• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.6
• /
• pp.35-41
• /
• 2007

The rate of loading in motor operated valve(MOV) can be defined as a variation of correlation between the actuator torque and the thrust upon the variation of operating load. This paper contains the analysis of characteristic and the validity of loading rate in the opening stroke of gate type motor operated valve. Also, this paper describes the evaluation result of loading rate for 40 MOVs' opening stroke using newly derived methodology in this study. Author has found a result that loading rate of opening stroke gets a negative value when the differential pressure is higher than 150 psi and this value goes up depending on the amount of the differential pressure.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.6
• /
• pp.26-32
• /
• 2009

We have constructed loading apparatuses to electrical motor with a powder brake and a oil pump for load test of a several ten kilowatt-motor and performed load test with two motors. On operating the loading apparatus with a oil pump, temperature of the oil may excessively increase and fail to operate due to dynamic energy loss of equipment in oil loop. In order to control the oil temperature, factors of the energy loss were analyzed and the quantitative loss was calculated. Load tests of motors with two loading apparatuses constructed were successfully performed and strengths of each apparatus come out on operating.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.452-453
• /
• 2006

저압 개폐기는 에어컨, 냉동기, 쇼케이스, 산업용 청소기, 전기 온수기, 건조기, 공조기, 펌프, 콤프레셔 등의 모터제어 및 히터와 조명기기의 개폐 등에 광범위하게 이용되는 개폐장치이다. 저압 전자개폐기는 수 천회에서 수백만회까지 빈번한 개폐사용조건으로 인해 시험규격에서는 개폐시험을 통해 수명을 검증하도록 되어 있다. 이 개폐시험 회로는 규정된 전압, 전류, 역률 조건을 맞추기 위해 저항과 리액터를 직렬 연결하여 구성한다. 또한 모터와 같은 리액터 부하를 개폐하는 개폐기의 경우는 전류차단 순간 과도회복전압의 피크비와 주파수를 규정하여 적용하고 있다. IEC60947-1에서는 과도회복전압의 피크비와 주파수에 대한 규정값을 제시하고 있으며 제시된 값을 제어하기 위한 회로를 제시하고 있다. 과도회복전압의 피크비와 주파수는 개폐기 접점의 절연성능과 밀접한 관계가 있으며 수명에 치명적인 영향을 미친다. 본 연구에서는 LS산전(주) 부하개폐시험 회로의 과도회복전압 조건과 영향을 설명하고 제어하기 위한 저항과 커패시터를 적용하는 방법을 제안하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.379-382
• /
• 2011

Engine test as well as unload test of starting motor itself was performed to evaluate the braking characteristics of starting system used for initial spin-up of gas turbine for power generation. Through the experimental evaluation of the braking performance with the capacity of braking resistor of the starting motor, we have achieved quantitative data to secure robust braking characteristics in emergency during the starting period of the gas turbine. It is possible to establish a capacity selection criterion of braking resistor to ensure the starting reliability of the gas turbine.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.1 s.28
• /
• pp.16-22
• /
• 2005

This paper presents the method of ROL(Rate Of Loading) improvement for the Motor Operated Gate Valve operated in high differential pressure condition. ROL is one of the most important evaluation parameters for the valve ability. It is close to correlation in stem factor (SF) and appears different value by the differential pressure of fluid. ROL and SF are analyzed by the static test and dynamic test. The obtained result show that the modification of stem factor is very important factor for the ROL improvement. In order to obtain the same value of SF between static and dynamic test, stem and stem nut should be combined appropriately by the repetition test.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.562-567
• /
• 2003

This paper presents the method of Rate of Loading(ROL) improvement for the Motor Operated Gate Valve operating in high differential pressure condition. The character of ROL and Stem Factor is analyzed. Static test and dynamic test were performed and acquired the diagnosis signal for the valve closing stroke. The result of this study is the modification of stem factor is very important factor for the ROL improvement. In order to obtain the same value of dynamic test thread friction coefficient stem and stem nut should be combined appropriately.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.525-531
• /
• 2011

Recently, the demand of environmentally friendly transportation has increased due to the environmental issues. Electric two-wheeled vehicles do not have the noise pollution nor exhaust gases of vehicles with internal combustion engines. Performance evaluation of an electric two-wheeled vehicle was carried out. A driving test on outdoor roads was performed and a chassis dynamometer was used. The chassis dynamometer simulates the road load of the vehicle. The road load influences the tests using the chassis dynamometer. The differences between the table method and the coasting test for setting the road load was compared and analyzed.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.67-68
• /
• 2010

다중동력시스템은 하나의 엑셀에 두개의 모터를 연결하여 구동하는 시스템으로 차량의 부하가 적은 경우 한대의 모터로만 운전을 하고 경사로의 등판이나 화물의 양이 증가해 부하가 커지는 경우 두 대의 모터를 운전하는 병렬 동력원을 가지는 차량 제어 시스템을 말한다. 다중동력시스템에서 PMSM의 제어는 전류 제어와 속도 제어로 구현이 가능하다. 본 논문에서는 다중동력 시스템에 적용이 가능한 인버터에 대해 벡터 제어 알고리즘의 PSIM 시뮬레이션과 시험을 수행하여 제안한 제어기의 유용성을 검증하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.3
• /
• pp.17-26
• /
• 2004

In this paper, power transmission systems converts the shaft power of a Turbo-shaft Engine with Free Power Turbine into the generator power and be composed of a method being supplied in the thrust motor driving a propellers. Being used this, Gas turbine engine works to flat rating about 110 kw (147 shp) that the thrust motor be extremely supplied from the engine of 317shp. In this test equipment, the engine is installed with the flywheel being able to the damping function when happen to the varying load between gas turbine engine output-shaft and generator. Then if the flywheel of inertial moment be not considered, the generator and motor not get the required power from the engine for raising the load. Also it is certified that the engine works the abnormal operation. Hence the flywheel of inertial moment is determined the required range to do the performance analysis with the dynamic transient from the given and tested engine data. This system is able to get the required power after a mounting test with the redesigned flywheel.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.1
• /
• pp.74-80
• /
• 2002

A propulsion system apparatus for railroad vehicle is estimated it's performance because of safety and confidence. In general, flywheel type testing method is widely used in the equipment. However, mechanical inertia generated by the flywheel can not be varied (or controlled) and can not be represent actual running resistance. In this study, we have focused on the development of variable vehicle load generation. Therefore, we have proposed the method which uses variable vehicle load controlled by vector motor to get the characteristics of the real vehicle load and confirmed the results with those of computer simulations.