• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.237-245
• /
• 2020

In decades, active sonar, which transmits signals and detects incident signals reflected by underwater targets, has been significantly studied since passive sonar in Anti-Submarine Warfare (ASW) detection performance becomes lowered, as underwater threats become their radiated noise reduced. In general, active sonar using Hull-Mounted Sonar (HMS) adjusts vertical tilt (depression) and sequentially transmits multiple Linear Frequency Modulation (LFM) subpulses which have non-overlapped bands, i. e. 1 kHz ~ 2 kHz, 2 kHz ~ 3 kHz, in order to reduce shadow zones. Recently, however, Generalized SFM (GSFM), which is generalized form of SFM, is proposed, and it is confirmed that subpulses of GSFM have orthogonality among each other depending on setting of GSFM parameters. Hence, in this paper, we applied GSFM to active target detection using HMS to improve the performance by the signal processing gain obtained from enlarged bandwidths of GSFM subpulses compared to those of LFM subpulses. Through simulation, we verified that when the number of subpulses is three, the matched filter gain of GSFM is approximately 5 dB higher than that of LFM.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.14 no.2
• /
• pp.72-78
• /
• 1981

The purpose of this study is to find directivity characteristics and relative gain of directivity of the wedge horn in conjunction with a projector with varing horn length, horn angle and frequency. The horns are constructed with aluminum plate covered with styrofoam. By using hinges the horn angle could be varied with wide range. Measurements were made over the frequency range of 25 KHz-100 KHz by varing the horn lengths from 5cm to 21cm and the horn angles up to 90 degrees. The followings were the results obtained from the study, 1. As the horn angle increased, the beam width for tile major lobe initially decreased and then increased. At 80 KHz with horn length 21cm the minimum beam widths were obtained with 16 degrees in horizontal plane and 36 degrees in vertical plane. 2. The maximum relative gains of directivity were 4.4 dB in horizontal plane and 3.4 dB in vertical plane when the horn length was 21cm. 3. Beam width was decreased with increasing of frequency. 4. When the mouth apertures were small the major lobes obtained by the experiment agreed with the computed ones, and when the mouth apertures were wide the major lobes by the observed were wide than the computed ones.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.4
• /
• pp.391-399
• /
• 2021

The conformal array sensor has different sub-array depending on different beam steering directions. According to the method to effective the sensor, the performance of the conformal array sensor can be different, where the sub-array selects an effective sensor. Also, due to the figure of the conformal array sensor, the figure of the sub-array can be different each other, which results in different performance on directivity index, beam width and etc. In this paper, two methods to select sub-array which is the criteria for each sensors position vector and directive vector were proposed. For two sub-array selection methods, the performance of the directivity index, horizontal and vertical beam width were compared with the average and variance. In addition, this comparison was conducted when the number of sensors was fixed. When the number of sensors was not fixed, the directional vector method mainly results in high performance, but the performance of vertical beam width was lower or equal. When the number of sensors was fixed, the performance of two methods is similar, but the performance of variance was deteriorated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.552-559
• /
• 2011

In this paper, the frequency reconfigurable antenna is proposed and designed. The proposed antenna is designed using the vertically stacked dipole structures and have the operating band for Cellular, PCS/WCDMA/Wibro/WiFi and WiMAX. The operating frequency band is selected by three pair of PIN diodes using the voltage difference between each dipole antenna and feeding transmission lines. The proposed antenna meets the required operating bandwidth and the maximum gain for each frequency band are measured as 6.3 dBi, 5.4 dBi and 5.8 dBi, respectively. The proposed antenna in this paper can be applied for the future mobile small base station or repeater antenna because this antenna can provide the small size and high gain features.

• Information Systems Review
• /
• v.12 no.2
• /
• pp.1-23
• /
• 2010

Most enterprise information systems today are silo systems in that they are not properly aligned nor integrated with one another. Such silo systems result because enterprises lack an architectural perspective in the planning and development of the systems. This paper proposes an Enterprise Architecture Orientation Model as a framework for the analysis, planning and design of the architectural quality of enterprise information systems. The model decomposes enterprise architecture into two dimensions-alignment and integration, and specifies for each dimension the general development and evolution stages enterprises may traverse. The alignment dimension represents the vertical strategic alignment of the systems with the vision, mission, strategy and goals of the enterprise, and is analyzed in terms of the performance, capability, and strategy of the enterprise. The integration dimension, on the other hand, represents the horizontal and functional integration among the systems that span organizational functions and boundaries, and is analyzed in terms of such technological components as IT infrastructure, data, application, and business processes. The model combines the alignment and integration dimensions to form a two-dimensional conceptual space for mapping the architectural quality of the enterprise. It is proposed that an enterprise use the model to identify and understand its position now and in the future in the architectural quality of the enterprise information systems. It is also proposed that the model provides a tool for the planning and design of the transition from one stage to the next in the alignment and integration of the systems to reach an architectural maturity. At the end, the paper discusses how the model can be applied differently according to the strategic orientation of the enterprise. An example of the usage of the model is presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.9 s.112
• /
• pp.900-912
• /
• 2006

A GPS receiving antenna installed in the missile's warhead is designed and fabricated at a center frequency 1.575 GHz. The circular shaped antenna is installed in the middle of the warhead where the antenna's patch and the ground plane are connected with a hollow cylindrical shaped short pin. Using the dual feeding and phase difference method, an omni-directional radiation pattern which direction is normal to the missile's axis(H-plane) is obtained. The optimized diameters of the circular patch and the cylindrical ring typed shorting pin of the GPS receiving antenna which use the FR4.material(dielectric constant $\varepsilon_r=4.6$) are 59.5 mm and 14 mm, respectively. The cylindrical body with diameter 100 mm and height 500 mm is attached to the lower part of the warhead in order to complete the missile figure. The radiation patterns are measured by changing the angle and phase between the dual feeding points. When the phase difference of dual feeding is $100^{\circ}$ and the angle between the dual feeding points is $100^{\circ}$, the nearly omni-directional radiation pattern in the H-plane is obtained. In this case, the antenna gain is -5.55 dBd and the relative level difference between the maximum and the minimum radiation intensity is 3.98 dB.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.3
• /
• pp.1-8
• /
• 2015

The most used smart set-top box in home driven by the Android OS and based on Wi-Fi technology has to ensure nothing wrong with the Wi-Fi service regardless of the various user's installation environment. The direction test method about the nondirectional of the Wi-Fi doesn't be determined as the standard and each manufacturers devise the their own test methods and conduct the tests. In this paper, we created the 720 test cases considering 2 components of upload & download, the 10 elements of the vertical angle and the 36 elements of the horizontal angle looking at the wireless router in order to verify omni-directional Wi-Fi capability. In reality, from viewpoint in terms of cost and time constraint, it is difficult to test all the test cases. Therefore, we decided to reduce test cases by applying Pair-wise testing technique which is one of combinational testing techniques based on ISO / IEC 29119-4. And we obtained the test cases in which the Pair-wise technique was applied by Allpairs tool which output test cases automatically and conducted the test. It could be confirmed that the proposed technique shortened 48.61% of the time to be spent in progressing the existing test cases and that the trace about the part in which the problem was generated with the result of the simplified test case was possible enough.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.1
• /
• pp.7-13
• /
• 2007

In this paper, we have designed and fabricated a small size wide-band monopole antenna which can integrate the frequency of previous business mobile communication system by adding 4 PCS of post type parasitic element on top-loaded sleeve monopole antenna. We have observed the properties of return loss upon a parameter change of element, and we also examined radiation properties in the band of PCS, W-CDMA, WiBro, W-LAN and S-DMB in order to make sure the suggested antenna's wide-band properties. We have found that the proposed antenna has omni-direction in horizontal plane and figure eight-direction in vertical plane, and we could have good return loss($Return\;loss{\leq}-10\;dB$) and $1.14{\sim}3.66\;dBi$ gain in $1.67{\sim}3.55\;GHz$ of frequency range($B/W{\fallingdotsep}72%$).

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.489-496
• /
• 2019

In this paper, we design and fabricate an ultra small dual crossed dipole antenna operating at 2.4 GHz frequency. In order to miniaturize the size of the antenna so that it can be applied to a mobile device, a cross dipole is disposed on the upper two layers and a reflection plane, a horizontal matching circuit and a ground plane are arranged on each layer. The circuit was connected by a vertical through-hole. The size of the fabricated antenna is $21.61mm{\times}16.88mm{\times}1.27mm$, the measured reflection coefficient is -31.5 dB, and the bandwidth below -10 dB is 112 MHz. In addition, since the gain of the antenna is -4 dBi, it has the omnidirectional radiation characteristic, so it can be applied to various fields as an antenna for mobile devices.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.235-239
• /
• 1996

분류가 모서리에 충돌할 때 발생하는 순음성 소리인 쐐기소리(edgetone)는 공력음향의 대표적인 현상으로서 지금까지 수많은 연구가 있어 왔으며 그 대부분의 특성이 규명되었다고 할 수 있다. 쐐기소리의 발생기구인 되먹임(feedback) 이론을 처음으로 제안한 이는 Powell로서 그는 되먹임사이클의 위상조건에 의하여 주파수특성에 관한 모델을 제안하였으며, 최근 그 모델의 위상인자에 관하여 Kwon은 새로운 값을 제안한 바 있다. 그런데, 쐐기소리의 이론은 주로 분류가 쐐기나 벽에 충돌할 경우에 집중되어 왔으며 분류가 원통에 충돌하여 발생하는 경우에 관한 연구는 Krothapalli의 초음속분류에 관한 연구와 Mochizuki등의 아음속분류에서 원통지름의 영향에 관한 연구를 들 수 있을 뿐이다. Mochizuki등은 원통의 지름이 노즐의 높이보다 작은 경우에 쐐기 소리의 주파수가 원통의 와류이탈(vortex shedding) 주파수와 같은 것을 관찰하였다. 그러나 분류와 원통이 작용하여 발생하는 쐐기소리의 주파수 특성에 관한 이론적 해석을 시도한 연구는 없으며 또한 방사음장의 특성에 관하여도 Han과 Kwon에 의한 모델이 발표된 바 있으나 실험적으로 입증되지 못하였다. 따라서, 본 연구의 목적은 2 fig.1과 같이 2차원 분류가 원통에 충돌할 때 발생하는 쐐기소리의 주파수특성의 정량적인 모델을 세우고 방사음장의 지향특성의 이론 모델을 확립하는 것이다. 먼저 주파수특성을 실험하고 되먹임이론을 적용하여 분석하므로써 유효음원의 위치를 구하고 또한, 수직벽에 작용하여 발생하는 충돌음(impinging tone)의 경우를 실험하여 주파수특성을 비교 고찰하므로써 유효음원의 위치에 관한 이론을 입증한다. 아울러 원통과 평면벽의 각 경우에 방사음장의 지향특성을 측정하고 고찰한다.2,5,6]을 단계별로 고찰하여, 점점 까다로워져 가는 선박 진동규제[3,4]에 대처하고 승무원의 안락성에 대한 욕구, 구조물의 안전성, 장비의 성능보존이 만족되는 저진동 선박의 건조를 위해 향후 해결해야할 과제들을 도출하여 선박진동분야이 연구개발 방향을 제시하고자 한다. 하는 것은 진단의 정밀도에 문제가 있을 것으로 생각된다. 따라서 언어적진리치가 도입되어 [상당히 확실], [확실], [약간 확실] 등의 언어적인 표현을 이용하여 애매성을 표현하게 되었다. 본 논문에서는 간이진단 결과로부터 추출된 애매한 진단결과중에서 가장 가능성이 높은 이상원인을 복수로 선정하고, 여러 종류의 수치화할 수 없는 언어적(linguistic)인 정보ㄷㄹ을 if-then 형식의 퍼지추론으로 종합하는 회전기계의 이상진단을 위한 정밀진단 알고리즘을 제안하고 그 유용성을 검토한다. 존재하여도 모우드 변수들을 항상 정확하게 구할 수 있으며, 또한 알고리즘의 안정성이 보장된 것이다.. 여기서는 실험실 수준의 평 판모델을 제작하고 실제 현장에서 이루어질 수 있는 진동제어 구조물에 대 한 동적실험 및 FRS를 수행하는 과정과 동일하게 따름으로써 실제 발생할 수 있는 오차나 error를 실험실내의 차원에서 파악하여 진동원을 있는 구조 물에 대한 진동제어기술을 보유하고자 한다. 이용한 해마의 부피측정은 해마경화증 환자의 진단에 있어 육안적인 MR 진단이 어려운 제한된 경우에만 실제적 도움을 줄 수 있는 보조적인 방법으로 생각된다.ofile whereas relaxivity at high field is not affected by τS. On the other hand, the change in τV does not affect low field profile but strongly in fluences on both