• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1889-1894
• /
• 2012

A small-scale chamber test laboratory for controlled low strength materials with bottom ash and recycled in-situ soil have been carried out. Laboratory test which was simulated during construction stage was conducted. The vertical deflection of 4.43mm to 6.6mm, and the horizontal deflection of 5.49mm to 15.9 mm were measured during backfilling. In case of loading, the vertical deflection of 2.41mm to 8.69mm, and the horizontal deflection of 1.66mm to 2.53mm were measured. Its residual deflections were 1.40mm to 5.93mm for vertical and 1.66mm to 2.53mm for lateral. The vertical and horizontal deflecto of controlled low strength materials were smaller than that of sand backfill. Also, it was same trend for the measured surface settlement.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.3
• /
• pp.522-527
• /
• 2015

We applied a displacement current measurement technique for the study of L-${\alpha}$-dilauryl phosphatidylcholine (DLPC) monolayer. Displacement current was generated at the DLPC monolayer on the water surface, while induced by compression and expansion of the monolayer. Generation of Maxwell displacement current (MDC) was observed when surface areas per DLPC molecule were approximately $200{\AA}^2$ and $40{\AA}^2$. We investigated MDC for monolayer compression cycles, and found that MDC reached the maximum at the molecular area, which was measured right before surface pressure began to increase during compression cycles. The monolayer surface morphology of Langmuir-Blodgett (LB) films was characterized using atomic force microscope (AFM). As a result, we measured the result from the microscopic properties shown in the AFM images of LB films that molecules in the monolayer were in good orientations and the thickness of the monolayer ranged from 5 to 10 nm.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.4
• /
• pp.29-36
• /
• 2010

To investigate the cyclic characteristics of exterior joints in RC frame buildings which are typically used after 1988, 70% scaled T-shaped beam-column subassemblies were designed and tested with a displacement control that is composed of 9 steps, until 3.5% story drift was reached. Axial forces are applied to columns during the experiment to simulate a real situation. The results show that the non-seismic detailed specimens failed before reaching 0.85% story drift, and their strengths are less than 0.85 times the nominal flexural strength which beam or columns should reach. The relationship of principal stress and story drift of exterior joints is similar to the one that Priestly proposed.

• Journal of the Korean Magnetics Society
• /
• v.6 no.2
• /
• pp.106-111
• /
• 1996

Electric machines such as motors which have rmving parts are designed for producing mechanical force or torque. The accurate calculations of electromagnetic force and torque are important in the design these machines. Electromagnetic force calculation method using the results of Finite Element Method(FEM) has been presented variously in 2-D problems. Typically the Maxwell's Stress Tensor method and the method of virtual work are used. The former calculates forces by integrating the surface force densities which can be expressed in terms of Maxwell Stress Tensor(MST), and the latter by differentiating the electromagnetic energy with respect to the virtual dis¬placement of rigid bodies of interest. In the problems including current source, magnetic vector potentials(MVP) have rmstly been used as unknown variables for field analysis by a numerical method; e. g. FEM. This paper, thus, introduces the two both methods using MVP in 3-D case. To verify the usefulness of presented methods, a solenoid model is chosen and analyzed by 3-D and axisymmetric FEM. It is found that the force calculation results are in good agreement for several mesh schemes.

• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.55-61
• /
• 2015

In this paper, the displacement behavior characteristic of hollow rollers with various cross sectional area profiles and circular plate for load supporting capacity increment has been presented using a finite element method. The FEM results present that the hollow roller with X-shaped or Y-shaped columns between outer tube, middle tube and inner tube reduces a maximum displacement at the middle length of hollow rollers. And the circular plate, which is inserted at the middle of the hollow roller, is very useful to reduce the maximum displacement of hollow rollers with the plate thickness of 30~40mm. This paper presents the weight vs the maximum displacement ratio in which is represented for the optimized design as a function of a hollow roller total weight. The FEM analyzed results recommend the design model 4, 5 and 6 of hollow rollers for decreasing the ratio of maximum displacement and total weight of hollow rollers.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.40-48
• /
• 2016

To observe the rail-slab interaction in continuous welded railway(CWR) bridge when earthquake occurs, additional axial rail stresses and relative longitudinal displacements between rail and bridge deck were calculated with input of various load combinations and 3 different types of seismic loads to an analytical model. As results of analysis, it can be found that standard response spectrum proposed by Korea Rail(KR) network authority for earthquake design showed less additional axial rail stresses than allowable levels, but greater relative longitudinal displacement between rail and bridge deck, which means that adjustment of relative longitudinal displacement within a standard level is much more difficult than axial train stress. Additionally, if a large-scaled earthquake as occurred at Kobe, Japan comes up, then both of additional axial rail stress and relative displacement in rail-bridge deck may exceed allowable levels, which indicates to make proper design guides against sudden earthquake occurrence.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.98-106
• /
• 2019

Human-powered aircraft has wings with a shape of high aspect ratio which results in large bending displacement. This paper aims to improve the structural limitation by changing an incidence angle of the wings. The tendency change of bending displacement at the wing tip is observed assuming that airfoil and cross-sectional shape of the wing is fixed, and amount of the total lift generated is satisfied. Quasi-steady lift, drag and the aerodynamic moment are distributed with regard to sections of the wing. Those are analyzed using a numerical nonlinear lifting-line method and 'geometrically exact beam' (GEB) program in EDISON. 'Variational Asymptotic Beam Sectional Analysis' (VABS) program is used to check if the present wing is structurally solid. Furthermore, the predicted tip deflections are verified by comparing with DYMORE.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4C
• /
• pp.221-230
• /
• 2008

The George Massey immersed tunnel passes the Fraser River near Vancouver, Western Canada. The tunnel was founded on sandy soils and its behavior during earthquake was analyzed by an effective stress constitutive model called UBCSAND. This model is able to calculate pore pressure rise and resulting tunnel movements due to cyclic loading. Centrifuge tests conducted at Rensselaer Polytechnic Institute (RPI) were used to verify the model performance. The centrifuge tests consisted of 2 models: Model 1 was designed for an original ground condition, Model 2 for a ground improvement by densification. In Model 1, large deformation of the tunnel was observed due to liquefaction of surrounding soil. Because of the densified zones around the tunnel the vertical and horizontal displacements of the tunnel in Model 2 was 50% less than Model 1. Measured excess pore pressures, accelerations, and displacements from centrifuge tests were in close agreement with the predictions of UBCSAND model. Therefore, the model can be used to predict seismic behavior of immersed tunnels on sandy soils and optimize liquefaction remediation methods.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.292-295
• /
• 2009

본 논문에서는 평판구조물의 정적 및 동적해석에 사용할 목적으로 성능이 향상된 평판유한요소를 제시하였다. 이 요소는 비적합변위형과 선택적 감차적분방법 그리고 대체전단변형률장을 복합적으로 적용하여 각각의 장점들을 포함하는 향상된 거동을 보여주고 있다. 또한 비적합변위형의 적용으로 발생되는 조각시험의 실패 문제점을 해결하기 위하여 직접수정법을 평판유한요소의 개선에 사용하였다. 대표적인 검증문제에 대한 수치해석작업을 통하여 본 연구에서 개발한 요소는 가상적인 제로에너지모드 및 전단잠김현상의 발생과 같은 문제를 나타내지 않음을 알 수 있었다. 특히 찌그러진 형상으로 모형화 한 경우에 있어서도 전단잠김현상이 발생하지 않았다. 본 연구에서 수행한 동적반응해석 시험에 있어서도 이론해와 잘 일치하는 결과를 보여주었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.665-670
• /
• 2006

In this paper, the results of empirical methods and the numerical analysis were compared and investigated on the lateral displacement due to embankment in soft soil. The empirical methods gave different results so the possibility of lateral displacement could not be determined only by the empirical methods. The numerical analysis could be used so effectively that its result showed useful lateral and vertical displacements with depth and distance.