• Korean Journal of Materials Research
• /
• v.29 no.8
• /
• pp.463-468
• /
• 2019

The electrical and interfacial properties of $HfO_2/Al_2O_3$ and $Al_2O_3/HfO_2$ dielectrics on AlN/p-Ge interface prepared by thermal atomic layer deposition are investigated by capacitance-voltage(C-V) and current-voltage(I-V) measurements. In the C-V measurements, humps related to mid-gap states are observed when the ac frequency is below 100 kHz, revealing lower mid-gap states for the $HfO_2/Al_2O_3$ sample. Higher frequency dispersion in the inversion region is observed for the $Al_2O_3/HfO_2$ sample, indicating the presence of slow interface states A higher interface trap density calculated from the high-low frequency method is observed for the $Al_2O_3/HfO_2$ sample. The parallel conductance method, applied to the accumulation region, shows border traps at 0.3~0.32 eV for the $Al_2O_3/HfO_2$ sample, which are not observed for the $Al_2O_3/HfO_2$ sample. I-V measurements show a reduction of leakage current of about three orders of magnitude for the $HfO_2/Al_2O_3$ sample. Using the Fowler-Nordheim emission, the barrier height is calculated and found to be about 1.08 eV for the $HfO_2/Al_2O_3$ sample. Based on these results, it is suggested that $HfO_2/Al_2O_3$ is a better dielectric stack than $Al_2O_3/HfO_2$ on AlN/p-Ge interface.

• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.33-40
• /
• 1987

The investigation includes phase equilibria of Al2O3-HfO2 Cr2O3-ZrO2, Cr2O3-HfO2, Al2O3-Cr2O3-ZrO2, Al2O3-Cr2O3-HfO2, Al2O3-ZrO2-HfO2, Cr2O3-ZrO2-HfO2, Al2O3-Cr2O3-ZrO2-HfO2. In the systems the solubility near the end members has been studied at 1500$^{\circ}C$ and 1600$^{\circ}C$, respectively. Selective Compositions were investigated in the area of the guarternary system where the phae relation was examined.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.382-382
• /
• 2010

The etch characteristics of the $HfAlO_3$ thin films and selectivity of $HfAlO_3$ to $SiO_2$ in $Cl_2/BCl_3$/Ar plasma were investigated in this work. The maximum etch rate was 108.7 nm/min and selectivity of $HfAlO_3$ to $SiO_2$ was 1.11 at $Cl_2$(3sccm)/$BCl_3$(4sccm)/Ar(16sccm), RF power of 500 W, DC-bias voltage of - 100 V, process pressure of 1 Pa and substrate temperature of $40^{\circ}C$. As increasing RF power and DC-bias voltage, etch rates of the $HfAlO_3$ thin films increased. Whereas as decreasing of the process pressure, those of the $HfAlO_3$ thin films were increased. The chemical reaction on the surface of the etched the $HfAlO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.304.2-304.2
• /
• 2016

Hafnium oxide-aluminum oxide (HfO2-Al2O3) dielectric films have been fabricated by Pulsed Laser Deposition (PLD), and their properties are studied in comparison with HfO2 films. As a gate dielectric of the TFT, in spite of its high dielectric constant, HfO2 has a small energy band gap and microcrystalline structure with rough surface characteristics. When fabricated by the device, it has the drawback of generating a high leakage current. In this study, the HfAlO films was obtained by Pulsed Laser Deposition with HfO2-Al2O3 target(chemical composition of (HfO2)86wt%(Al2O3)14wt%). The characteristics of the thin Film have been investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The X-ray diffraction studies confirmed that the HfAlO has amorphous structure. The RMS value can be compared to the surface roughness via AFM analysis, it showed HfAlO thin Film has more lower properties than HfO2. The energy band gap (Eg) deduced by spectroscopic ellipsometer was increased. HfAlO films was expected to improved the interface quality between channel and gate insulator. Apply to an oxide thin Film Transistors, HfAlO may help improve the properties of device.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.3
• /
• pp.164-169
• /
• 2014

We investigated the etching characteristics of $HfAlO_3$ thin films in $O_2/Cl_2/Ar$ and $O_2/BCl_3/Ar$ gas, using a high-density plasma (HDP) system. The etch rates of the $HfAlO_3$ thin film obtained were 30.1 nm/min and 36 nm/min in the $O_2/Cl_2/Ar$ (3:4:16 sccm) and $O_2/BCl_3/Ar$ (3:4:16 sccm) gas mixtures, respectively. At the same time, the etch rate was measured as a function of the etching parameter, namely as the process pressure. The chemical states on the surface of the etched $HfAlO_3$ thin films were investigated by X-ray photoelectron spectroscopy. Auger electron spectroscopy was used for elemental analysis on the surface of the etched $HfAlO_3$ thin films. These surface analyses confirm that the surface of the etched $HfAlO_3$ thin film is formed with nonvolatile by-product. Also, Cl-O can protect the sidewall due to additional $O_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.924-928
• /
• 2010

In this study, $HfAlO_3$ thin films using gate insulator of MOSFET were etched in inductively coupled plasma. The etch characteristics of the $HfAlO_3$ thin films has been investigated by varying $O_2/BCl_3$/Ar gas mixing ratio, a RF power, a DC bias voltage and a process pressure. As the $O_2$ concentration increases further, $HfAlO_3$ was redeposited. As increasing RF power and DC bias voltage, etch rates of the $HfAlO_3$ thin films increased. Whereas, as decreasing of the process pressure, etch rates of the $HfAlO_3$ thin films increased. The chemical reaction on the surface of the etched the $HfAlO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS). These peaks moved a binding energy. This chemical shift indicates that there are chemical reactions between the $HfAlO_3$ thin films and radicals and the resulting etch by-products remain on the surface.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.4
• /
• pp.166-169
• /
• 2010

In this study, we changed the etch parameters (gas mixing ratio, radio frequency [RF] power, direct current [DC]-bias voltage, and process pressure) and then monitored the effect on the $HfAlO_3$ thin film etch rate and the selectivity with $SiO_2$. A maximum etch rate of 108.7 nm/min was obtained in $Cl_2$ (3 sccm)/$BCl_3$ (4 sccm)/Ar (16 sccm) plasma. The etch selectivity of $HfAlO_3$ to $SiO_2$ reached 1.11. As the RF power and the DC-bias voltage increased, the etch rate of the $HfAlO_3$ thin film increased. As the process pressure increased, the etch rate of the $HfAlO_3$ thin films increased. The chemical state of the etched surfaces was investigated with X-ray photoelectron spectroscopy. According to the results, the etching of $HfAlO_3$ thin film follows the ion-assisted chemical etching.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.129-130
• /
• 2009

The P/E characteristics of $HfO_2$ CTF memory capacitor with $SiO_2/HfO_2/Al_2O_3$(OHA) engineered tunnel barrier were investigated. After a growth of thermal oxide with a thickness of 2 nm, 1 nm $HfO_2$ and 3 $Al_2O_3$ layers were deposited by atomic layer deposition (ALD) system. The band offset was calculated by analysis of conduction mechanisms through Fowler-Nordheim (FN) plot and Direct Tunneling (DT) plot. Moreover the PIE characteristics of $HfO_2$ CTF memory capacitor with OHA tunnel barrier was presented.

• Korean Journal of Metals and Materials
• /
• v.48 no.3
• /
• pp.256-261
• /
• 2010

In this work, high-k dielectric stacks of $HfO_2$ and $HfO_2$/$Al_2O_3$/$HfO_2$ (HAH) were deposited on $SiO_2/Si$ substrates by atomic layer deposition as charge trapping layers in charge trapping devices. The structural stability and the charge trapping characteristics of such stacks were investigated using Metal-Alumina-Hafnia-Oxide-Silicon (MAHOS) structure. The surface roughness of $HfO_2$ was stable up to 11 nm with the insertion of 0.2 nm thick $Al_2O_3$. The effect of the thickness of the HAH stack and the thickness of intermediate $Al_2O_3$ on charge trapping characteristics were investigated for MAHOS structure under various gate bias pulse with duration of 100 ms. The threshold voltage shift after programming and erase showed that the memory window was increased with increasing bias on gate. However, the programming window was independent of the thickness of HAH charge trapping layers. When the thickness of $Al_2O_3$insertion increased from 0.2 nm to 1 nm, the erase window was decreased without change in the programming window.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.315-320
• /
• 2002

Treatment effects of dilute hydrofluoric acid (6 wt% HF) on the surface properties of $Al(OH)_3$ were investigated at the molar ratio of F/Al(fluoride/aluminum)=0.15. Temperature and pH variations in the reaction system were recorded to analyze reaction mechanism between $Al(OH)_3$ and aqueous Hf. The reaction of HF to the surface of $Al(OH)_3$ accompanied with a quantity of heat evolution, resulting in increasing temperature of a reactionsystem. And also the reaction was proceeded as transitional state which metastable ${\alpha}-form\;AlF_3{\cdot}3H_2O$ was transferred to insoluble ${\beta}$-form. The resulting ${\beta}-form\;AlF_3{\cdot}3H_2O$ formed by a surface treatment was identified by FT-IR and X-ray diffractormetry. The formation of ${\beta}$-form aluminum fluoride hydrates with diameter less than $1{\mu}m$ on the surface of $Al(OH)_3$ could be visulaized by SEM imgae, making up a coating layer as precipitate-like. The surface whiteness of $Al(OH)_3$ treated with aqueous HF was furthermore increased approximately 6.6% due to the formation of surface hydrates.