The characteristics of fretting wear are reviewed. Fretting damage depends on slip amplitude and classified into three groups: (1) an annular damage according to Mindlin's analysis at microslip region, (2) strong adhesive deformation without loose wear particles at the intermediate region, and (3) formation of fine oxide particles at the gross slip region. The critical slip amplitude of fretting is the boundary between (2) and (3). The boundary slip amplitude depends on normal load. The wear rate increases and saturates with increasing slip amplitude. But it is constant by considering the critical amplitude. The role of oxide particles are discussed. Three different actions are noted: accelerating wear, preventing wear and insignificant effect. The oxide shows two opposing effect depends on normal load and slip amplitude. This is related to the removal rate from the interface (abrasive action) and compaction rate at the interface to form a protective layer. The effect of oxidation is significant to determine the wear and friction. The diffusion of oxygen is restricted at the small amplitude. As a result, crack formation at the boundary is a predominant damage, related to fretting fatigue damage.

Rapid increase of refrigeration & air-conditioning system( r & a system ) in modern industries brings attention to the urgency of development as a core technology in the area. And it required to the compatibility problem of r & a system to alternative refrigerant for the protection of environment. Then, it is requested to research about the lubrication characteristics of refrigerant compressor which is the core thechnology in the r & a system. The study of lubrication characteristics in the critical sliding component is essential for the design of refrigerant compressor. Therefore, theoetical investigation of the lubrication characteristics of rotary compressor for r & a system is studied. And the Runge-Kutta method is used for the analysis of the behavior of rolling piston in the rotary compressor. The results show that the rotating speed of shaft and the discharge pressure have an important effect upon the angular velocity of the rolling piston. This results give important basic data for the further lubrication analysis and design of the rotary compressor.

Gerotor Pump and Motors are widely used in lubrication and hydraulic actuator systems, These have many advantage compared with internal gear pump and motors, But the gerotor profile have not been sufficiently analyzed theoretically. So it is vary difficult for designer to decide the specifications of the gerotor profile, and it is not yet confirmed to calculating flow rate and minimum distance of clearance in the contact point of inner and outer rotor. In this paper, When we design inner and outer rotor concurently, We have analyzed the gerotor and displayed the calculated results such as flow rate, minumum distance between inner and outer rotor and gerotor profiles

본 연구에서는 베어링 하우징의 탄성 변형을 고려한 커넥팅 로드 베어링의 탄성 유체 윤활 해석을 통해 축 중심의 궤적, 최소 유막 두께 변화, 최대 유막 압력 변화를 예측하였다. 베어링 하우징의 탄성 변형을 고려한 해석 결과 강체 해석 결과보다 축의 편심율과 최소 유막 두께는 크게, 최대 유막 압력은 낮게 예측되었다. 또 축의 회전 속도가 증가할수록, 실린더 압력이 증가할수록 최소 유막 두께는 감소하였다.

An elastohydrodynamic lubrication (EHL) analysis for an axially crown profiled cylindrical roller is carried out using a finite difference method and the Newton-Raphson method. Variations of the minimum film thickness with dimensionless parameters show considerably different from those of infinite solutions.

A numerical analysis is performed about the static and dynamic characteristics of the oil-lubricated herringbone-grooved journal bearing which has circular groove profile. Some tests of jitter and W/F measurements are carried out to verify the performance of the newly designed drum assembly.

For a vertical type crankshaft-journal bearing system used in scroll compressor, nonlinear transient response analysis is applied includung nonlinear fluid film reaction forces of journal beatings. By a connected behavior analysis of crankshaft and orbiting scroll, the radial clearance of scroll wraps is calculated. Considering tangential leakage for this clearance, a coupled analysis model for leakage and dynamic behavior of the orbiting scroll is made, and analyzed by iterative calculation. By regarding clearances of main, sub bearing of crankshaft and orbiting scroll shaft bearing clearance as design parameters, the radial clearance of scroll wraps is analyzed.

본 연구에서는 각종 강구조물의 도장전 샌드블리스트 작업에 다른 공해를 방지하기 위해, 모래-물의 2상류를 분사할 수 있는 샌드블라스트 장치를 제작하여, 2상류 분사에 따른 마멸-부식(wear-corrosion)특성과 slurry erosion에 의한 anchor pattern 및 침식-마멸거동을 고찰하고, 물에 의한 강구조물의 부식방지를 위한 부식억제제가 강구조물의 도막에 미치는 방식특성을 구명함으로써 공해방지, 부식손상 및 산업의 국제경쟁력 향상에 기여하고자 한다.

The new trends in main spindle design of Machining Center are focused on high-speed, high-precision and high-stiffness. As a main spindle bearing, the angular-contact ball bearing is well used. A rolling bearing is usually only a small part of a larger mechanical system, but its performance can have a great influence on the functioning of the whole machine. This work is about fatigue life tester design and monitoring of defected rolling-element bearings. The major work is done via experiments and the vibration signal is analysised by means of frequency spectrum technique. By analyzing the frequency spectrum, it is possible to view the condition of the bearings.

일반적으로 미모시험의 목적은 재료의 내마모성을 평가하는데 있다고 할 수 있다. 그러나 마모시험의 결과는 재료의 성질에만 연관된 재료 고유의 성질이 아니기 때문에 시험기의 형상과 시험편의 접촉모드, 시험분위기 등의 재료외적인 인자들에 의해 상당히 영향을 받는 것으로 알려져 있다. 따라서 재료의 내마모성을 평가하기 위해서는 그 재료가 쓰이고 있는 실제 상황에서 시럼을 하는 것이 가장 좋은 것이지만 실제 상황에서 시험을 하기가 어려운 경우가 대부분이므로 모사실험의 방법이 많이 이용되고 있다. 그러나 모사실험의 경우에는 시험결과의 신뢰성이 매우 중요한 요소가 되며 이러한 신뢰성의 구축이 실험결과 못지않게 중요하다고 할 수 있다. 하지만 현재의 마모시험 데이터는 대부분 특정 연구실에서 특정 시험기로 평가한 것이 주류를 이루고 있어 위의 요구사항을 충족시키지 못하는 실정이다. 따라서 본 연구에서는 마모데이터의 신뢰성을 보장하고, 마모시험의 표준화에 도움이 되고자 마모에 관심이 있는 연구자들이 그룹을 이루어 공동연구를 실시하였다.

This paper was undertaken to analyze the morphology of wear debris generating from moving lubricated machine surfaces by image processing. The lubricating wear test was carried out under different experimental conditions using the wear test device was made in our laboritory and wear testing specimen of the pin on disk type wear rubbed in paraffine series base oil, by varying applied load, sliding distance. The four parameters(50% volumetric diameter, aspect, roundness and reflectivity) to describe the morphology have been developed and are outlined in the paper. A system using such techniques promises to obviate the need for subjective, human interpretation of particle morphology in machine condition monitoring, thus overcoming many of the difficulties with current methods and facilitating wider use of wear particle analysis in machine condition monitoring.

In this study, CrN, TiN and TiN + CrN coatings have treated onto the steel substrates by ion plating to improve their tribological behaviors. Some of the specimens were ion nitriding treated to study the effect of ion nitriding on wear behavior. The wear tests were performed with these specimens by ball-onplate type and disc-on-plate type wear tester. It was demonstrated that ion nitriding treatment improve wear resistance of the coatings. The results of high temperature wear tests indicated that the specimens coated with CrN were exhibited the better wear resistance properties than the specimens with TiN coatings