Generally, printing inks are composed of pigment, vehicle and additive. Among others, the vehicle transfers the pigment to substrate and then binds it on the surface. So, rheological properties of the vehicle are an important factor which has influence on printability. Thus, in this study, rheology of the vehicle was investigated by using rotational rheometer according to molecular weight of resin. Also, emlusion rheology of water in oil type and its microstructure were examined with increasing the shear rate. Consequently, the following results were obtained: (1) By viscometric flow test, zero shear viscosity and shear thinning index of vehicle increased with increasing the molecular weight of resin. (2) By relaxation and creep test, relaxation time and retardation time of vehicle increased with increasing the molecular weight of resin. (3) By frequency sweep test, crossover point of vehicle increased with increasing the molecular weight of resin. (4) G' and G" of emlusions increased with increasing the molecular weight by amplitude sweep test. (5) The shape of water drop in emlusions was changed to the capillary tube.

This analog communication system overcomes a limit of the digital communication that used an electric power line, and shows a strong characteristic by decrease of impedance along a load or surge-voltage and the same noise. this system is to detect an sound signal added to light through an photo-sensor and a filter circuit. And a signal detected in this way is transmitted to sound through a speaker of an earphone again.

Generally, machine calendering are used change of paper surface properties. During machine calendering, dry paper passes between the rolls under pressure, thereby improving the surface smoothness and gloss. These improvements make the paper better suited for printing and decreasing problems during the printing, such as delayed dry and set-off. Then we investigated newspaper properties by the changing of machine calendering condition, and relationship printability. Properties of each samples were examined in accordance with KS and TAPPI standard test method i.e, basic weight, bulk density, thickness, porosity, opacity, brightness, smoothness and roughness. IGT printability tester was used to obtain ink requirement of newspaper, printed density and set-off. Results of in this study, we have proposed the optimizes range of newspaper calendering condition. Useful optimize calendering condition was pressure 55 kN/m, temperature $130^{\circ}C$.

The propose of this study investigated the reproduction of color image displayed on a CRT monitor, for a range of different values of monitor gamma. We have used the GOG(gain-offset-gamma) model of the behavior of the CRT. Color difference have been computed in a color space, based on the CIELAB color appearance model. The 133 patch defined linearly color sample and 24 patch defined printing color target were used, and were subjected to the influence of nine different gamma value. The result show that neutral color is increasing the decrease range of luminance black color than white color. These results are of concern in the context of the "correct" display of color reproduction.

In gravure printing, the amount of ink from cells has a great effect on the qualities of final printed products. And printability of final products is determined by every kinds variables. Ink transfer process is not verified scientifically because gravure cell is of small size and print speed is rapid. Therefore in order to study of ink transfer mechanism, this study is using the Computational Fluid Dynamics Evaluation. Polyflow 3-10 simulation software is used for considering of non-Newtonian flow. Among the various factors, this study have dealt with gravure cell types used computer simulation in order to define distinctive features in ink flow and transfer. The results of simulation, it defined the distribution of pressure, speed, stream function, viscosity, shear rate during the gravure printing. It is fined out the difficulties and characteristics according to the shape of cell types. Through this study, the condition of gravure printing is depending on the print condition and characteristic of cells.

Offset lithography is the most widely used printing process in domestic printing industry, but there are no industry-wide specifications for press control to assure consistent quality across printing plants. As printing becomes more of a commodity and less of an art, it is necessary to develop a print quality specification standard suitable for Korea offset printing field. This study aims to contribute to improving the quality of domestic offset color prints by comparative study on color reproduction properties of 3 kinds of domestic process color ink composed of C(cyan), M(magenta), Y(yellow), and K(black), and of 3 kinds of domestic coated paper, using densitometric color measurement method.

The measured plasma temperature of Ar hollow cathode discharge for several metal cathodes are about $620\;{\sim}\;780K$ at discharge current of $7\;{\sim}\;10mA$. The optogalvanic signals were measured using hollow cathode discharge tube with argon as buffer gas at change of discharge currents. A change of ionization rate due to electron collision causes an increase or decrease of the electric conductivity. This change in electric conductivity generates the optogalvanic signal. We conclude that optogalvanic signal has close relation with the lowest metastable atoms density at low current.

In off-set printing or coating process, it transfers ink on plate by rolling system. As Ink flows between rolls have an influence on printability of the final products, it needs to be studied scientifically and then control its values. Ink flows between rolls are processed under the effect of diversity factors such as rhelogical properties, printing speed, temperature, humidity etc. Therefore, this study try to approach the real ink transfer mechanism to be concerned about all sorts of variables.

Printing inks are basically dispersions of solid pigment particles in a vehicle. Pigment flocculation and/or colloidal aggregates created by thixotrope additives form a three- dimensional network in the inks. This structure complicates the flow behaviour of inks. However, if the internal structure is formed under control, the printing process will benefit from it because the ink must satify rheological requirements over a very wide range of shear conditions. The presence of internal structure results in the following prominent non-Newtonian rheological properties: viscoelasticity, yield stress, shear thinning and thixotropy. If the components of printing inks were changed, the rheological characteristics such as viscosity, yield stress, viscoelasticity and tack value were considerably varied. Thus, in this paper, the effects of changing the content of rosin modified phenolic resin on rheological properties of the vehicle will be studied. For that, the rheological properties were found by flow, yield stress, creep and oscillation measurements using Bohlin C-VOR Rotational Rheometer. And Emulsion rheology and its microstructure will be investigated.

The liquid film behavior between two rotating rollers has been analyzed for many years. Their contributions were, however, limited almost within the areas of polymer laminar flow in there. When the slip contact of two rotating rollers is used as a role of vehicle to distribute the liquid discharged on to each roller after splitting from the nip, there was few available relationship to control the roller speed and to design system. On this work it was possible to get out a certain relationship between the discharged film thickness ratio and the roller surface seeds without any help of pressure limit at the splitting point. The hydrodynamic analyzation of Newtonian liquid behavior around the point was well proved on some manipulative experiment. The thickness ratio increases along with the roll surface speed ratio increases. And the discharged volume flow rate ratio on each roller surface varies with square of the speed ratio. Both of these relationship have a decision factor also made up by the speed ratio.

The printing could not expect the print effect of the specific character of a printing material. Specially, a property of the paper that we are aware of the substrate has controled printability as well as run ability. The objective of this study was to measure substrate properties by measuring the water receptivity in order to know the degree of the uniformity on surface of paper. Therefore, the water receptivity was measured by fluid bridge method. And then the physical properties of samples such as ink set-off, porosity and print mottle of domestic coated papers were measured by Tappi method. Accordingly, this study obtained the outcome of water receptivity. And then we could know that the relations between water receptivity and physical properties of the paper samples have correlations. There are many measurement equipments to find out print mottle by the measurement of the reflected density at this point in time. However, it is thought that the fluid bridge method is the most proper way to find out print mottle, though there are many other ways to figure out.