• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.786-791
• /
• 2007

Aerodynamically generated noise is dominant when the train speed approaches 300km/h. This noise sources is caused by the turbulent flow separations or vortex shedding from the train structure. Experiments were performed to investigate the characteristics of aerodynamic noise sources generated from exterior of the KTX trains and HSR-350x, especially from the inter-coach spacing. Measurements of both the inside and outside of the cabin are carried out to investigate the characteristics of the noise. Effect of the size of the mud-flap has been investigated through an wind tunnel test and it has been found that the low frequency noise is strongly dependent on the size of the gap. Also performed is an array measurement to locate different noise sources from the high-speed train. spectral characteristics of exterior noise sources are examined.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2011.01a
• /
• pp.121-124
• /
• 2011

본 논문에서는 다양한 형태의 장애인을 대상으로 유연하게 적용 가능한 공공자격시험의 표준화 시스템을 설계하고 개발한다. 1차적으로 4 ~ 6급의 저시력 시각장애인, 뇌병변 장애인, 손부위 등에 대한 지체 장애인을 대상으로 제안시스템을 개발하여 적용한다. 물리적 조건으로 공공자격에 응시하는 장애가 있는 수험자는 수검사항에 위반되지 않는 상태에서 일반 응시자와 별도로 키보드를 지참하여 응시 가능하나 행망용 다기능 한글 모아치기 키보드로 제한되어지고 최소 17인치 이상의 모니터가 제공되어지며 수험 장소에 대하여 특정좌석을 지정할 수 있다. 시험적 조건으로는 장애를 가진 수험자에 대하여 장애상태를 구분하여 일반인 대비 20 ~ 30%의 추가시간이 할당되어지고 실기시험에 대하여는 150%의 확대문자가 기본적으로 제공되어진다. 상위 조건으로 필기시험과 실기시험이 실시되며 특별하게 시각장애인에 대한 실기시험에서는 일반인에 대한 시험 종료 후 제안시스템 제어 하에서 별도의 추가시험 절차가 부가적으로 자동진행 되어진다. 본 구현시스템은 장애인을 위한 8단계의 세부기능 설정 후 13가지의 평가 항목을 설정하여 실제 공공자격시스템에 시험 적용한 결과, 평균적으로 매우우수의 최상급 평가를 받았으며 장애인에 기반 한 공공자격분야 글로벌 표준화 시스템으로 제시하기 위한 후속 연구를 진행하고 있다.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.43 no.6
• /
• pp.127-134
• /
• 2001

In order to expand agricultural lands in the western and southern coasts of Korean Peninsula, coarse soils excavated from hillsides have been used as fill materials for reclamation. In order to tackle with the problems and to confirm availability, research on soil improvement involve mixing cement to the fine wet soils. Required undrained shear strength$(C_u)$ for fill material was analysed to be 0.34~1.2 $kgf/cm^2$. It has been known that when cement is added to high water content marine clay its unconfined compression strength increased to 2 $kgf/cm^2$. Consolidation results show that pre-consolidation pressure increased to 1.8 $kgf/cm^2$and 3.4 $kgf/cm^2$ with the addition of 3% and 5% of cement respectively. This result shows that low-height embankments could be constructed without significant compression. Since the effectiveness of improvement may be different site by site, the mix design for each site is necessary in order to optimize it. The process is first to determine aimed shear strength and then optimum mix ratio of cement after carrying out a series of tests.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.2 s.119
• /
• pp.121-129
• /
• 2007

There has been much effort to find suitable methods for structural analysis in the mid-frequency region where traditional low frequency methods have increasing uncertainties whilst statistical energy analysis is not strictly applicable. Systems consisting of relatively stiff beams coupled to flexible plates have a particularly broad mid-frequency region where the beams support only a few modes whilst the plate has a high modal density and modal overlap. A system of two parallel beams coupled to a plate is investigated based on the wave method, which is an approximate method. Muller's method is utilised for obtaining complex roots of a dispersion wave equation, which does not converge in the conventional wave method based on a simple iteration. The wave model is extended from a single-beam-plate system, to a plate with two identical beams which is modelled using a symmetric-antisymmetric technique. The important hypothesis that the coupled beam wavenumber is sufficiently smaller than the plate free wavenumber is experimentally verified. Finally, experimental results such as powers and energy ratios show the validity of the analytical wave models.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.113-121
• /
• 2011

Rollover accident is one of the serious traffic accident and rollover accident takes high portion of all accident. The most common type of rollover is a tripped rollover which occupy 95% of all type of single-vehicle rollover. Tripped rollover occurs when a vehicle leaves normal road way and tripped by loose gravel, soil of fixed object such as guard rail, curbs and ditches. And the rest of the type of rollover is un-tripped rollover. An un-tripped rollovers that occurs during high-speed collision avoidance maneuvers. In this paper, presents the explanation of the un-tripped rollover test method and procedure, additionally this paper deals with various occurrence in the un-tripped test such as occurring excessive tire camber in the un-tripped test, tire side-wall contact with road surface and roll oscillation. And this paper analyzes the analysis of the roll rate amplitude in specific frequency through the FFT (Fast Fourier Transform) and the roll angle at the steering reverse timing which is the Fishhook test roll rate feedback time. Finally, this paper analyzes the relations between the estimated steady state roll gain and rollover stability.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.149-152
• /
• 2010

It was investigated that effect of the supersonic impulse turbine rotor leading edge thickness which was the part of 75 ton open cycle liquid rocket engine turbopump. The test for turbine was performed that the rotor thickness to pitch ratio was 1.9 and 1.4 to 30 ton turbine. As a result of test, the rotor with lower thickness(1.4) had 1.5% efficiency gain to the higher thickness(1.9) and the pressure ratio with maximum efficiency was increased to the nozzle full expansion point.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.240-244
• /
• 2017

Experimental verification in the rig test stage for component development is a vital link between the aeromechanical design and structural integrity validation process. Based on this premise, Non-Intrusive Stress Measuring System was adopted on the axial compressor test rig to measure the static and dynamic tip deflection of all blades by using tip-timing sensors. Through analyzing vibration characteristics, we evaluated the vibratory stresses seen on the blades fatigue critical location; detected synchronous resonances which are the source of High Cycle Fatigue (HCF) in blades; presented non-synchronous vibration response by aerodynamic excitation and individual blade mis-tuning patterns.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.2
• /
• pp.125-131
• /
• 2017

In order to develop test and performance analysis techniques for a CRP propulsion, a CRP dynamometer which can be installed inside the model ship was designed and manufactured. The object ship was the 16000TEU container carrier, which has test results for the single propeller. The design concept of the present CRP is that forward & after propellers have the same power ratio and their RPM ratio is 0.75:1. To begin with, we checked the performance of the CRP dynamometer through the calibration and then installed it inside the model ship. After the model ship setup including the design CRP and the rudder in the Large Cavitation Tunnel(LCT), a series of model tests composed of power ratio check, propeller behind wake(PBW) test, cavitation observation and pressure fluctuation tests was conducted. Through the model test and data analysis for CRP, the experimental technique was established and the improved method for CRP design was suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.9
• /
• pp.739-744
• /
• 2016

The truck that is used as running equipment for tank freight car support is a core structural part that supports the load of the car body and significantly influences the safety of freights and vehicles, as well as their running performance. Running equipment is composed of truck frames, wheels and wheel axles, independent suspensions, and brakes. Among these components, the truck frame supporting the load of the vehicles and freights may be the most important component. This study was carried out to analyze the structure of truck frames and to determine whether they are safe when the maximum vertical load, braking part load, and the front and rear load are applied to truck frames. This was achieved by subjecting the truck frames to stress tests and then measuring the stress on each part. The results of the stress tests showed that truck frames have a safe vehicle load design.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.178-183
• /
• 2004

Thermal stratification phenomena in the liquid oxygen tank of launch vehicle is caused by heat influx from ambient and non-equilibrium heat and mass transfer in the cryogenic tank. The thermal stratification study is needed for designing vent system, tank insulation, pump inlet. In this paper by investigating buoyancy driven boundary layer flow by side wall heating, one dimensional analysis of thermal stratification is peformed. thermal gradient is described with time.