable Maximum Precipitation) and its transition in case of the typhoon Rusa which happened the biggest damage of all typhoons in the Korea. Specially, we analysed the moisture maximizing rate under the consideration of meteorological condition based on the orographic property when it hits in Gangneung region. The PMP is calculated by the rate of the maximum persisting 12 hours 1000 hPa dew points and representative persisting 12 hours 1000 hPa dew point. The former is influenced by the moisture inflow regions. These regions are determined by the surface wind direction, 850 hPa moisture flux and streamline, which are the critically different aspects compared to that of previous study. The latter is calculated using statistics program (FARD2002) provided by NIDP(National Institute for Disaster Prevention). In this program, the dew point is calculated by reappearance period 50-year frequency analysis from 5% of the level of significant when probability distribution type is applied extreme type I (Gumbel distribution) and parameter estimation method is used the Moment method. So this study indicated for small basin$(3.76km^2)$ the difference the PMP through new method and through existing result of established storm transposition and DAD(Depth-Area-Duration). Consequently, the moisture maximizing rate is calculated in the moisture inflow regions determined by meteorological fields is higher $0.20{\sim}0.40$ range than that of previous study. And the precipitation is increased $16{\sim}31%$ when this rate is applied for calculation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.