• Journal of the Korean Geotechnical Society
• /
• v.15 no.2
• /
• pp.3-16
• /
• 1999

The objective of BMP( Barge Mounted Plant) project is to construct plants on mooring floating structures at sea. To analyze the pile behavior under mooring dolphins, generally, axial or lateral behavior of soil-pile system is evaluated by using a nonlinear subgrade reaction method which models the pile as a structural element and the soil as series of nonlinear springs along the depth. As a result, load-displacement curves at pile head can be solved by finite difference method and the equivalent stiffness of bottom boundaries of dolphin structure is evaluated. In this study off-shore site investigation was performed on the marine area of Koje Island and axial and lateral load transfer curves of the ground were modeled with depth. The subgrade reaction analysis was performed for piles under axial or lateral loadings, and the required penetration depth and section of the pile were determined. Subsequently, the spring boundaries under the dolphin structure could be modeled from the calculated load-displacement curve and then the dynamic response of the dolphin structure was analyzed reasonably by considering ground conditions. The analysis considering the stiffness of the soil-pile system has resulted in larger displacement amplitudes than those for rigid foundations. Furthermore, moment distributions of the casing were dependent on the soil-pile system so that deformable foundation induces the larger moment of top section of casing and the smaller moment of pile head.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.5
• /
• pp.29-38
• /
• 2013

The G-class cement is commonly used in practice for geothermal well cementing in order to protect a steel casing that is designed to transport hot water/steam from deep subsurface to ground surface during operating a geothermal power plant. In order to maintain optimal performance of geothermal wells, physical properties of the cementing material should be satisfactory. In this paper, relevant factors (i.e., groutability, uniaxial compression strength, thermal conductivity and free fluid content) of the G-class cement were experimentally examined with consideration of various water-cement (w/c) ratios. Important findings through the experiments herein are as follows. (1) Groutability of the G-class cement increases by adding a small dose of retarder. (2) There would be a structural defect caused when the w/c ratio is kept higher in order to secure groutability. (3) Thermal conductivity of the G-class cement is small enough to prevent heat loss from hot steam or water to the outer ground formation during generating electricity. (4) The G-class cement does not form free water channel in cementing a geothermal well. (5) The Phenolphthalein indicator is applicable to the distinction of the G-class cement from the drilling mud.

• Korean Journal of Plant Resources
• /
• v.18 no.2
• /
• pp.285-301
• /
• 2005

This study was conducted to prepare systematic and efficient measures for nature conservation and management in Beomseom Island, and to clarify characteristics of distribution of plant resources in southernmost islands of Korean peninsula. The numbers of vascular plants were summarized as 164 taxa included 6 families, 13 genera, and 15 species in pteridophyta, 1 family, 1 genus, and 1 species in coniferophyta, and 59 families, 126 genera, 146 species, and 2 varieties in endospermae composed of 49 families, 97 genera, 114 species, and 1 variety in dicotyledonae and 10 families, 29 genera, 32 species, and 1 variety monocotyledonae. Unrecorded taxa of the flora of Beomseom Island were 19 taxa included 4 taxa of pteridophyta, i.e. Hypolepis punctata, Cyrtomium fortunei, Dryopteris pacifica, and Thelypteris granduligera, 6 taxa of monocotyledonae, i.e. Setaria viridis, Zizania latifolia, Scirpus triangulatus, Zantedeschia aethiopica, Spirodela polyrhiza, and Dioscorea nipponica, and 9 taxa of dicotyledonae, i.e. Alnus firma, Boehmeria Platanifolia, Aconogonum ajanense, Phytolacca americana, Melandryum oldhamianum var. roseum, Vitis flexuosa, Clerodendron trichotomum, Elaeagnus glabra, and Siegesbeckia glabrescens. The two rare species, Osmanthus insularis that distributed only Jeju-do and Geomoondo Island and Orostachys iwarenge that distributed only southern parts of Jeju-do in Korea were investigated. The numbers of naturalized plants were 20 families, 33 genera, 34 species, and 1 variety.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.1
• /
• pp.96-103
• /
• 2006

Alaska pollock roe is mainly used as the production salted instead of salt-seasoned seafood (Myungranjeot). Alaska pollock roes with broken egg membrane are usually discarded as a waste product. In order to utilize the broken roes of Alaska pollock, imitated fish sausage was manufactured for commercial production. Hardness, cohesiveness, elasticity, brittleness, and gumminess of Alaka pollock roe sausage were evaluated based on mixture design and regression models. The higher amounts of carrageenan and tile lower amounts of starch caused the higher the texture intensity of Alaska pollock roe sausage. The pHs of control, vacuum and $N_2$ packages, increased up to 6.28, 6.23 and 6.24, respectively, during 4 months storage and then decreased. The values of volatile basic nitrogen (VBN), thiobarbituric acid (TBA), and total viable cell counts increased during storage periods, while the parameters were higher in control than in vacuum and Na packages. Coliform bacteria was not detected in all treatments during storage periods.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1005-1011
• /
• 2016

The fundamental reason for gear noise is transmission error. Transmission error occurs because of STE (static transmission error) and DTE (dynamic transmission error), while a pair of gears is meshing. These errors are generated by the deflection of the teeth and the friction on the surface of the teeth. In addition, the vibration generated by transmission error leads to excited bearings. The bearings support the shafts, and the noise is radiated after exciting the gear casing. The analysis of the contact stress in helical gear tooth flanks indicates that it is due to impact loading, such as the sudden engagement and disengagement of a gear. Stress analysis is performed for different roll positions, in order to determine the most critical roll angle. Dynamic analysis is performed on this critical roll position, in order to evaluate variation in stresses and tooth contact force, with respect to time. In this study, transmission error analysis was implemented on a spur and helical gear with involute geometry and a modified geometry profile. In addition, in order to evaluate the intensity of impact due to sudden engagement and significant backlash, the impact factor was calculated using the finite element analysis results of static and dynamic maximum bending stresses.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.6
• /
• pp.412-420
• /
• 2014

Water quality variations were investigated at 4 locations of Jungrang river (upper, middle and lower basins) during a period of 3 rainfall events. During the rainfall, concentrations of $COD_{Mn}$, SS and $BOD_5$ significantly increased, while the concentration of T-N decreased and that of T-P remained relatively constant. This pattern became more apparent as the level of accumulative precipitation and rainfall intensity increased. Simple regression analysis showed that the accumulative precipitation was positively correlated with all water quality pollutants except for T-N. With increasing accumulative precipitation, the concentration of T-N decreased, while the others increased. $R^2$ of simple regressions of hourly average rainfall intensity and water quality pollutants, showed wider range of variation ranged from 0.483 to 0.992, which indicated a strong correlation. The stronger the hourly average rainfall intensity, the more T-N and T-P in the upper basin, more $COD_{Mn}$ in the middle and lower basins, more SS with gradual increase from upper to lower areas, and more $BOD_5$ with gradual decrease from upper to lower region. Simple regression showed that water quality pollution in the upper basin was more sensitive to an increase of rainfall discharge than that in the middle and lower areas.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.558-569
• /
• 2017

In this paper, a 256Kb EEPROM IP aimed at battery applications using a single supply of 1.5V which is embedded into an MCU is designed. In the conventional cross-coupled VPP (boosted voltage) charge pump using a body-potential biasing circuit, cross-coupled PMOS devices of 5V in it can be broken by the junction or gate oxide breakdown due to a high voltage of 8.53V applied to them in exiting the program or erase mode. Since each pumping node is precharged to the input voltage of the pumping stage at the same time that the output node is precharged to VDD in the cross-coupled charge pump, a high voltage of above 5.5V is prevented from being applied to them and thus the breakdown does not occur. Also, all erase, even program, odd program, and all program modes are supported to reduce the times of erasing and programming 256 kilo bits of cells. Furthermore, disturbance test time is also reduced since disturbance is applied to all the 256 kilo bits of EEPROM cells at once in the cell disturb test modes to reduce the cell disturbance testing time. Lastly, a CG driver with a short disable time to meet the cycle time of 40ns in the erase-verify-read mode is newly proposed.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.2
• /
• pp.233-245
• /
• 2007

Previous finite element studies have shown that AASHTO Standard load distribution factor (LDF) equations appear to be conservative for longer spans and larger girder spacing, but too permissible for short spans and girder spacing. AASHTO LRFD specification defines the distribution factor equation for girder spacing, span length, slab thickness, and longitudinal stiffness. However, this equation requires an iterative procedure to correctly determine the LDF value due to an initially unknown longitudinal stiffness parameter. This study presents a simplified LDF equation for interior and exterior girders of two-span continuous I-girder bridges that does not require an iterative design procedure. The finite element method was used to investigate the effect of girder spacing, span length, slab thickness, slab width, and spacing and size of bracing. The computer program, GTSTRUDL, was used to idealize the bridge superstructures as the eccentric beam model, the concrete slab by quadrilateral shell elements, steel girders by space frame members, and the composite action between these elements by rigid links. The distribution factors obtained from these analyses were compared with those from the AASHTO Standard and LRFD methods. It was observed through the parametric studies that girder spacing, span length, and slab thickness were the dominant parameters compared with others. The LRFD distribution factor for the interior girder was found to be conservative in most cases, whereas the factor for the exterior girder to be unconservative in longer spans. Furthermore, a regression analysis was performed to develop simplified LDF formulas. The formulas developed in this study produced LDF values that are always conservative to those from the finite element method and are generally smaller than the LDF values obtained from the AASHTO LRFD specification. The proposed simplified equation will assist bridge engineers in predicting the actual LDF in two-span continuous I-girder bridges.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.11
• /
• pp.915-924
• /
• 2014

In an aero gas-turbine engine, a surface air-oil heat exchanger (SAOHE) is used to cool the oil system for the gearboxes and electric generators. The SAOHE is installed inside the fan casing of the engine in order to dissipate the heat from the oil system into the bypass duct stream. The purpose of this study was to develop an effective numerical method for designing an SAOHE for an aero gas-turbine engine. A two-dimensional model using a porous medium was developed to evaluate the aero-thermal performance of the fins of the heat exchanger, and a one-dimensional flow and thermal network program was developed to save time and cost in the evaluation of the heat exchanger performance. Using this network program, the pressure drop and heat transfer performance of the heat exchanger were predicted, and the results were compared with two-dimensional computational fluid dynamics results and experiment data for validation.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.33 no.4
• /
• pp.319-326
• /
• 2013

In the present study, we investigated the effects of high forage diets on the volume of udder, hormone level in blood, and lactation characteristics in the Holstein dairy cow. We divided into two groups; high forage diet [HF, concentrate: forage=4:6 n=41] and low forage diet [LF, 6:4 n=21]. Five cows were selected from each group based on their age for measuring the udder volume and the serum levels of estradiol and progesterone. Lactation characteristics were compared between HF and LF. The udder volume was 2.5 fold larger in HF at early gestation (p<0.01), but no difference was noted afterward. For the hormone levels, no significant difference was found between the groups. In HF, milk yield was significantly increased and maintained high longer, while somatic cell count was approximately 50% lower. Meanwhile, the milk fat content was significantly lower in HF during early lactating phase (p<0.001), but there was no difference thereafter. For milk protein and solid content, and MUN, no differences were found between the groups during lactation. Our results indicated that feeding high forage diets to dairy cows can increase milk yield and quality without notable changes in the udder volume and hormone level.