• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.63-70
• /
• 2008

In this paper, a smart sensor system for the MEMS pressure sensor was developed. A compensation algorithm and programmable calibration circuits were presented to eliminate errors caused by temperature drift of piezoresistive pressure sensors in itself. This system consisted of signal conditioning, calibration, temperature detection, microprocessor, and communication parts and these were integrated into a SOC. A RS-232 interface was employed for monitoring and control of a smart sensor system. The area of fabricated IC is $4.38{\times}3.78\;mm^2$ and a $0.35{\mu}m$ high voltage CMOS process was used. Compensation error for temperature drift of 50 KPa pressure sensors was measured into ${\pm}0.48%$ in the range of $-40^{\circ}C{\sim}150^{\circ}C$. Total power consumption was 30.5 mW.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.8
• /
• pp.1055-1062
• /
• 2001

Study, it is the purpose to develope a cheap and compact pulsed $CO_2$ laser with pulse repetition rate range of 1 KHz. We used a IGBT switched power supply as a power supply, which is cheap and simple comparing to others. PIC one-chip microprocessor was used for precise control of a laser power supply on the control part. And the laser cavity was fabricated as an axial and water cooled type. The laser performance characteristics as various parameters, such as pulse repetition rate, gas pressure, and gas mixture rate have been investigated. The experiment was done under the condition of total pressure of $CO_2$： $N_2$：He ＝ 1：3：10, 1：1.5：5, 1：9：15 from 6 Torr to 15 Torr and pulse repetition rate from 100 Hz to 900 Hz. As a result, the maximum average outpu was about 20.5 W at the total pressure of 15 Torr, the gas mixture $CO_2$：$N_2$：He ＝ 1：9：15 and the pulse repetition rate of 700 Hz.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.2
• /
• pp.36-40
• /
• 1993

In order to improve complicated construction and complex control which are disadvantage of optimal PWM technique aimed at harmonic elimination method, this paper presented MRA(Model Reference Adaptive) PWM technique that gatmg signal of inverter is generated by comparing the reference signal with the induced feedback signal at the reference model of load. Design of controller is composed of microprocessor and analog circuit. MRA PWM technique used in the paper is able to compensate the degradation of voltage efficiency to be generated by the ratio of the output voltage to the DC supply voltage being low for using conventional sinusoidal PWM technique. When the trapezoidal signal is employed as the reference signal. the low order harmonics of line current can be reduced and the switching pattern is made by on-line computation using comparatively simple numerical analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6B
• /
• pp.423-432
• /
• 2012

We design a control circuit that can switch input power between a rechargeable battery and a sensor communication device (mote) depending on the operating state of a solar cell as well as the active and sleep mode of a sensor MAC protocol. A mote that simply combines a solarcell and a rechargeable battery may die if there is not sunlight long. A battery is recharged if sunlight is sufficient and a device is in a sleep mode, and it supplies power if sunlight is low and the mote is in an active mode. A mote can switch its input power between solar cell and battery depending on the output level of a solar cell. During this switching, a mote may lose its state information due to the reset of a microprocessor by the transient power-off. A capacitor is used to cope with this phenomenon and also supplies power to a mote during a sleep mode. Experimental results show that the solar cell based mote operates in a very stable manner against the lack of sunlight long.

• Journal of the Korean Society of Radiology
• /
• v.5 no.3
• /
• pp.127-134
• /
• 2011

In this paper we propose an improved PV generation systems. Improved systems for temperature and humidity controlled heating and air conditioning offers a pleasant environment within the building, set up chopper and consists of a PWM voltage type inverter. The proposed system is stable modulation for a one-chip microprocessor using the synchronous signal and control signals was treated. The proposed system is a PWM voltage type inverter and phase of the synchronous to the grid voltage to detect the system voltage and inverter output to drive the statue, so surplus power to connection was able to, certain buildings such as buildings or hospitals, temperature and humidity sensor is applied to the good dynamic characteristic could be obtained. In addition, the system was applied to the high power factor and low-frequency harmonics by maintaining the output load and grid to power to be supplied to a stable control could get a good result.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.1
• /
• pp.7-13
• /
• 2002

Almost applications using fuzzy theory are based on the fuzzy inference. However fuzzy inference needs much time in calculation process for the fuzzy system with many input variables or many fuzzy labels defined on each variable. Inference time is dependent on the number of arithmetic Product in computation Process. Especially, the inference time is a primary constraint to fuzzy control applications using microprocessor or PC-based controller. In this paper, a simple fast fuzzy inference algorithm(FFIA), without loss of information, was proposed to reduce the inference time based on the fuzzy system with triangular membership functions in antecedent part of fuzzy rule. The proposed algorithm was induced by using partition of input state space and simple geometrical analysis. By using this scheme, we can take the same effect of the fuzzy rule reduction.

• Journal of KIISE:Computing Practices and Letters
• /
• v.8 no.3
• /
• pp.277-288
• /
• 2002

In this paper, we describe a design and implementation method of a smart card operating system for multi applications. A smart card is the independent computing system and is able to be used in multi applications such as the electronic commerce and the electronic cash. Smart card operation system(SCOS) provides a basis of smart card booting, and controls and manages application programs. SCOS can produce and control a file system to support multi applications in EEPROM, communicate commands and messages with outside devices, process a command, produce a reply message, and provide security functions of file security in EEPROM, and communication security. Therefor, in this paper, we design and implement SCOS system that provides the authentication between a card and a terminal, the session authentication for multi applications, the processing of commands, and the maintenance of the security.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.467-470
• /
• 2009

CAN communication developed for communication between electric control devices in vehicle, was recently applied to automatic braking devices, and can also be applied to field bus for production automation. Recently, field bus is introduced in engine control, etc. for large ship. In this paper, cabin access control system can be implemented, based on CAN communication. The cabin access control system based on CAN communication consists of access control server, embedded system based on ARM9, and micro-controller built-in CAN controller. The access control server can be able to manage overall access control system by accessing with manager. And embedded system adopted ARM9 processor transmits access information of RFID reader controller connected with CAN networks to server, also performs access control. The embedded system can carry CAN frames to server, so it can be used as gateway.

• Journal of Software Assessment and Valuation
• /
• v.17 no.2
• /
• pp.109-116
• /
• 2021

Traditionally, the engineering field has been dominated by face-to-face education focused on experimental practice, but demand for online learning has soared due to the rapid development of IT technology and Internet communication networks and recent changes in the social environment such as COVID-19. In order for efficient online education to be conducted in the engineering field, where the proportion of experimental practice is relatively high compared to other fields, virtual laboratory practice content that can replace actual experimental practice is very necessary. In this study, we developed a line tracer model and a virtual experimental software to simulate it for efficient online learning of microprocessor applications that are essential not only in the electric and electronic field but also in the overall engineering field where IT convergence takes place. In the developed line tracer model, the user can set various hardware parameter values in the desired form and write the software in assembly language or C language to test the operation on the computer. The developed line tracer virtual experimental software has been used in actual classes to verify its operation, and is expected to be an efficient virtual experimental practice tool in online non-face-to-face classes.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.377-385
• /
• 2017

The solar cell need the characteristic interpreting because the solar cell changes greatly according to the isolation, temperature and load in the photovoltaic development. Moreover, to get many energy in photovoltaic development need the position tracking of the sun according to the environment change. Also, The solar cells should be operated at the maximum power point. In this paper, I used microprocessor and sensor and designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and composed an power conversion system with boost converter and voltage source inverter. Used the constant voltage control method for maximum power point tracking in boost converter control and, used the SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control. The result was less then 5% when compared the catalogue of solar cell module and the simulation through a mathematics modelling. The boost rate of boost converter was similar to 167 % with the simulation.