• 대한전자공학회논문지
• /
• 제14권1호
• /
• pp.5-14
• /
• 1977

공기중의 열처리에 의하여 상온에서 낮은 저항을 갖는 PTC 써미스터를 제작했다. 재현성을 높이기 위해 BaTiO3에 Al2O3, SiO2 및 TiO2를 첨가 했으며, 불순물로서 Sb2O3를 첨가했다. 시편은 공기 중에서 1,200℃∼1,380℃로서 가열되었으며, Sb2O3첨가량에 대한 저항관계를 조사했다. 이 시편들은 공기중의 열처리에서도 재현성이 좋았다. 연구된 시편은 3.75mole% Al2O3, 1.25mole% SiO2, 2.25mole% TiO2 및 0.16∼0.25wt% Sb2O3를 BaTiO3에 첨가하여 만들었으며 저항값은 14∼300ohm이었다.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.552-560
• /
• 1994

A composite of TiB2-Al2O3 system was successfully prepared from a mixture of TiO2, B2O3, and Al by self-propagating high temperature synthesis (SHS) with a novel characteristic, utilizing the internal oxidation heat of aluminium metal of the mixture, instead of by a conventional technique, externally heating a mixture of Ti, B and Al2O3. From a mixture with B/Ti molar ratio of =2.0, pure two phases of TiB2 and $\alpha$-Al2O3 with good crystallinity and small, uniform sizes were formed. However, when the B/Ti molar ratio of the mixture goes to a value less than 2.0, in addition to the above main minerals, a small smounts of metastable phases such as TiB and Ti3B4 were formed. It was found that about 60%, the optimum green density of compacts gave their highest reaction rate and temperature during SHS process. TiB2-Al2O3 system composite with B/Ti molar ratio of =2.0 could be pressurelessly sintered even at 190$0^{\circ}C$ under Ar gas flows without any addition of sintering aids, showing their good properties such as 91.2% in relative density, 2750 kgf/$\textrm{mm}^2$ in Vickers hardness and 2620 kgf/$\textrm{cm}^2$ in flexural strength.

• 대한기계학회논문집
• /
• 제17권10호
• /
• pp.2498-2508
• /
• 1993

$Al/SiC/Al_{2}O_{3}$ hybrid composites are fabricated by squeeze infiltration method. From the misconstructive of $Al/SiC/Al_{2}O_{3}$ hybrid composites fabricated by squeeze infiltration method, uniform distribution of reinforcements and good bondings are found. Hardness value of $Al/SiC/Al_{2}O_{3}$ hybrid composites increases linearly with the volume fraction of reinforcement because SiC whisker and $Al_{2}$O$_{3}$ fiber have an outstanding hardness. Optimal aging conditions are obtained by examining the hardness of $Al/SiC/Al_{2}O_{3}$ hybrid composites with different aging time. Tensile properties such as Young's modulus and ultimate tensile strength are improved up to 30% and 40% by the addition of reinforcements, respectively. Failure mode of $Al/SiC/Al_{2}O_{3}$ hybrid composites is ductile on microstructural level. Through the abrasive wear test and wear surface analysis, wear behaviour and mechanism of 6061 aluminum and $Al/SiC/Al_{2}O_{3}$ hybrid composites are characterized under various testing conditions. The addition of SiC whisker to $Al/SiC/Al_{2}O_{3}$ composites gives rise to improvement of the wear resistance. The wear resistance of $Al/SiC/Al_{2}O_{3}$ hybrid composites is superior to that of Al/SiC composites. The wear mechanism of aluminum alloy is mainly abrasive wear at low speed range and adhesive and melt wear at high speed range. In contrast, that of $Al/SiC/Al_{2}O_{3}$ hybrid composites is abrasive wear at all speed range, but severe wear when counter material is stainless steel. As the testing temperature increases, wear loss of aluminum alloy decreases because the matrix is getting more ductile, but that of $Al/SiC/Al_{2}O_{3}$ hybrid composites is hardly varied. Oil lubricant is more effective to reduce the wear loss of aluminum alloy and $Al/SiC/Al_{2}O_{3}$ hybrid composites at high speed range.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.127-135
• /
• 1992

It has been reported that natural petalite showed a low negative thermal coefficient and wide coefficient and wide coexisting region with liquid phase in Li2O-Al2O3-SiO2 system. Therefore, we investigated variation of microstructure and thermal and mechanical properties when the amount of SiO2 content in petalite compound and MgO addition to it compound were changed. As SiO2 content exceeded 80 wt%, crystal phases of $\beta$-cristobalite and $\beta$-spondumene solid solution were formed. Generally, the densification and bending strength were increased by the addition of MgO, but the positive thermal coefficient was found in the case of MgO 10 wt% addition because of second phase and glassy phase.

• 한국결정성장학회지
• /
• 제8권4호
• /
• pp.634-639
• /
• 1998

$Y_2O_3$와 $Nb_2O_5$가 첨가된 지르코니아에 입자 크기가 다른 두종류의 Al2O3를 부피비로 10~30% 첨가한 복합체를 155$0^{\circ}C$ 온도에서 5시간 소결하여 $250^{\circ}C$ 온도의 공기 분위기하에서 1000시간 혹은 $180^{\circ}C$ 온도의 0.3MPa H2O vapor pressure 분위기하에서 5시간 열처리를 하여 X-ray 회절분석 방법을 이용하여 저온 상안정성을 조사하였다. 복합체 전부 열처리 후에 정방정 상에서 단사정 상으로 상전이가 발생하지 않는 우수한 저온 상안정성이 관찰되었다. 복합체의 상아정성에 Nb 첨가가 $Al_2O_3$의 첨가보다 더 효과적이었다. 2.8$\mu$m 입자크기를 가진 Al2O3를 부피비로 20% 첨가한 복합체에서 최적의 조건이 관찰되었으며 강도와 인성값은 각각 670MPa와 7.1MPam1/2이었다. Al2O3 입자 크기가 2.8$\mu$m에서 0.2$\mu$m로 감소함에 따라 강도는 다소 증가하였으나 파괴인성값은 감소하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권11호
• /
• pp.505-513
• /
• 2006

The present study investigated the influence of the content of $Al_2O_3+Y_2O_3$ sintering additives on the microstructure, mechanical and electrical properties of the pressureless-sintered $SiC-ZrB_2$ electroconductive ceramic composites. Phase analysis of composites by XRD revealed mostly of ${\alpha}-SiC(4H),\;ZrB_2,\;{\beta}-SiC(15R)$ and In Situ $YAG(Al_5Y_3O_{12})$. The relative density and the flexural strength showed the highest value of 86.8[%] and 203[Mpa] for $SiC-ZrB_2$ composite with an addition of 8[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid at room temperature respectively. Owing to crack deflection and crack bridging of fracture toughness mechanism, the fracture toughness showed 3.7 and $3.6[MPa{\cdot}m^{1/2}]\;for\;SiC-ZrB_2$ composites with an addition of 8 and 12[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid at room temperature respectively. Abnormal grain growth takes place during phase transformation from ${\beta}-SiC\;into\;{\alpha}-SiC$ was correlated with In Situ YAG phase by reaction between $Al_2O_3\;and\;Y_2O_3$ additives during sintering. The electrical resistivity showed the lowest value of $6.5{\times}10^{-3}[({\Omega}{\cdot}cm]$ for the $SiC-ZrB_2$ composite with an addition of 8[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid at room temperature. The electrical resistivity of the $SiC-ZrB_2$ composites was all positive temperature coefficient(PTCR) in the temperature ranges from $25[^{\circ}C]\;to\;700[^{\circ}C]$. The resistance temperature coefficient showed the highest value of $3.53{\times}10^{-3}/[^{\circ}C]\;for\;SiC-ZrB_2$ composite with an addition of 8[wt%] $Al_2O_3+Y_2O_3$ as a sintering aid in the temperature ranges from $25[^{\circ}C]\;to\;700[^{\circ}C]$. In this paper, it is convinced that ${\beta}-SiC$ based electroconductive ceramic composites for heaters or ignitors can be manufactured by pressureless sintering.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.968-980
• /
• 1995

Al/Al$_{2}$O$_{3}$/C hybrid metal matrix composites are fabricated by the direct squeeze infiltration method. From the microstructure of Al/Al$_{2}$O$_{3}$/C composites, uniform distribution of reinforcements and good bondings are found. Optimum processing conditions for preforms and squeeze castings are suggested. Mechanical properties, such as elastic modulus, elongation, 0.2% offset yield strength and ultimate tensile strength are obtained. Through the abrasive were test and wear surface analsis, wear behavior and its mechanism of AC2B aluminum and Al/Al$_{2}$O$_{3}$/C composites can be characterized under various sliding speed conditions. Tensile strenght elongation of Al/Al$_{2}$O$_{3}$/C composites are decreased with increasing the addition of carbon fiber. On the contrary, elastic modulus of Al/Al$_{2}$O$_{3}$/C composites is slightly improved compared with that of the unreinforced matrix alloy. The addition of carbon fiber to al/al$_{2}$O$_{3}$/C composites gives rise to improvement of the wear resistance. Specially, carbon chopped fibers play an important role in interfering sticking between the counter material and metal matirix composites. Al/Al$_{2}$O$_{3}$/C composites are suitable to high speed due to solid lubication of carbon. And wear model of Al/Al$_{2}$O$_{3}$/C composites is suggested by the examination of worn surfaces.

• 한국세라믹학회지
• /
• 제37권4호
• /
• pp.354-358
• /
• 2000

Tetragonal (t)-ZrO2/Al2O3 composites doped with Y2O3, Nb2O5, and Fe2O3 ((Y, Nb, Fe)-TZP/Al2O3) were prepared over the range containing Fe2O3 from 0.1 to 0.5 mol% with 0.1 mol% intervals to evaluate the effect of Fe2O3 addition on chromaticity, hydrothermal stability, and mechanical property of the composites. After autoclaving for 20 h at 18$0^{\circ}C$ under 3.5 MPa water vapor pressure, no tlongrightarrowm phase transformation was observed probably due to the preferential solid solubility of Fe2O3 in Al2O3, the presence of the rigid Al2O3 particles, and the inherent phase stability of (Y, Nb)-TZP. The optimized strength and the fracture toughness of the composite were 700 MPa and 8.5 MPa.m1/2, respectively, when 0.1 mol% Fe2O3 was added. The composites have shown a gradual color change from a slightly white ivory to a pale yellowish brown with increasing the Fe2O3 concentration.

• 공업화학
• /
• 제16권1호
• /
• pp.45-51
• /
• 2005

Aluminum nitrate 수용액을 원료로 사용하여 $K_2O-Li_2O-Al_2O_3$ 3성분계로부터 $K^+-{\beta}^{{\prime}{\prime}}-Al_2O_3$를 합성하였다. 순수한 $K^+-{\beta}^{{\prime}{\prime}}-Al_2O_3$의 합성을 위하여 원료물질은 $0.84K_2O{\cdot}0.082Li_2O{\cdot}5.2Al_2O_3$의 조성으로 액상상태에서 혼합되었다. 입자크기를 최소화하고 순수한 $K^+-{\beta}^{{\prime}{\prime}}-Al_2O_3$를 합성하는데 있어서 분산첨가제와 용액의 pH의 영향을 조사하였다. 분산첨가제로써 에탄올을 0.0~4.0 M 첨가하였고 용액의 pH는 $NH_4OH$ 수용액과 $HNO_3$를 이용하여 조절하였다. 시료는 pH 1.0에서 7.5까지 0.5 간격으로 수집하였다. 각 시료들은 $1200^{\circ}C$에서 2 h 동안 하소한 후 XRD와 PSA 분석을 하였다. 용액의 pH는 입자크기와 상형성에 모두 중요한 영향을 미친 반면, 에탄올의 첨가는 입자크기에만 영향을 주었다. pH 조절에 $HNO_3$를 사용하였을 경우, $HNO_3$를 사용하지 않았을 때 보다 순수한 $K^+-{\beta}^{{\prime}{\prime}}-Al_2O_3$ 상을 합성하는데 유리함을 알 수 있었다.

• 자원리싸이클링
• /
• 제15권2호
• /
• pp.3-9
• /
• 2006

용융전로슬래그로부터 일반 포틀랜드 시멘트로의 전환에 관한 기초 연구의 일환으로, 전로슬래그의 $Al_{2}O_{3}$ 농도에 따를 고체 CaO 입자와 용융슬래그간의 계면반응을 알아보고자 하였다. 염기도($B=CaO/SiO_2$)를 1과 2로 조정한 전로슬래그에 소정의 $SiO_2$와 $5{\sim}15wt%\;Al_{2}O_{3}$를 첨가제로 첨가하여 MgO도가니에 넣고 $1500^{\circ}C$에서 30분간 가열 용해하여 균질화 한 후, 같은 온도의 소결 CaO펠렛을 투입하여 $10{\sim}30$분간 반응시켰다. 반응 후 급냉한 시편을 도가니의 직경방항으로 절단해서 펠렛 단면의 CaO직경 변화를 측정하여 슬래그중 $Al_{2}O_{3}$첨가에 따른 CaO의 용해속도를 조사하고, 계면 생성층을 SEM/EDX로 관찰하였다. 그 결과, 슬래그의 염기도가 2인 경우, 염기도가 1인 경우 보다 생성층 $C_{3}S$상의 두께는 $Al_{2}O_{3}$를 15wt.%까지 첨가함에 따라 3.5배 증가하였으며, $C_{6}AF_{2}$ 또는 $C_{4}AF$양도 2배 정도 증가됨을 알 수 있었다.