• Journal of Korean Society of Forest Science
• /
• v.96 no.5
• /
• pp.503-509
• /
• 2007

The major objective of this study was to analyze the difference of the chemical characteristics of acid deposition in Quercus forests in Korea and Japan. The pH values of rainfall at the experimental forest of Kangwon National University (KS site) were higher than those at the Foresta Hills in Japan (JP site), and all chemical contents of throughfall and stemflow were much higher than those of rainfall in Quercus forest stands at the KS and JP site. The pH values, $Ca^{2+}$, $NO_3{^-}$ and $SO{_4}^{2-}$ concentration of throughfall and stemflow at the KS site showed seasonal variation. While at the JP site, the same pattern was shown in the pH values of throughfall and stemflow, however, did not show any difference among seasons. Also, the annual input of all nutrients in these two contrasting forests varied seasonally. These results can be used to predict the amounts of air pollutant that are washed off and leached by the rainfall and Yellow Sand (Asian dust), including NOx and SOx acid pollutants transported easterly from China in the spring. Therefore, it is necessary to quantify the inputs of dry and wet deposition throughout a full year to gain a more complete understanding of the effects of acid deposition on the nutrient cycles in these forest ecosystems.

• Economic and Environmental Geology
• /
• v.40 no.6
• /
• pp.771-784
• /
• 2007

This study shows the weathering characteristics of mica-schist affected by faulting and metamorphism through laboratory tests. Frozen-thaw test, which simulate the physical-chemical weathering processes in the laboratory, shows the important influence of foliation developed in mica-schist, resulting in $20{\sim}40%$ reduction of UCS according to weathering grade of rock. Slaking durability test was carried out for different weathering grade rock specimens and indicated that the specimens from fault area had a low durability index compared to other relatively fresh samples. XRD analysis allowed to estimate the dynamic evolution of mineral composition through wet-dry cycle in which the chlorite was the most important mineral leached out during slaking test. The creep test indicated that the main deformation produced along the foliation plane. The compacted clay minerals between discontinuity planes influence on the discontinuity shearing properties and result in a big difference between peak shear strength and residual strength. The results of laboratory tests on mica-schist show the possibility of a important deformation along the foliation plane or discontinuity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1351-1360
• /
• 1993

The fatigue behavior of GFRP composites is affected by environmental parameters. Therefore, we have to study on effect of sea water on fatigue behavior of GFRP composites as to maintain the safety and confidence in design of ocean structure of GFRP. In this paper, we investigated the fatigue properties of chopped strand glass mat/polyester composite in synthetic sea water. (pH 8.2) In case of the glass fiber (CSM type) reinforced polyester composite materials, the fatigue crack in the both dry and wet specimens tested in air or synthetic sea water occurred at the initial of cycle. Thereafter, it was divided with two regions that one decreased with the crack extension and the other increased with the crack extension. The transition point occurred during the crack propagation shifted to high ${\Delta}K$ value as load increase but its point is not changed regardless of immersion or test environment under a constant load. The synthetic sea water degrades the bond strength between fiber and matrix, thereby the tendency of rapid deceleration and acceleration of the crack growth was appeared.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.865-871
• /
• 2012

Because of the increasing cost of oil and natural gas, energy production technologies using coal, including synthetic natural gas (SNG) and integrated gasification combined cycle (IGCC), have attracted attention because of the relatively low cost of coal. During the early stage of a project, the developer or project owner has many options with regard to the selection of a gasifier. In particular, from the viewpoint of feasibility, the gasifier is a key factor in the economic evaluation. This study compares the technical aspects of gasifiers for a real SNG production project in an early stage. A fixed-bed slagging gasifier, wet-type entrained gasifier, and dry-type entrained gasifier, all of which have specific advantages, can be used for the SNG production project. Base on a comparison of the process descriptions and performances of each gasifier, this study presents a selection guideline for a gasifier for an SNG production project that will be beneficial to project developers and EPC (Engineering, Procurement, Construction) contractors.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.151-155
• /
• 2018

Degree of membrane degradation in Proton Exchange Membrane Fuel Cells (PEMFC) is mainly evaluated by the hydrogen crossover current density. The hydrogen crossover current density is measured by linear sweep voltammetry (LSV), which differs from the DOE protocol and the NEDO protocol. In this study, two protocols were compared during PEMFC operation and accelerated stress test. In the LSV method by the DOE method, the scan rate change affects the hydrogen crossover current density, but the NEDO method does not affect the hydrogen crossover current density. In the course of 15,000 cycles of polymer membrane wet/dry cycle, the DOE method was sensitive to membrane degradation, but the NEDO method was less sensitive to membrane degradation than the DOE method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.406-406
• /
• 2010

일반적으로, 나노스케일의 MOS 소자에서는 게이트 절연체 두께가 감소함에 따라 tunneling effect의 증가로 인해 PID (plasma induced damage)로 인한 소자 특성 저하 현상을 감소하는 추세로 알려져 있다. 하지만 요즘 많이 사용되고 있는 high-k 게이트 절연체의 경우에는 오히려 더 많은 charge들이 trapping 되면서 PID가 오히려 더 심각해지는 현상이 나타나고 있다. 이러한 high-k 게이트 식각 시 현재는 주로 Hf-based wet etch나 dry etch가 사용되고 있지만 gate edge 영역에서 high-k 게이트 절연체의 undercut 현상이나 PID에 의한 소자특성 저하가 보고되고 있다. 본 연구에서는 이에 차세대 MOS 소자의 gate stack 구조중 issue화 되고 있는 metal gate 층과 gate dielectric 층의 식각공정에 각각 중성빔 식각과 중성빔 원자층 식각을 적용하여 전기적 손상 없이 원자레벨의 정확한 식각 조절을 해줄 수 있는 새로운 two step 식각 공정에 대한 연구를 진행하였다. 먼저 TiN metal gate 층의 식각을 위해 HBr과 $Cl_2$ 혼합가스를 사용한 중성빔 식각기술을 적용하여 100 eV 이하의 에너지 조건에서 하부층인 $HfO_2$와 거의 무한대의 식각 선택비를 얻었다. 하지만 100 eV 조건에서는 낮은 에너지에 의한 빔 스케터링으로 실제 패턴 식각시 etch foot이 발생되는 현상이 관찰되었으며, 이를 해결하기 위하여 먼저 높은 에너지로 식각을 진행하고 $HfO_2$와의 계면 근처에서 100 eV로 식각을 해주는 two step 방법을 사용하였다. 그 결과 anistropic 하고 하부층에 etch stop된 식각 형상을 관찰할 수 있었다. 다음으로 3.5nm의 매우 얇은 $HfO_2$ gate dielectric 층의 정확한 식각 깊이 조절을 위해 $BCl_3$와 Ar 가스를 이용한 중성빔 원자층 식각기술을 적용하여 $1.2\;{\AA}$/cycle의 단일막 식각 조건을 확립하고 약 30 cycle 공정시 3.5nm 두께의 $HfO_2$ 층이 완벽히 제거됨을 관찰할 수 있었다. 뿐만 아니라, vertical 한 식각 형상 및 향상된 표면 roughness를 transmission electron microscope(TEM)과 atomic force microscope (AFM)으로 관찰할 수 있었다. 이러한 중성빔 식각과 중성빔 원자층 식각기술이 결합된 새로운 gate recess 공정을 실제 MOSFET 소자에 적용하여 기존 식각 방법으로 제작된 소자 결과를 비교해 본 결과 gate leakage current가 약 one order 정도 개선되었음을 확인할 수 있었다.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.308-319
• /
• 2016

In order to set the outdoor weather conditions to be applied to the design standard of the greenhouse heating and cooling system, outdoor air temperature and heating degree-hour for heating design, dry bulb temperature, wet bulb temperature and solar irradiance for cooling design were analyzed and presented. For every region in Korea, we used thirty years from 1981 to 2010 hourly weather data for analysis, which is the current standard of climatological normal provided by KMA. Since the use of standard weather data is limited, design weather conditions were obtained using the entire weather data for 30 years, and the average value of the entire data period was presented as a design standard. The design weather data with exceedance probability of 1, 2.5, and 5% were analyzed by the TAC method, and we presented the distribution map with exceedance probability of 1% for heating and 2.5% for cooling which are recommended by design standards. The changes of maximum heating load, seasonal heating load and maximum cooling load were examined by regions, exceedance probabilities, and setpoint temperatures. The proposed outdoor design conditions can be used not only directly for the greenhouse heating and cooling design, but also for the reinforcement of heating and cooling facilities and the establishment of energy saving measures. Recently, due to the climate change, sweltering heat in summer and abnormal temperature in winter are occurring frequently, so we need to analyze weather data periodically and revise the design standard at least every 10 years cycle.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.4
• /
• pp.411-422
• /
• 2016

Recently, because the wet pool storage facilities of NPPs in Korea has become saturated, there has been much active R&D on an interim dry storage system using a transportation and storage cask. Generally, the shielding evaluation for the design of a spent fuel transportation and storage cask is performed by the design basis fuel, which selects the most conservative fuel among the fuels to be loaded into the cask. However, the loading of actual spent fuel into the transportation metal cask is not limited to the design basis fuel used in the shielding evaluation; the loading feasibility of actual spent fuel is determined by the shielding evaluation that considers the characteristics of the initial enrichment, the maximum burnup and the minimum cooling period. This study describes a shielding analysis method for determining the minimum cooling period of spent fuel that meets the domestic transportation standard of the dual purpose metal cask. In particular, the spent fuel of 3.0~4.5wt% initial enrichment, which has a large amount of release, was evaluated by segmented shielding calculations for efficient improvement of the results. The shielding evaluation revealed that about 81% of generated spent fuel from the domestic nuclear power plants until 2008 could be transported by the dual purpose metal cask. The results of this study will be helpful in establishing a technical basis for developing operating procedures for transportation of the dual purpose metal cask.

• Korean Chemical Engineering Research
• /
• v.59 no.3
• /
• pp.339-344
• /
• 2021

In order to improve the PEMFC (Proton Exchange Membrane Fuel Cell) durability, it is important to accurately evaluate the durability of the membrane in a short time. Recently, DOE (Department of Energy) reported a protocol that combines the chemical and mechanical durability of membranes to evaluate them effectively. This protocol applies chemical/mechanical deterioration to the membrane by repeating wet/dry while OCV (Open Circuit Voltage) holding. The problem of this protocol is that it is highly affected by electrode degradation due to change cycles in OCV and that the evaluation time is long. By using oxygen instead of air as the cathode gas while leaving the other conditions of the DOE protocol as it is, the durability evaluation time could be reduced from 408 hours to 144 hours. By reducing the number of voltage change cycles to 1/3, the electrode degradation due to the voltage change cycle was reduced to 1/12 when oxygen was used compared to air at the end, thereby enabling more accurate evaluation of polymer membrane durability.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.37-46
• /
• 2024

This study investigates the evolution of concrete damage due to chloride-induced steel corrosion through Impact-echo (IE) testing. Three reinforced concrete specimens, each measuring 1500 mm in length, 400 mm in width, and 200 mm in thickness, were fabricated using three concrete mixture proportions of blended cement types: ordinary Portland cement, ground granulated blast-furnace slag and fly ash. Steel corrosion in the concrete was accelerated by impressing a 0.5 A current following a 35-day cycle of wet-and-dry saturation in a 3% NaCl solution. Initial IE data collected during the saturation phase showed no significant changes, indicating that moisture had a minimal impact on IE signals and highlighting the slow progress of corrosion under natural conditions. Post-application of current, however, there was a noticeable decline in both IE peak frequency and the P-wave velocity in the concrete as the duration of the impressed current increased. Remarkably, progressive monitoring of IE proves highly effective in capturing the critical features of steel-corrosion induced concrete deterioration, such as the onset of internal damages and the rate of damage propagation. These results demonstrate the potential of progressive IE data monitoring to enhance the reliability of diagnosing and prognosticating the evolution of concrete damage in marine environment.