• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.3
• /
• pp.228-236
• /
• 2022

The charging methods of electric vehicles are divided into wired charging and wireless charging. Restrictions on the use of charging infrastructure for wireless charging vehicles currently exist because most charging infrastructure uses the wired charging method. Thus, wired and wireless integrated charging system has been studied. In this system, a wireless charging system especially requires a control method for high-efficiency operation in consideration of a change in a coupling coefficient. Therefore, this paper introduces two control methods for the high-efficiency operation of wireless charging that can be applied to wired and wireless integrated charging systems. In addition, loss analysis is performed through PSIM simulation to select a more advantageous method for high-efficiency operation among the two control methods. To verify the simulation-based loss analysis result, the two control methods are applied to the actual wireless charging system, and the efficiency is compared through the experiments Based on the experimental results, a control method suitable for high-efficiency operation of the wireless charging method is selected.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.2
• /
• pp.29-33
• /
• 2021

A 5.8-GHz 1W wireless power transmission system was used for charging a smart phone. The voltage of one RF power receiver with antenna was not enough for charging. Several power receivers for charging a smart phone was connected serially. The voltage of several RF power receivers are highly enough for charging a smart phone within 50cm. However, the lack of current from small capacitances of RF-DC converters is not suitable for charging smart phone. It means very long charging time. In this paper, the voltage multiplier circuits for RF-DC converters were analyzed to increase the current and voltage at the same time to reduce the charging time in smartphone RF wireless charging. Through the analysis of multiplier circuits, the 7-stage parallel multiplier circuit with voltage-doubler units are suitable for charging the smartphone, which supplies 5V and 700mA at 3V@5.8GHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.6
• /
• pp.804-808
• /
• 2018

Interest in wireless power transfer (WPT) has been growing recently due to the rapid increase in the use of electronic devices. Wireless charging systems are currently being applied to mobile phones and many studies are being conducted to apply wireless charging systems to various devices. The current wireless charging systems are capable of 1:1 charging. For wireless charging, when the devices with the same resonance frequency are present in the vicinity, the charging efficiency may be significantly lowered due to frequency interference or the wireless charging systems may stop operating. In this paper, variable capacitors were applied to a superconducting WPT system to solve the frequency interference among multiple devices with the same frequency. When a wireless charging system was performing 1:1 operation, the frequency of the other devices was varied using variable capacitors. As a result, it was confirmed that the highly efficient WPT is possible without frequency interference even when multiple receivers are present.

• ETRI Journal
• /
• v.41 no.3
• /
• pp.326-336
• /
• 2019

A wireless power transfer technique can solve the power capacity problem in wireless rechargeable sensor networks (WRSNs). The charging strategy is a wide-spread research problem. In this paper, we propose a demand-based charging strategy (DBCS) for WRSNs. We improved the charging programming in four ways: clustering method, selecting to-be-charged nodes, charging path, and charging schedule. First, we proposed a multipoint improved K-means (MIKmeans) clustering algorithm to balance the energy consumption, which can group nodes based on location, residual energy, and historical contribution. Second, the dynamic selection algorithm for charging nodes (DSACN) was proposed to select on-demand charging nodes. Third, we designed simulated annealing based on performance and efficiency (SABPE) to optimize the charging path for a mobile charging vehicle (MCV) and reduce the charging time. Last, we proposed the DBCS to enhance the efficiency of the MCV. Simulations reveal that the strategy can achieve better performance in terms of reducing the charging path, thus increasing communication effectiveness and residual energy utility.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.3
• /
• pp.136-139
• /
• 2021

In this paper, we studied the charging characteristics of high-capacity supercapacitor with high current for RF wireless charging system for smart phone charging. The dc output of the RF-DC receiver is connected to supercapacitor after which is connected to DC-DC converter for charging a smart phone. This configuration stably supplies voltage and current for charging it. Studies show that the higher charging current use, the rapidly shorter the charging time of supercapacitor is. The currents of 2A, 10A and 27A were used for charging supercapacitors. The charging time was measured for 3000F, 6000F, 12000F supercapacitors which is parallelly connected with 3000F supercapacitors.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.2
• /
• pp.25-28
• /
• 2021

In this paper, we studied smart phone RF wireless charging with 5.8-GHz microwave wireless power receiver. The dc output of the receiver connected to super capacitor and DC-DC converter for charging a smart phone. This configuration stably supplies 5V and current for charging it. Studies show that the more receivers are used at close range, the higher the received voltage values and the larger the capacity of the super capacitor, the longer the charging time. The present 5.8-GHz 1W wireless power transmission system is not enough for charging a smartphone mainly due to the lack of current of the receiver.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.210-213
• /
• 2016

This paper presents a wireless power charging system for rechargeable batteries. Recently, misalignment between transmitting coil and receiving coils has been a significant factor to wireless power charging systems, which are prone to lateral and angular misalignment. Unfortunately, the batteries can be easily rolled because of the shape, and coils are often misaligned while charging devices, in practical situations. This paper presents the wireless power battery charging system. In order to solve the angular misalignment, two perpendicular coil having structure of 'plus (+)' shape was proposed. To validate the results, the proposed wireless power charging system was implemented at 6.78 MHz using loosely coupled resonant coils, and the system was verified as being robust to misalignment.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.7 no.2
• /
• pp.95-101
• /
• 2012

In order to supply emotion service depending on user's emotional change in a mobile environment, various researches have been carried. This paper discusses a protocol for wireless charging and an embedded platform of the mobile emotional sensing device which supports that. Wireless charging process relieves user's vexatious task to charge the emotional sensing device. To support wireless charging, there are one basestation and several mobile devices. Basestation coordinates and controls the devices over wireless communication, as well as supplies energy. For 1:N communication we defines the network whose superframe is classified into four categories: a network join superframe, a charging request superframe, a charging superframe and an inactive superframe. Physical layer provides how to supply energy to the devices and communicate physically. Mobile device is equipped with energy charged circuits, which correspond with the defined energy supplying method, as well as bidirectional communication circuits. Mobile device monitors and analyzes its own battery status, and is able to send a request packet to basestation. Therefore, it can be charged before its battery is exhausted without user's perception.

• Journal of Information Processing Systems
• /
• v.16 no.3
• /
• pp.677-687
• /
• 2020

This paper deals with the electrical shock that can occur in a car wireless charging system. The recently released the Wireless Power Consortium (WPC) standard specifies that the receiver must be protected from the radio power generated by the transmitter and presents two scenarios in which the receiver may be subjected to electrical shock due to the wireless power generated by the transmitter. The WPC also provides a hardware approach for blocking the wireless power generated by the transmitter to protect the receiver in each situation. In addition, it presents the hardware constraints that must be applied to the transmitter and the parameters that must be constrained by the software. In this paper, we analyze the results of the electric shock in the vehicle using the WPC certified transmitter and receiver in the scenarios presented by WPC. As a result, we found that all the scenarios had electrical shocks on the receiver, which could have a significant impact on the receiver circuitry. Therefore, we propose wireless power transfer limit (WPTL) algorithm to protect receiver circuitry in various vehicle charging environments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.678-683
• /
• 2010

This paper presents a wireless (contactless) charging technique with a new core material called permalloy. For charging portable devices wirelessly, ferrosilicon or ferrite has been conventionally used. Due to high permeability of permalloy, charging efficiency can be significantly improved and subsequently this high efficiency increases charging distance between charger and portable devices. Comparative experimental studies demonstrate that the charging performance and efficiency with permalloy employed are significantly improved. The proposed wireless charging techniques can be used to charge portable devices efficiently.