• Journal of the Korea Organic Resources Recycling Association
• /
• v.28 no.1
• /
• pp.83-95
• /
• 2020

The economic issue of the period of return versus investment has emerged to efficiently utilize the thermal energy of public resource recovery facilities using waste and private thermal source facilities using BIO-SRF. Accordingly, the optimum temperature and pressure facilities are required beyond the traditional designed, constructed and operated. In this study, we analyzed current energy output by different heat and pressure model in domestic facilities, and calculated the characteristics of green-house gas emission. In order to, utilize the thermal energy producing facilities using waste and biomass fuel more efficiently, it is temperature and pressure, which will lead to more lucrative investment and return as well.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.34-40
• /
• 2006

For a cooling performance research of the combustor operated in a extreme environment of a high temperature and high pressure, we accomplished a cooling performance analysis. Generally a heat transfer characteristic in cooling passage is known well experimentally and theoretically, however heat flux in the combustion chamber isn't. In this study, fluid flow combined with heat transfer and thermal structural analysis is accomplished about a combustor nozzle. We tried to analyze the cooling performance with a heat transfer characteristic of a gas and coolant side in the view point of quantity on the mass flow rate to be supplied to the cooling channel. And finally, evaluation on the thermal and structural safety of nozzle wall material was accomplished.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.477-482
• /
• 2009

Though rocket nozzle flow is very important to the rocket performance, the direct measurement is very difficult because of high temperature and high pressure gas flow. Then the experiment utilizing the hydraulic analogy has been developed for such a problem. Supersonic flows through an axisymmetric De Laval nozzle of solid rocket motor was simulated in a 2-D sluice-type water-table designed and manufactured utilizing hydraulic analogy. Methods to minimize or account for non-analogous effects in the hydraulic system must be reviewed for the quantitative application of the hydraulic analogy. In this application the water table is inclined slightly, so that gravity acceleration has a small component in the direction of motion, thus compensating for the effect of friction. Flow visualization leads to better understanding of the analogous system. Within the experimental errors, it is shown that the hydraulic analogy can be used as an effective tool for the study of two dimensional isentropic flows of gases in many fields.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.6
• /
• pp.47-55
• /
• 2011

The present paper deals with numerical analysis to investigate the effect of rounded tube on the pressure drop and heat transfer in a compact tubular heat exchanger designed for high temperature and high pressure system. The pressure drop and heat transfer in the tubular heat exchanger greatly depend on the location of rounded tubes. The effect of locations of the rounded tubes was also analyzed. Three different locations which were tube inlet, tube outlet, and inlet&outlet were considered. In this paper, the tube with a rounded inlet&outlet showed the minimum pressure drop with decreased heat transfer while the tube with a rounded outlet showed better characteristics of pressure drop and heat transfer compared with the results of original model.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.1
• /
• pp.21-26
• /
• 2004

Results from PL and Raman spectroscopic analyses of HPHT (high-pressure high-temperature) treated type IIa diamonds are presented, and these spectral characteristics are compared with those of untreated diamonds of similar color and type. We identify a number of significant changes by 325 nm He/Cd laser excitation. Several peaks are removed completely, including H4, H3 system in HPHT treated diamond. The N3 system, however, increased in emission. Also we can find the behaviour of the nitrogen-vacancy related center N-V centers at 575 and 637.1 nm, as observed with 514 nm Ar ion laser excitation. When these centers are present, the FWHM (full width at half maximum) of 637.1 nm luminescence intensities offers a potential means of separating HPHT-treated from untreated type IIa diamonds. The width of 637.1 nm $(N-V)^-$line measured at the position oi half the peak's height are determine to range from 19.8 to $32.1cm^{-1}$ for HPHT treated diamonds.

• Composites Research
• /
• v.28 no.5
• /
• pp.254-259
• /
• 2015

Carbon fiber/aluminum (CF/Al) composites were successfully fabricated without pressure casting using wettability modification of carbon fiber. The wettability of liquid aluminum on carbon fibers was enhanced through electroless plating of copper on carbon fibers. Liquid aluminum was well infiltrated into carbon fiber bundles with Cu coating layer due to low wetting angle, and a lot of pores that existed in CF/Al composite without Cu coating on CF were greatly removed. However, a few tiny pores existed in carbon fiber bundles, which is due to not bad wettability between CF and Al but shrinkage cavity that was generated during cooling of CF/Al composite. The tiny pores could be effectively removed by a subsequent rolling.

• Journal of Hydrogen and New Energy
• /
• v.29 no.5
• /
• pp.473-482
• /
• 2018

To check applicability of recently developed new oxygen carrier for 0.5 MWth chemical looping combustion system, reactivity tests were carried out at high temperature and high pressure conditions. Pressure, temperature, gas velocity, $CH_4$ flow rate, and solid height were considered as operating variables. The new oxygen carrier (N016-R4) showed not only high fuel conversion but also high $CO_2$ selectivity within all the operating conditions in this study. The reactivity of N016-R4 particle was compared with previous oxygen carriers. The N016-R4 particle represented outstanding reactivity among 10 oxygen carriers in terms of fuel conversion and $CO_2$ selectivity.

• Resources Recycling
• /
• v.4 no.3
• /
• pp.32-39
• /
• 1995

Thc purpose of this study is to develop the efficient process for recovering vanadium and nickel from the incineralionash of the oil fly ash. In this paper, the physical and chemical properties of the incineration ash was examined, and theleaching characteristics of the incineration ash were investigated by water leaching and sulEuric acid leaching tcsls. The incinerationash of oil fly ash was mainly consisted of oxldes such as V,09, V,O,, NaVO,, Ni,(VO,)Z, Fe,O,, CaSO,, SiO,.Thc waler leaching showed low extraction of metallic components, while the sulfunc acid lcaching with high temperahlreand pressure increased the extraction of vanadium and nickcl considerably. For instance, the exlraction rates of the metalllccomponents on the sulfuric acid leaching were 99% for V and 45% for Ni at 90$^{\circ}$C with pH 0.5 H,SO,, and were86% for V and 75% far Ni at ZOO"C(64 psi) with pH 1.0 H-SO,. with pH 1.0 H-SO,.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.2
• /
• pp.118-125
• /
• 2019

Metals exposed to high temperature/high pressure/oxidant excess environment of an oxygen excess pre-combustor may undergo rapid oxidation. In this study, the test facility to simulate the high temperature/high pressure/oxidant excess environment was constructed and the oxidation resistance evaluation was carried out for various metal materials. As a result, the discoloration of the metallic materials, the change in the surface roughness and the peeling of the metal surface were observed, and the weight change was also observed. The resulst showed that oxidation-resistant coating of a metal material of the combustor is indispensably required, and the use of XM-19, which has the highest content of Cr and Ni, is expected to provide more structural stability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.44 no.3
• /
• pp.271-276
• /
• 2024

Traditional oil, a depleting resource, accounts for only one-third of the world's oil reserves, so research and cases of utilizing non-traditional oil as a resource are continuously increasing. However, unconventional oil contains bitumen containing solid particles such as sand, and because it is exposed to a high temperature and high pressure environment, deformation can frequently occur in oil pipelines. Therefore, variables such as material, thickness, and angle that can affect the deformation of the oil pipeline were derived and applied to the oil pipeline, and finite element analysis was performed using the Ansys program. As a result of finite element analysis, deformation and maximum load capacity were derived. Afterwards, the same analysis was performed by modeling an optimized oil pipeline by combining the factors with the best deformation resistance and maximum load capacity. As a result of the analysis, the effect of reducing deformation and increasing the maximum load capacity by about 30 % was confirmed, and factors for suppressing deformation when analyzing oil pipelines were derived.