This study described the effect of the multiple injections and diesel-ethanol on the NVH, combustion and emission characteristics of 4 cylinder common rail diesel engine. In order to investigate the influence of diesel-ethanol blended fuel in a light-duty common rail diesel engine, the injection strategy was varied with pilot injection, double pilot injections, and one main injection at various operating conditions. The results showed that diesel-ethanol blended fuel had longer ignition delay than that of the ultra low diesel fuel(ULSD). Also, in the case of multiple injections, the combustion pressure is increased smoothly near the TDC and the NVH are decreased. In the emission characteristics, diesel-ethanol blended fuel produced lower indicated specific nitrogen oxides(IS-NOX) and indicated specific Soot(IS-soot) emissions, however, indicated specific unburned hydrocarbon(IS-HC) and indicated specific carbon monoxide(IS-CO) emissions are slightly increased.

This study investigates experimentally evaporation characteristics of nanofluid droplets containing 50 nm alumina($Al_2O_3$) particles and the wettability changes on a hydrophilic glass surfaces. From the captured digital images by using a CMOS camera and a magnifying lens, we examined the effect of particle concentration on droplet evaporation rate which can be indirectly deduced from the measured droplet volumes varying with time. In particular, with the use of a digital image analysis technique, the present study measured droplet perimeters and the contact angles to study the wetting dynamics during evaporating process. In addition, we compared the measured total evaporation time with theoretically estimated values. It was found that as the volume fractions of nanofluid increased, the total evaporation time and the initial contact angles decreased, while the droplet perimeters increased.

The present study conducts experimental investigation on spreading and deposition characteristics of a $4.3{\mu}l$ de-ionized (DI) water droplet impacting upon aluminum (Al 6061) flat and textured surfaces. The micro-textured surface consisted the micro-hole arrays (hole diameter: $125{\mu}m$, hole depth: $125{\mu}m$) fabricated by the conventional micro-computer numerical control (${\mu}$-CNC) milling machine process. We examined the surface effect of texture area fraction ${\varphi}_s$ ranging from 0 to 0.57 and impact velocity of droplet ranging from 0.40 m/s to 1.45 m/s on spreading and deposition characteristics from captured images. We used a high-speed camera to capture sequential images for investigate spreading characteristics and the image sensor to capture image of final equilibrium deposition droplet for analyze spreading diameter and contact angle. We found that the deposition droplet on textured surfaces have different wetting states. When the impact velocity is low, the non-wetting state partially exists, whereas over 0.64 m/s of impact velocity, totally wetting state is more prominent due to the increase kinetic energy of impinging droplet.

Inkjet printing is one of the direct writing technologies and is able to form a pattern onto substrate by dispensing droplets in desired position. Also, by inkjet technology manufacturing time and production costs can be reduced, and procedures can be more efficient. To form a metal pattern, it must be harmonized with conductive nano ink, printing process, sintering, and surface treatment. In this study, micro patterning of conductive line has been investigated using the piezoelectric printhead driven by a bipolar voltage signal is used to dispense $20-40{\mu}m$ diameter droplets and silver nano ink which consists of 50 nm silver particles. In addition, hydrophobic treatment of surface, overlap printing techniques, and sintering conditions with changing temperature and times to achieve higher conductivity.

In this paper an experimental study is presented to investigate the effect of a step edge and a stationary droplet on the dynamic behavior of impacting droplet on a wall. The main parameters are the distance from the edge and the center-to-center distance between two droplets. Photographic images are presented to show coalescence dynamics, shape evolution and contact line movement. The emphasis is on presenting the spreading length of droplet for the step edge and two coalescing droplets along their original centers. It is clarified that the droplet exhibits much different dynamic behavior depending on the location of the step edge. The momentum of impacting droplet was better transferred to the stationary droplet as the center- to-center distance between two droplets was reduced, which results in more spreading of coalescing droplet.

To improve the mixing and atomizing performance at the center region of the conventional coaxial shear injector spray, the concept of a coaxial porous injector was invented. This novel injection concept for liquid rocket engines utilizes the Taylor-Culick flow in the cylindrical porous tube. The 2-dimensional injector, which can be converted in three injection configurations, was fabricated, and several cold flow tests using water-air simulant propellant was performed. The hydraulic characteristics and the effects of a gas flow condition on the spray pattern and the Sauter mean diameter (SMD) was analyzed for each configuration. The atomizing mechanism of coaxial porous injector was different with the coaxial shear injector, and it was explained by the momentum of the gas jet, which is injected normally against the center liquid column, and by the secondary disintegration at the wavy interface of liquid jet, which was generated at the recessed region. The SMD of 2D coaxial porous injector, which has higher gas momentum, was measured and it shows better atomizing performance at the center and outer side of spray than the 2D coaxial shear injector.