• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.6
• /
• pp.59-68
• /
• 2022

We propose the vehicle maintenance support system to alarm consumable replacement reminders to the vehicle owner. Since the delayed replacement of the consumables makes the condition of the vehicle worse, it is crucial to replace consumables in a recommended period. The vehicle maintenance support system alarms the replacement time, which is set by the vehicle owner, based on the mileage of the installed vehicle. It integrates speed information acquired from the Controller Area Network interface for communication between Electronic Control Unit and instrument panel, exposed at the On Board Diagnostics-II port, to calculate the vehicle mileage. By this, there is no additional wiring required for the system. We verify the system has only 0.28% error by comparing the mileage on the system with the instrument cluster on the vehicle. It automatically enters low-power mode consuming 15mW, which is a negligible amount for the typical conditions of the car, to prevent the vehicle battery from discharging when the ignition is off.

• Journal of Korea Society of Industrial Information Systems
• /
• v.15 no.1
• /
• pp.1-14
• /
• 2010

It is recently issued scalability, mobility and external internet connection on Wire-less sensor network. The low power wireless sensor networks based on IPv6 technology 6LoWPAN technology is being standardized in the IETF. This paper for the 6LoWPAN environment based on the routing protocol LOAD, route cost applied the packet re-transmission rate which follows in Link Qualities price which uses at course expense and packet transmission Minimum route Cost routing protocol where does on the course wherethe smallest packet re-transmission becomes accomplished proposed. The technique which proposes compared and LOAD and AODV that about 13%, about 16% energy consumption is few respectively averagely, Energy of the entire network equally, used and energy effectiveness and improvement of network life time experiment led and confirmed.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.231-238
• /
• 2011

Variable message signs(VMS) in use are being displaying with the LED device as the luminous source, and it is a recent trend to be changed from the Lamp type to the Surface-Mount Devices(SMD) type. The LED device leads to get VMS display brightly and clearly, leading to have visibility and legibility better than the existing VMS. However, the lights which display off the road, the unnecessary energy, might have negative effect on ecosystem. This study developed the way of getting the lights be displayed only to drivers without the unnecessary energy and estimated the energy efficiency of the development by the optical testing. As a result, this study showed that the energy consumption of the developed display device appeared to decrease by about 36.1% compared to the existing device. Also the upward and downward angle of the lights changed from an angle of $24^{\circ}C$ to $0^{\circ}C$and from an angle of $-24^{\circ}C$ to $-11^{\circ}C$, respectively. Therefore, it anticipates that the developed device would benefit highway safety due to an improvement in visibility and legibility compared to the existing VMS and the energy consumption would be less lower than the existing VMS.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.3
• /
• pp.25-34
• /
• 2018

This paper presents a heating source of carbon nanofibers for the efficiency and the drying performance of laundry dryer, and focuses on the applicability-evaluation of its source. To design the proposed heating module, experiments were conducted in terms of surface temperature and surface temperature distribution characteristics of carbon nanofiber lamps. The surface temperature of the lamps increased linearly with increment of a current to flow a lamp and revealing the increasing pattern as the length of the ramps is shorter. The proposed heating source was evaluated based on drying efficiency, moisture evaporation rate at laundry, and internal temperature of a drum during drying process. The drying efficiency satisfied a 45% which is specified in KS C 9319. The moisture evaporation rate and the internal temperature of the drum were respectively 98.88% and $61.1^{\circ}C$, which are similar to that of S's company dryer. From the evaluation and actual drying test results, the proposed carbon nanofiber lamp heating module is considered to be applicable as a heat source for laundry dryer in terms of drying efficiency and drying performance. it is possible to obtain a heat source at a high temperature, an excellent calorific value, an improvement in drying performance, and an effect of sterilizing laundry due to the emission of far-infrared rays. In addition to the applicability, the difference of the drying efficiency between the dryers was analyzed in detail based on the power consumption of the heat sources.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.5
• /
• pp.879-886
• /
• 2008

This paper addresses the analysis and the design optimization of differential interconnects for Low-Voltage Differential Signaling (LVDS) applications. Thanks to the differential transmission and the low voltage swing, LVDS offers high data rates and improved noise immunity with significantly reduced power consumption in data communications, high-resolution display, and flat panel display. We present an improved model and new equations to reduce impedance mismatch and signal degradation in cascaded interconnects using optimization of interconnect design parameters such as trace width, trace height and trace space in differential flexible printed circuit board (FPCB) transmission lines. We have carried out frequency-domain full-wave electromagnetic simulations, time-domain transient simulations, and S-parameter simulations to evaluate the high-frequency characteristics of the differential FPCB interconnects. The 10% change in trace width produced change of approximately 6% and 5.6% in differential impedance for trace thickness of $17.5{\mu}m$ and $35{\mu}m$, respectively. The change in the trace space showed a little change. We believe that the proposed approach is very helpful to optimize high-speed differential FPCB interconnects for LVDS applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.9
• /
• pp.1837-1844
• /
• 2009

In this paper, the circuit of 2 variable ternary adder and multiplier circuit using current mode CMOS are implemented. The presented ternary adder circuit and multiplier circuit using current mode CMOS are driven the voltage levels. We show the characteristics of operation for these circuits simulated by HSpice. These circuits are simulated under $0.18{\mu}m$ CMOS standard technology, $5{\mu}A$ unit current in $0.54{\mu}m/0.18{\mu}m$ ratio of NMOS length and width, and $0.54{\mu}m/0.18{\mu}m$ ratio of PMOS length and width, and 2.5V VDD voltage, MOS model Level 47 using HSpice. The simulation results show the satisfying current characteristics. The simulation results of current mode ternary adder circuit and multiplier circuit show the propagation delay time $1.2{\mu}s$, operating speed 300KHz, and consumer power 1.08mW.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.1
• /
• pp.198-204
• /
• 2012

Generally, the clustering of sensor nodes in WSN is a useful mechanism that helps to cope with scalability problem and, if combined with network data aggregation, may increase the energy efficiency of the network. The Hierarchical clustering routing algorithm is a typical algorithm for enhancing overall energy efficiency of network, which selects cluster-head in order to send the aggregated data arriving from the node in cluster to a base station. In this paper, we propose the improved-LEACH that uses comparably simple and light-weighted policy to select cluster-head nodes, which results in reduction of the clustering overhead and overall power consumption of network. By using fine-grained power model, the simulation results show that i-LEACH can reduce clustering overhead compared with the well-known previous works such as LEACH. As result, i-LEACH algorithm and LEACH algorithm was compared, network power-consumption of i-LEACH algorithm was improved than LEACH algorithm with 25%, and network-traffic was improved 16%.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.1
• /
• pp.23-30
• /
• 2017

Currently, road lightings are installed with less than 400W of existing metal halide lamps. These road lightings are being replaced by energy-saving lightings. Induction lamps are expected to be more actively replaced with targets for tunnel lighting and high ceiling lighting. Therefore, it is necessary to develop high efficiency, high power induction lamps system. In this study, the gas type & pressure, amalgam type were designed for the high power of the induction lamps. And induction lamp system was optimized through electrical, optical characteristics analysis. It is optimized to the gas pressure 300~350 [mmHg] for the discharge tube of high power induction lamp and ferrite core. The driving circuit matching was completed with a induction lamp using indium amalgam. The rated power consumption of the induction lamp was optimized with 250 W (rated ${\pm}10%$)

• The KIPS Transactions:PartA
• /
• v.12A no.3 s.93
• /
• pp.223-228
• /
• 2005

Several researchers have pointed out that the energy consumption in memory takes a dominant fraction on the energy budget of a whole embedded system. This applies to the embedded Java virtual machine tn, and to develop a more energy-efficient JVM it is absolutely necessary to optimize the energy usage in Jana memory. In this paper we have analyzed the logical memory access pattern in JVM as it executes numerous number of bytecode instructions while running a Java program. The access pattern gives us an insight how to design and select a suitable memory technology for Java memory. We present the memory access pattern for the three logical data spaces of JVM: heap, operand stack, and local variable array. The result saws that operand stack is accessed most frequently and uniformly, whereas heap used least frequently and non-uniformly among the three. Both heap and local variable array are accessed mostly in read-only fashion, but no remarkable difference is found between read and write operations for operand stack usage.

• The KIPS Transactions:PartC
• /
• v.14C no.2
• /
• pp.171-178
• /
• 2007

In mobile ad hoc networks, an application scenario requires mostly group mobility behavior in the mix of group moving nodes and individually moving nodes. The nodes of those applications tend to belong to the movement group with similar movement behavior. Group mobility is one of the good methods to improve scalability, and reduces the protocol overhead. In this paper, we propose the multicast architecture which regards nodes that have equal group mobility in the heterogeneous group mobility network as the single entity with the multiple interfaces and composes multicast tree, The logical cooperative entity-based multicast architecture accommodates the scalability, the multicast tree simplification, and the protocol overhead reduction which arc obtained from the hierarchical multicast architecture, while it maintains the nat multicast architecture for the data transmission. It also prevents the concentration of the energy consumption dispersing data forwarding load into the several ingress/egress nodes. Results obtained through simulations show that logical cooperative entity based multicast protocol with multiple interfaces offers the protocol scalability and the efficient data transmission.