• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.51-55
• /
• 1995

본 연구에서는 회전동력전달계의 진동특성을 해석하고 이를 설계자료로 이용하기 위하여, 계 전체의 유효강성행렬 (effective stiffness matrix)을 실험적으로 결정할 수 있는 방법을 제안하였다. 이것은 비교적 측정이 용인한 관성행렬이 알려져 있다고 가정한 경우 기존의 선형 모델링을 그대로 이용하고, 위의 모든 기계요소의 해석이 불가능한 강성들을 포함한 등가강성(equivalent stiffness)으로 구성된 계의 유효강성행렬을, 실험에 의해 얻어진 계의 여러 작동상황과 이에 따른 고유진동수에 매칭(matching)시켜 결정하는 것이다. 또한, 이의 검증을 위하여 유성기어와 클러치로 이루어진 가상의 동력전달계를 구성하고 이의 시뮬레이션 결과를 이용하여, 유효강성 결정법을 통해 얻어진 등가강성들과 실제값들의 비교함으로서 그 신뢰도를 추정하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.1
• /
• pp.77-84
• /
• 2011

This study is to develop nonlinear analysis algorithm for transfer matrix method, which can be applied to continuous beam analysis. Gauss-Lobatto integral rule is adopted and the transfer matrix is derived from stiffness matrix. In the transfer matrix method, the system equation has a constant number of unknowns regardless of number of D.O.F. Therefore, the transfer matrix method has computational efficiencies not only in linear elastic analysis but also in nonlinear analysis. To verify the developed method, the analysis results of several examples are compared with commercial code in moment-curvature, moment-displacement and load-displacement relation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04a
• /
• pp.608-614
• /
• 1995

공작기계 등과 같이 복잡한 대형 구조물의 구조해석에 있어서 결합부요소의 강성과 질량특성을 모델링하는 일반적 인 방법이 없는 실정이므로 어려움이많다. 본 연구에서는 공작기계에서 흔히 쓰이는 Slide-way contact joint 결 합부를 등가의 강성행렬 요소(Generalized stiffness matrix element)로 모델링하는 방법을 제안하였다.. 기존의 유 한용소 해석법 프로그램을 이용하여 결합부 유한요소 모델의 유연도계수(Flexibility influence coefficients)를 계산하고 Guyan의 정축약이론을 이용하여 등가의 강성행렬요소로 축약시키는 방법이다. 제안된 방법을 대형 평면연 삭기 구조해석에 적용하고, 그 결과를 강결합 모델의 결과 및 Yoshimura의 등가스프링결합부 모델을 사용한 경우의 결과와 비교하므로써 본 연구에서 제안한 결합부 모델링 방법의 유용성을 확인하였다.

• Composites Research
• /
• v.17 no.2
• /
• pp.9-14
• /
• 2004

In this study, analytical investigations on the flexural behavior of FRP reinforced concrete slab were discussed. In the derivation of analytic solution, the FRP reinforced concrete slab was modeled as a structural orthotropic plate. To determine the flexural rigidities of an orthotropic plate model, the elastic equivalence method was employed. In the finite element analysis, the approximate method to determine the rigidity matrix of orthotropic plate element was also suggested using the elastic equivalence method. The results obtained by the analytical solution and the finite element analysis were compared with that of experiment.

• Journal of KSNVE
• /
• v.7 no.4
• /
• pp.571-578
• /
• 1997

Recently, many general-purpose packages for fluid-structure interaction problems have been announced. However, they have a lot of limitations to model structures in the fluid-structure interaction problems reasonably. Utilizing general-purpose packages such as MSC/NASTRAN and SYSNOISE, in this paper, a method to slove the radiation scattering problems with some accuracy in the fluid-structure interaction problems was developed. Using a simple model, the results from the presented method here are compared with those from SYSNOISE. The result shows quite a good agreement between the two methods. The problems, which could not be solved by SYSNOISE, were tried to solve with the presented method and results were presented. It was proved that this method could be safely used to solve fluid-structure interaction problems.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.10
• /
• pp.226-232
• /
• 2003

Difficulties in the finite element modeling of human spine are evaded by using a stiffness matrix element whose properties can be characterized from experimentally measured stiffness of functional spinal units. Relative easiness is in that inter-vertebral discs, ligaments, and soft tissues connecting vertebrae do not need to be modeled as they are. The remarkable coupling effect between distinct degrees of freedom induced by the geometric complexity can be accommodated without much effort. An idealized block model with simple geometry for vertebra is employed to assess the feasibility of this method. Analyses are performed in both levels of motion segment and spinal column, and the result is compared with that from detail model. As far as the global behavior of spine is concerned, the simplification is found not to aggravate inaccuracy only if sufficient experimental data is provided and interpreted properly.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.12
• /
• pp.1243-1249
• /
• 2012

Finite element models are updated in two stages in this paper. In the first stage, damping is neglected, and mass and stiffness matrices of a finite element model are updated using an optimization technique. The objective function for optimization consists of natural frequencies and mode shapes obtained from experimental modal testing data and finite element analysis. In the second stage, damping is considered with the mass and stiffness matrices fixed. A damping matrix is estimated assuming a proportional damping system. Then the damping matrix is adjusted using an optimization process so that the difference between the analytical and measured frequency response functions becomes minimum. This procedure of model updating has been applied to a simulated system and an experimental cantilever beam.

• Composites Research
• /
• v.32 no.4
• /
• pp.191-198
• /
• 2019

The basic mechanical properties of helicopter rotor blade are important parameters for the analysis of helicopter performance. However, it is difficult to estimate these properties because the most of rotor blades consist of various materials such as composite materials and metals, etc. In this paper, the bending/torsional stiffness for composite rotor blade of unmanned helicopter were evaluated through experimental and analytical studies. In finite element analysis, the bending/torsional stiffness were evaluated through the relationship of load-displacement and element stiffness matrix. The evaluated stiffness from the measured strains and displacements in bending and torsional test agreed well with the derived results of FEA.

• Journal of KSNVE
• /
• v.8 no.1
• /
• pp.157-170
• /
• 1998

This paper proposes a new technique to formulate the finite element model of a sandwich beam by using GHM (Golla-Hughes-McTavish) internal auxiliary coordinates to account for frequency dependence. Through the use of auxiliary coordinates, the equation of motion of undamped mass and stiffness matrix form is extended to encompass viscoelastic damping matrix. However, this methods all suffer from an increase in order of the final finite element model which is undesirable in many applications. Here we propose to combine the GHM method with model reduction techniques to remove the objection of increased model order.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.1
• /
• pp.24-34
• /
• 1990

In this paper, the formulation of a new simplified finite element is made to analyze the ultimate strength of damaged tubular members subjected to combined axial force and end moment. A damaged tubular member that has the bending deformation and the local dent is modeled by beam elements. Tangent elastic stiffness matrix of a beam element which contains the effect of the geometric nonlinearity is derived by using the updated Lagrangian approach. Here the contribution of the stiffness in the dented area is neglected since its resistance against the external loads is considered to be small. A fully plastic interaction curve of the element under combined loads taking account of the local dent effect is selected as a yielding criterion at each nodal point. Also tangent elasto-plastic stiffness matrix of the element is formulated by plastic node method. Comparison with the present solution and the existing experimental results is made showing that the present method gives quite an accurate solution.